Liquid Marble Patchwork on Super-Repellent Surface

Liquid marble (LM) is a droplet that is wrapped by hydrophobic solid particles, which behave as a non-wetting soft solid. Based on these properties, LM can be applied in fluidics and soft device applications. A wide variety of functional particles have been synthesized to form functional LMs. However, the formation of multifunctional LMs by integrating several types of functional particles is challenging. Here, a general strategy for the flexible patterning of functional particles on droplet surfaces in a patchwork-like design is reported. It is shown that LMs can switch their macroscopic behavior between a stable and active state on super-repellent surfaces in situ by jamming/unjamming the surface particles. Active LMs hydrostatically coalesce to form a self-sorted particle pattern on the droplet surface. With the support of LM handling robotics, on-demand cyclic activation–manipulation–coalescence–stabilization protocols by LMs with different sizes and particle types result in the reliable design of multi-faced LMs. Based on this concept, a single bi-functional LM is designed from two mono-functional LMs as an advanced droplet carrier.     

Transmittance and cathodoluminescence of AlN ceramics sintered with Ca3Al2O6 as sintering additive

Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca₃Al₂O₆ (C₃A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C₃A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C₃A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density.     

Effects of Seismically Induced Pounding at Expansion Joints of Concrete Bridges

This paper presents the result of a study on the effect of pounding at expansion joints on concrete bridge response to earthquake ground motions. An engineering approach, rather than continuum mechanics approach, is emphasized. First, the dynamic behavior of a damped multidegree-of-freedom bridge system separated by an expansion joint involving an impact is examined by means of the finite element method. Second, the sensitivity analysis of the stiffness in gap elements is performed. Third, usefulness of the analysis method for simulation of pounding phenomena is demonstrated and the effect of pounding on the ductility demands measured in terms of the rotation of column ends is investigated. Two-dimensional finite element analysis using a bilinear hysterestic model for bridge substructure joints and a nonlinear gap element for the expansion joint is performed on a realistic bridge with an expansion joint. The effects of the primary factors on the ductility demand such as gap sizes and characteristics of earthquake ground motion are investigated through a parametric study. The major conclusions are (1) the effect of impact most directly depends on the size of momentum (or pounding magnitude); and (2) the pounding effect is generally found to be negligible on the ductility demand for wide practical ranges of gap size and peak ground acceleration, but is potentially significant at the locations of impact.     

R & D Needs - Drying of Ceramics

New research and development needs for the drying of ceramics are prooosed. The researches on the ceramic drying are briefly reviewed and the role of the drying in the ceramic production process iS summarized. The drying must deal with molded materials and the problem is of significant difference from another drying with particulate materials. It means that the drying must be performed with keeping the molded feature and the insufficient completion of drying and the careless operation influence directly on the product quality The importnance of the R & D on the heat and moisture transfer. shrinking mechanism. the deformation behavior and the strain-stress formation in the molded clay issuggested. The subjects are also pointed out for the further improvement of the ceramic drying process and the precise design of molding with high quality.     

Pulsed KrF excimer laser annealing of silicon solar cell

The pulsed KrF excimer laser annealing of silicon films for solar cell with EBEP-CVD and LP-CVD was studied theoretically and experimentally. Three-dimensional thermal diffusion equation for microcrystalline and amorphous silicon was solved by using the finite difference methods. The results of our heat-flow simulation of laser re-crystallization in a laser irradiation with 50 ns pulse duration almost agree with the experimental results in re-crystallization depth of 0.7 μm for microcrystalline silicon (EBEP-CVD) and 0.4 μm for amorphous silicon (LP-CVD) in a single pulse excimer laser annealing.     

Drying-Induced Strain and Stress: A Review

This paper is to review the works on strains and suesses in materials during drying.The strains and suesses are caused when temperature and moisture gradients are generated in mterials whose volume changes with heating and moisture removal. In such materials. failure and irregular deformion may be generated which affect considerably the qudity of the products after drying. In the first part. modeling procedure is introduced for the analysis of the strain-stress behavior in elaslic. viscous and visccelastic materials combined with heat and moisture transfer. An overview of the works on swains and stresses and drying characteristics are presented for malerials such as porous media. clay. sol-gels. agricultural products and foods in the second part. There are some materials that show both elasticity of the solid phase and viscosity of the fluid phase ( water or solvena∥ or viscoelasticiry. The suesses are often correlated with a suction pressure of fluids in pores and the flow rate is based on Dacy's equation for the elastic and viscous tnedia and a kind of viscoelastic media. The general canstitulive equalions. for suains and svesses are often analyzed with the stain behavior given by a function of moisturr for some media ai well. The emohasis is on the inuoduclion of comprehensive criteria for undersunding the problems of strain and stress development in materials subjected to drying.     

Augmentation by phthalimides of phorbol ester-induced expression of tumor necrosis factor alpha message

N(alpha)-Phthalimidoglutarimide (thalidomide), 2-(2,6-diisopropylphenyl)-1H-isoindole-1,3-dione (PP-33) and its 4,5,6,7-tetrafluoro derivative (FPP-33) augmented 12-O-tetradecanoylphorbol 13-acetate-induced production by human leukemia HL-60 cells of both tumor necrosis factor alpha (TNF-alpha) mRNA and secreted TNF-alpha protein. Intracellular TNF-alpha protein production was increased to a lesser extent.     

Extracellular matrix of opacified anterior capsule after endocapsular cataract surgery

BACKGROUND: We determined the types and distribution of glycosaminoglycans (GAGs) and collagens, in anterior capsular opacification after endocapsular phacoemulsification and aspiration (ECPEA) and intraocular lens implantation. METHODS: Opacified anterior capsules were removed from human eyes after ECPEA. Immunohistochemical staining was performed to determine GAGs with monoclonal antibodies to chondroitin, chondroitin-4-sulfate (C4S), chondroitin-6-sulfate (C6S), dermatan sulfate (DS), and keratan sulfate (KS); collagens with monoclonal antibodies to types I, II, and III collagens; and cellular characteristics with monoclonal antibodies to vimentin, desmin, alpha-smooth muscle actin, and cytokeratin. Decorin mRNA and type I collagen mRNA were detected by in situ hybridization. RESULTS: In the capsules, the C6S, DS, KS, and types I and III collagens were similar to the chemical components found at the adhesion site of the anterior and posterior capsules after extracapsular cataract extraction, and cellular components contained vimentin, desmin, alpha-smooth muscle actin, cytokeratin, decorin mRNA, and type I collagen mRNA. CONCLUSIONS: The GAGs and collagens in opacified anterior capsule after ECPEA were similar to those found during wound healing, although KS is present in normal anterior segment tissue during development and only in the cornea postnatally. These chemical components may be produced by myofibroblast-like cells presumably transformed from lens epithelial cells.     

High performance 35 nm gate length CMOS with NO oxynitride gate dielectric and Ni salicide

The 35 nm gate length CMOS devices with oxynitride gate dielectric and Ni salicide have been fabricated to study the feasibility of higher performance operation. Nitrogen concentration in gate oxynitride was optimized to reduce gate current I/sub g/ and to prevent boron penetration in the pFET. The thermal budget in the middle of the line (MOL) process was reduced enough to realize shallower junction depth in the S/D extension regions and to suppress gate poly-Si depletion. Finally, the current drives of 676 /spl mu/A//spl mu/m in nFET and 272 /spl mu/A//spl mu/m in pFET at V/sub dd/=0.85 V (at I/sub off/=100 nA//spl mu/m) were achieved and they are the best values for 35 nm gate length CMOS reported to date.