Corner flow in free liquid films

A lubrication-flow model for a free film in a corner is presented. The model, written in the hyperbolic coordinate system ξ = x ² −y ², η = 2xy, applies to films that are thin in the η-direction. The lubrication approximation yields two coupled evolution equations for the film thickness and the velocity field which, to lowest order, describes plug flow in the hyperbolic coordinates. A free film in a corner evolving under surface tension and gravity is investigated. The rate of thinning of a free film is compared to that of a film evolving over a solid substrate. Viscous shear and normal stresses are both captured in the model and are computed for the entire flow domain. It is shown that normal stress dominates over shear stress in the far field, while shear stress dominates close to the corner. This revised version was published online in October 2005 with corrected page numbers.     

Stabilization of bioethanol recovery with silicone rubber‐coated ethanol‐permselective silicalite membranes by controlling the pH of acidic feed solution

In order to produce highly concentrated bioethanol by pervaporation using an ethanol‐permselective silicalite membrane, techniques to suppress adsorption of succinic acid, which is a chief by‐product of ethanol fermentation and causes the deterioration in pervaporation performance, onto the silicalite crystals was investigated. The amount adsorbed increased as the pH of the aqueous succinic acid solution decreased. The pervaporation performance also decreased with decreasing pH when the ternary mixtures of ethanol/water/succinic acid were separated. Using silicalite membranes individually coated with two types of silicone rubber, pervaporation performance was significantly improved in the pH range of 5 to 7, when compared with that of non‐coated silicalite membranes in ternary mixtures of ethanol/water/succinic acid. Moreover, when using a silicalite membrane double‐coated with the two types of silicone rubber, pervaporation performance was stabilized at lower pH values. In the separation of bioethanol by pervaporation using the double‐coated silicalite membrane, removal of accumulated substances having an ultraviolet absorption maximum at approximately 260 nm from the fermentation broth proved to be vital for efficient pervaporation. Copyright © 2005 Society of Chemical Industry     

Carbon nanotubes prepared from three-layered copolymer microspheres of acrylonitrile and methylmethacrylate

Carbon nanotubes (CNTs) were synthesized from fine three-layered copolymer microspheres using the polymer blend technique. Diameter of PMMA core/Poly(AN-co-MMA) shell-1/PMMA shell-2 microspheres, prepared by a radical soap-free emulsion polymerization of methylmethacrylate (MMA) and acrylonitrile (AN), was between 400 nm and 500 nm. Microspheres were subjected to melt-spinning at 305 °C, stabilizing in oxygen at 220 °C for 4 h, and finally carbonizing at 1000 °C for 30 min. FE-SEM study of carbonized sample revealed the presence of CNTs arrays on carbon blocks. Similar arrays were observed in a comparative CNTs sample prepared from three-layered microspheres with the pure PAN shells-1 layers. HRTEM showed that the CNTs derived from copolymer microspheres had different structure when compared to the control sample, i.e. CNTs often adhered to each other and contained the internal compartments. The insufficient PMMA shell-2 coating of copolymer microspheres is believed to be a reason for CNTs adhesion. The possible mechanisms of the carbon block formation and the adhesion of CNTs are introduced.     

Adsorption of trypsin onto poly(2-hydroxyethyl methacrylate)/polystyrene composite microspheres and its enzymatic activity

Poly(2-hydroxyethyl methacrylate)/polystyrene (PHEMA/PS) composite microspheres were produced by emulsifier-free seeded emulsion polymerization for styrene in the presence of PHEMA seed particles. Effects of the surface characteristics of the PHEMA/PS composite microspheres on the adsorption immobilization of trypsin and on its enzymatic activity were discussed. Above 5 mol% of HEMA content, trypsin molecules adsorbed had high activity, 65–100% of the activity of free trypsin. The excellence of the composite microspheres as a carrier for trypsin seems to be closely related with the surface heterogeneity consisting of both hydrophilic and hydrophobic parts.     

采用数值模拟方法研究同时氧化烟气中NO和SO2的可行性添加剂

Mechanism analysis on simultaneous oxidation of NO and SO2 with additives was presented and numerical simulation was developed to investigate the performances of three additives on oxidation of NO and SO2. The simulation result showed that reaction temperature, residence time, additive dose and NO concentration influence the oxidation process significantly. There exists an optimum reaction condition for each additive. n-C4H10 has the strongest ability to oxidize NO and SO2.     

Application of CO2 laser heating zone drawing and zone annealing to nylon 6 fibers

Nlon 6 fibers were zone drawn and zone annealed by using a continuous wave carbon dioxide laser to develop their mechanical properties. A laser‐heating zone drawing was carried out under a applied tension of 35.4 MPa at a power density of 9.65 W · cm^?2, and then the zone‐drawn fiber was annealed. A laser‐heating zone annealing was carried out in two steps at a power density of 9.65 W · cm^?2; the first step was carried out under 423 MPa and the second under 517 MPa. The treating temperature of the fiber heated by the CO₂ laser was measured by using an infrared thermographic camera equipped with a magnifying lens. The treating temperature at the zone drawing is 138°C, and those at the first and the second zone annealing are 121 and 125°C, respectively. The second laser‐heated zone‐annealed fiber has a birefringence of 65.2 × 10^?3, a degree of crystallinity of 54%, and a storage modulus of 21 GPa at 25°C. Wide‐angle X‐ray diffraction patterns for the laser‐heated zone‐drawn and the zone‐annealed fibers show (200) reflection and (002/202) doublet due to only an α form on the equator. The laser‐heated zone‐drawn fiber has a melting endotherm peaking at 216°C and a trace of shoulder on the higher temperature side of its peak, and the laser‐heated zone‐annealed fibers have a single melting endotherm peaking at 216°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1711–1716, 2002     

The role of pressure on thin amorphous carbon films deposited using microwave surface wave plasma CVD

We report the effects of gas composition pressure (GCP) on the optical, structural and electrical properties of thin amorphous carbon (a-C) films grown on p-type silicon and quartz substrates by microwave surface wave plasma chemical vapor deposition (MW SWP CVD). The films, deposited at various GCPs ranging from 50 to 110 Pa, were studied by UV/VIS/NIR spectroscopy, atomic force microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and current–voltage characteristics. The optical band gap of the a-C film was tailored to a relatively high range, 2.3–2.6 eV by manipulating GCPs from 50 to 110 Pa. Also, spin density strongly depended on the band gap of the a-C films. Raman spectra showed qualitative structured changes due to sp³/sp² carbon bonding network. The surfaces of the films are found to be very smooth and uniform (RMS roughness < 0.5 nm). The photovoltaic measurements under light illumination (AM 1.5, 100 mW/cm²) show that short-circuit current density, open-circuit voltage, fill factor and photo-conversion efficiency of the film deposited at 50 Pa were 6.4 μA/cm², 126 mV, 0.164 and 1.4 × 10^− 4% respectively.