Matrix influence on the piezoelectric properties of piezoelectric ceramic/polymer composite exhibiting particle alignment

This study was addressed to the influence of an electric field strength applied at fabrication process and matrix properties, such as the dielectric constant and the Young's modulus, on “pseudo‐1‐3 piezoelectric ceramic/polymer composite” in order to further enhance the piezoelectricity of that. The pseudo‐1‐3 piezoelectric ceramic/polymer composite consists of linearly ordered piezoelectric ceramic particles in polymer material. Silicone gel, silicone rubber, urethane rubber, and poly‐methyl‐methacrylate, which exhibit different dielectric constants and Young's modulus, were used as matrices to evaluate the matrix influence. The piezoelectricity of the pseudo‐1‐3 piezoelectric ceramic/polymer composite was evaluated using the piezoelectric strain constant d₃₃. The d₃₃ is one of the indices of the piezoelectric properties for piezoelectric materials. As a result, it was confirmed that d₃₃ of the pseudo‐1‐3 piezoelectric ceramic/polymer composite increased with the increase of the electric filed strength applied at fabrication process, though, it reached a constant value at a certain strength value. Further it was confirmed that dielectric constant of the matrix had a small influence on d₃₃ of the pseudo‐1‐3 piezoelectric ceramic/polymer composite, however, in case of matrix of lower Young's modulus, d₃₃ was increase. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41817.     

Unperturbed dimension of poly(4-acetoxystyrene) measured in good and theta solvents

In order to obtain the additional data concerning the unperturbed dimension of poly-4-substituted styrene, light scattering measurements are performed on the twenty-two fractions with molecular weight of (0.91–352)·10⁴ of poly(4-acetoxystyrene) in dioxan at 25°C, from which the molecular weight obtained was found easily to be evaluated with the gel permeation chromatography using THF. Phase separation experiments for this polymer indicate that the theta state is attained in isopropyl acetate at 19.7°C and butyl acetate at 26.8°C. By making viscosity measurements at that state, the value of K_Θ is directly evaluated as 5.4·10^?4 dl g^?1. The limiting viscosity number is also obtained in good solvents, THF and dioxan, at 25°C and constants of the Mark-Houwink-Sakurada equation in each solvent are determined. Further, approximately the same K_Θ as above is obtained from these data with the Stockmayer-Fixman plot. The calculated value of steric factor, 2.37, on this polymer may be plausible, compared with those of polyvinylaromatic derivatives.     

Preparation of Laminin-apatite-polymer Composites Using Metastable Calcium Phosphate Solutions

A synthetic polymer with a laminin-apatite composite layer on its surface would be useful as a percutaneous device. The preparation of such a composite was attempted in the present study using poly（ ethylene terephthalate ） （PET） and polyethylene （PE） as the synthetic polymer. PET and PE plates and those pretreated with an oxygen plasma were alternately dipped in calcium and phosphate ion solutions, and then immersed in a metastable calcium phosphate solution supplemented with laminin （ LCP solution ）. The PET and PE plates pretreated with an oxygen plasma formed a uniform and continuous layer of a laminin-apatite composite on their surfaces. In contrast, the PET and PE plates that had not been pretreated with an oxygen plasma did not form a continuous layer of a laminin-apatite composite on their surfaces. The hydrophilic functional groups on the PET and PE surfaces introduced by the plasma treatment were responsible for the successful laminin-apatite coruposite coating.     

A 0.1-μm delta-doped MOSFET fabricated with post-low-energyimplanting selective epitaxy

A simple fabrication technology for delta-doped MOSFETs, named post-low-energy implanting selective epitaxy (PLISE) is presented. The PLISE technology needs no additional photo-lithography mask, deposition step or etching step even for CMOS devices. The only additional step is growing undoped epitaxial channel layers by UHV-CVD after the channel implantation. With this technology, delta-doped NMOSFETs with 0.1-μm gate length were successfully fabricated. By optimizing the epi-layer thickness and the channel doping level, short-channel effects are suppressed enough to achieve 0.1-μm gate length. Moreover, the junction capacitance at zero bias is reduced by 50%     

The temperature dependence of luminescence from a long-lasting phosphor exposed to ionizing radiation

The temperature dependence of luminescence from a long-lasting phosphor (LLP), SrAl₂O₄ : Eu²⁺,Dy³⁺, exposed to ionizing radiation has been measured to understand the LLP luminescence mechanism. Evaluation of the decay constants of the LLP exposed to -, β- or γ-rays at temperatures from 200 to 390 K showed that the decay constant is divided into four components ranging from 10⁻⁴ to 10⁻¹ s⁻¹ with activation energies of 0.02–0.35 eV.

Total luminous intensity from the LLP with changing irradiation temperature has its maximum value around the room temperature. Irradiation at elevated temperature (390 K) has the total luminescence pattern with monotonous decrease as temperature rises. As a result of evaluating the temperature dependence of luminescence, the luminescence mechanism is considered as follows:

Full-size image

 

Fiber-optic devices for local area network application

Recent developments on fiber-optic devices are reviewed from the local area network (LAN) application viewpoint. Future technical trends are also discussed, along with current research activities. In local area network systems, low device cost and easy maintenance or maintenance-free devices are especially required. Light sources and photodetectors suitable for the systems are described. InGaAsP/InP light emitting diodes can cover a broad application field, up to a gigabits per second super high-speed network region. Optical passive devices, which include branching couplers, switches and connectors, are mentioned as essential components. Compact transmitter/receiver module technology is a key factor in realizing optical-fiber local area network systems. An example of 200-Mbit/s transmitter/receiver module is reported.     

Extensions of polyacrylic acid ammonium salts in the adsorption layer to fluidize alumina slurries

An average shell volume occupied in the adsorption layer on alumina by a polyacrylic acid ammonium salts molecule (PAA) defined as the average area occupied by an adsorbed PAA on alumina multiplied by the average thickness of the water layer at the limit of thickening, has been calculated from the adsorbed amount of PAA and from the flow points of alumina in the presence of PAA of different molecular weights. A steric effect of the PAA dispersant on the dispersion of alumina resulted in a flow with no yield stress. This was due to the change of the extension of PAA in the adsorption shell from a sphere to an ellipsoid with a long axis which exceeded the effective distance that the van der Waals attraction force reaches at a molecular weight for the PAA of between 10 000–20 000.