Rutile-type TiO2 thin film for high-k gate insulator

We investigated rutile-type titanium dioxide (TiO₂) films for possible use as a high-k gate insulator. The TiO₂ thin films were directly deposited on Si substrates using a RF magnetron sputtering method with a sintered oxide target. A single phase of rutile-type TiO₂ whose dielectric constant of approximately 75 was obtained when the film was deposited in an inert gas atmosphere and annealed at 800 °C in an oxidizing gas atmosphere. The oxygen ions were deficient in the as-deposited film, and consequently, a sufficient oxygen supply was needed to crystallize the film to a single phase of rutile during the post-annealing. However, the interfacial SiO₂ layer between the TiO₂ and the Si substrate simultaneously grew thicker than 2 nm. As the interfacial SiO₂ grew, the leakage current was decreased and the equivalent oxide thickness was increased, in the Au/rutile-type TiO₂/Si capacitor. Therefore, we concluded that the growth of the interfacial SiO₂ layer thicker than 2 nm is inevitable to form the single phase of rutile-type TiO₂ and to decrease the leakage.     

Infrared sensing properties of positive temperature coefficient thermistors with large temperature coefficients of resistivity

Infrared (IR) detecting elements were prepared using positive temperature coefficient (PTC) thermistors with large temperature coefficients of resistivity (α). Their compositions were denoted as Ba_1−x Sr _x Nb_0.003Ti_0.997O₃ + 1 mol % TiO₂ + 0.07 mol %MnO (x=0, 0.2), and their temperature coefficients of resistivity were 78 and 50% K⁻¹, respectively. Their IR sensing properties were measured under the self-regulating heating conditions, and were compared with those of a detector with small α (18 % K⁻¹). It was shown that large α was effective for controlling the element temperature by self-regulating heating and for improving sensitivity. The responsivity,R _v of the element withx=0.2 was 980 VW⁻¹, and was as large as those of pyroelectric detectors. Expressions which normalize the sensitivity and the thermal time constant were derived. From these expressions, criteria for improving some IR sensing properties were obtained.     

Gelation mechanism of agarose and κ-carrageenan solutions estimated in terms of concentration fluctuation

The gelation mechanism of agarose and κ-carrageenan aqueous solutions was investigated by using polarized light scattering and X-ray diffraction techniques in terms of the liquid-liquid phase separation. When an incident beam of He-Ne gas laser was directed to the gel prepared by quenching the agarose solution, the logarithm of scattered intensity increased linearly in the initial stage and tended to deviate from this linear relationship in the latter stage. If the linear increase in the initial stage could be analyzed within the framework of the linear theory of spinodal decomposition proposed by Cahn, the phase diagram indicated that the gelation is attributed to the phase separation due to the concentration fluctuation of solution. Furthermore, in the later stage showing the deviation of the linear relationship, light scattering under Hv polarization condition showed a X-type pattern indicating the existence of optically anisotropic rods, the optical axes being parallel or perpendicular with respect to the rod axis. In spite of the existence of the rods, no crystallites were confirmed by the corresponding X-ray diffraction and DSC measurements. For κ-carrageenan solutions, the logarithm of scattered intensity against time showed a constant value. This indicated that the gelation of κ-carrageenan solutions is independent of liquid-liquid phase separation but is due to the rapid formation of cross-linking points. Accordingly it turns out that the small difference of chemical structure between agarose and κ-carrageenan causes quite different gelation mechanism.     

66/77-kV C-GIS using composite insulation in SF6 gas

A second-generation model of cubicletype gas-insulated switchgear (C-GIS) with composite insulation incorporating SF₆ gas has been developed. The design does not require a gas process in field assembly; it has high reliability and its installation is more rapid; and a further reduction in size is achieved. The design principles are described in detail.     

Wind resistant design of a tall building with an ellipsoidal cross section

This paper summarizes the results of the wind design carried out for the Act Tower building in Japan. Wind tunnel tests were performed in order to estimate the building response for different wind directions. Undesirable building motion perceived by building occupants is also studied and antivibration systems have been installed to solve this problem.     

Mechanical Properties of Alumina/Silicon Carbide Whisker Composites

The improvement of mechanical properties of Al₂O₃/SiC whisker composites has been studied with emphasis on the effects of the whisker content and of the hot-pressing temperature. Mechanical properties such as fracture toughness and fracture strength increased with increasing whisker content up to 40 wt%. In the case of the high SiC whisker content of 40 wt%, fracture toughness of the sample hot-pressed at 1900° decreased significantly, in spite of densification, compared with one hot-pressed at 1850°. Fracture toughness strongly depended on the microstructure, especially the distribution of SiC whiskers rather than the grain size of the Al₂O₃ matrix.     

Delay time compensation based on coefficient of restitution for collision hybrid motion simulator

A hybrid motion simulator embeds a hardware experiment in a numerical simulation loop. However, it is often subjected to the inherent problem of an energy increase in the collision of two pieces of hardware in a loop because of the delay time. This paper proposes a delay time compensation method based on contact dynamics model for a collision hybrid motion simulator under delay time and establishes a compensation method for coupled translational and rotational motion. The model developed in this paper describes linear uniform motion of a floating object during the period of the delay time until the force and torque are observed and non-linear motion according to environmental stiffness after the initial delay time period in contact. By using the above model, compensation parameters are designed based on desired coefficient of restitution with iterative calculation. The proposed method achieves accurate delay time compensation and simultaneously realizes a variable desired coefficient of restitution over a wide range of frequencies. Furthermore, the compensation method for multi-dimensional motion is established under the assumption that the friction effect is very small. The efficiency of the proposed method is verified through collision experiments for the coupled motion in two dimensions.     

Effective Coke Removal in Methane to Benzene (MTB) Reaction on Mo/HZSM-5 Catalyst by H2 and H2O Co-addition to Methane

The catalytic dehydro-aromatization reaction over Mo/HZSM-5 catalyst was drastically stabilized by the co-addition of 5.4% H₂ and 1.8% H₂O to methane feed at 750 °C, 0.3 MPa and methane space velocity of 3000 mL g⁻¹ h⁻¹, suppressing the coke formation effectively, compared with single hydrogen or steam addition.     

Performance of solvothermally prepared Ga2O3-Al2O3 catalysts for SCR of NO with methane

The solvothermal reaction of mixtures of aluminum isopropoxide (AIP) and gallium acetylacetonate (Ga(acac)₃) directly yielded the mixed oxides of γ-Ga₂O₃-Al₂O₃. In the solvothermal synthesis, the crystal structure of mixed oxides was controlled by the initial formation of γ-Ga₂O₃ nuclei. The mixed oxides prepared in diethylenetriamine have extremely high activities for selective catalytic reduction (SCR) of NO with methane as a reducing agent. With increasing crystallite size of the spinel structure, the catalytic activity increased. The ratio of the amount of methane consumed by combustion to total methane conversion was proportional to the density of acid sites on the surface of the mixed oxides. The mixed oxide catalysts prepared in diethylenetriamine had lower densities of acid sites and showed a higher methane-efficiency for CH₄-SCR than those prepared in other solvents. These catalysts maintained their high activity even when the reaction was carried out under the severe conditions (i.e., high space velocity and low NO concentration).