The radiation of a rectangular power-bus structure at multiple cavity-mode resonances

The radiation from power-bus structures on high-speed printed circuit boards due to the switching noise current of digital integrated circuits is investigated. The study is based on an analytical cavity-resonator model for a rectangular parallel-plate structure. Based on the application of the field-equivalence principle, the radiated field is calculated from the electric edge-field distribution. For typical board dimensions, several cavity-mode resonances occur within the typical frequency range of interest, leading to relatively high maximum values for radiated emission. The evaluation of the radiation patterns reveals that all (0, nth) resonances have equal maximum amplitudes in the whole mode spectrum. This allows the setting up of an engineering equation for quantifying the noise-current-related maximum radiated field strength, including the dielectric and ohmic loss. Among all geometrical and material parameters, the dielectric thickness is one of the most effective ones to control radiated emission. The theoretical results are well confirmed by accurate measurements carried out in an anechoic room.     

Profiling Voids Embedded in a Slab by a Non-Linear Model

In this paper, by applying a non linear model for the electromagnetic inverse scattering, a technique for the dielectric profiling of a planarly layered medium is investigated and applied to void localization and diagnostics inside a homogeneous lossless slab (one-dimensional geometry). Data are collected under plane wave multifrequency normal incidence. Suitable finite dimensional representations for the unknown functions are introduced and their influence on the model is discussed. The resulting functional equation is solved by the method of weighted residuals and the solution algorithm amounts to minimizing a non quadratic function, where particular attention is devoted to reduce the occurrence of local minima. Finally, the inversion algorithm is validated by applications to both simulated and experimental data.     

Spontaneous erythroid colony formation as the clue to an underlying myeloproliferative disorder in patients with Budd-Chiari syndrome or portal vein thrombosis

Results from this laboratory have shown that bone metabolism is directly related to extracellular pH and that high concentrations of tobramycin released from impregnated polymethylmethacryrate (PMMA) beads has pH-dependent toxic effects on bone. In the present study, beneficial effects of calcium hydroxide-impregnated PMMA were investigated regarding tobramycin toxicity and bone metabolism in chick embryo tibiae in vitro. Also using Ca(OH)2 as a pH regulator, the antibiotic efficacy of tobramycin-impregnated PMMA was evaluated with respect to inhibition of Staphylococcus aureus growth. When Ca(OH)2 was added to PMMA beads containing tobramycin, the beads released hydroxyl and calcium ions into the culture medium and released more antibiotic than beads containing only tobramycin. Bone metabolism (glycolysis, total protein synthesis, and collagen synthesis) was enhanced by Ca(OH)2-impregnated beads with or without tobramycin. Additionally, bacterial growth was inhibited more strongly when S. aureus was incubated with tobramycin- and Ca(OH)2-impregnated PMMA disks than with disks containing only tobramycin. This study demonstrates the feasibility of adding Ca(OH)2 to tobramycin-impregnated PMMA beads as a regulator of local pH and a promoter of bone metabolism for protection of bone when high concentrations of tobramycin are used to treat osteomyelitis. It also suggests that lower concentrations of antibiotic may be effective if Ca(OH)2 and tobramycin are administered simultaneously.     

Association between inflammatory bowel disease and sarcoidosis. Report of two cases and review of the literature

BACKGROUND: Common etiopathogenic factors may explain the association of systemic sarcoidosis with inflammatory bowel disease. METHODS: We report two cases of such an association: one of sarcoidosis that developed 2 years after proctocolectomy for ulcerative colitis and one of sarcoidosis and Crohn's colitis. Factors like increased cellular immunity or circulating immunocomplexes or autoantibodies may have a role. Exogenous agents or familiarity may also be involved. CONCLUSIONS: It is postulated that the association between sarcoidosis and inflammatory bowel disease (both ulcerative colitis and Crohn's disease) does not occur by chance alone and that the two conditions may share some genetic or immunologic alterations. The two diseases, however, follow an independent clinical course.     

A compact model for multiterminal bipolar devices used in smartpower applications

Complex technologies merging low-voltage bipolar devices and vertical current-flow power transistor allow more smart functions at low chip cost but pose problems during the design phase because there is no way to predict the influence of the high-voltage transistor over the control components by using standard bipolar junction transistor (BJT) models. In fact the large inductive load usually present in high-voltage power transistors applications forces both negative substrate voltage and spurious currents that can induce positive feedback among parasitic devices, downgrading the performance of a single device and so of the whole circuit. In this work we introduce a model for the five-terminal bipolar devices used in smart power applications. The model accounts for all main static and dynamic parasitic effects and gives results in very good agreement with experimental data on both simple devices and complex integrated circuits currently implemented in commercial products for microprocessor based engine management systems (EMS's)     

Recommendation of RILEM Technical Committee 250-CSM: Test method for Textile Reinforced Mortar to substrate bond characterization

Textile Reinforced Mortar (TRM), also known as Fabric Reinforced Mortar or Fabric Reinforced Cementitious Matrix, composites are an emerging technology for the external repair and strengthening of existing structures. For most applications, the effectiveness of the TRM reinforcement relies on its bond performance. This recommendation identifies the best practice to characterize the bond behaviour of TRM. A shear bond test method is proposed to determine the peak axial stress (associated with the maximum load that can be transferred from the structural member to the externally bonded TRM reinforcement), the stress–slip relationship and the failure mode that controls the TRM-to-substrate load transfer capacity. Guidelines on specimen manufacturing, experimental setup, test execution, and determination of test results are provided.     

On the relation among answer set solvers

In this paper, we study the relation among Answer Set Programming (ASP) systems from a computational point of view. We consider smodels, dlv, and cmodels ASP systems based on stable model semantics, the first two being native ASP systems and the last being a SAT-based system. We first show that smodels, dlv, and cmodels explore search trees with the same branching nodes (assuming, of course, a same branching heuristic) on the class of tight logic programs. Leveraging on the fact that SAT-based systems rely on the deeply studied Davis–Logemann–Loveland (dll) algorithm, we derive new complexity results for the ASP procedures. We also show that on nontight programs the SAT-based systems are computationally different from native procedures, and the latter have computational advantages. Moreover, we show that native procedures can guarantee the “correctness” of a reported solution when reaching the leaves of the search trees (i.e., no stability check is needed), while this is not the case for SAT-based procedures on nontight programs. A similar advantage holds for dlv in comparison with smodels if the “well-founded” operator is disabled and only Fitting’s operator is used for negative inferences. We finally study the “cost” of achieving such advantages and comment on to what extent the results presented extend to other systems.     

Reconstruction of cellular biological structures from optical microscopy data

Developments in optical microscopy imaging have generated large high-resolution data sets that have spurred medical researchers to conduct investigations into mechanisms of disease, including cancer at cellular and subcellular levels. The work reported here demonstrates that a suitable methodology can be conceived that isolates modality-dependent effects from the larger segmentation task and that 3D reconstructions can be cognizant of shapes as evident in the available 2D planar images. In the current realization, a method based on active geodesic contours is first deployed to counter the ambiguity that exists in separating overlapping cells on the image plane. Later, another segmentation effort based on a variant of Voronoi tessellations improves the delineation of the cell boundaries using a Bayesian formulation. In the next stage, the cells are interpolated across the third dimension thereby mitigating the poor structural correlation that exists in that dimension. We deploy our methods on three separate data sets obtained from light, confocal, and phase-contrast microscopy and validate the results appropriately.