Low-loss three-phase frequency conversion using a TDM-PWM technique

A strategy for the realisation of a product-modulation frequency conversion technique is presented. For maximum efficiency and spectral purity, a pulse-width modulation (PWM) circuit is used. The addition of pulse-width-modulated signals from the three input phases to each of the three output phases is accomplished by time-division multiplexing (TDM). The need for the product modulator to accommodate multiplication by negative numbers is eliminated by a modification to the basic equations.     

Solving thermal and phase change problems with the eXtended finite element method

 The application of the eXtended finite element method (X-FEM) to thermal problems with moving heat sources and phase boundaries is presented. Of particular interest is the ability of the method to capture the highly localized, transient solution in the vicinity of a heat source or material interface. This is effected through the use of a time-dependent basis formed from the union of traditional shape functions with a set of evolving enrichment functions. The enrichment is constructed through the partition of unity framework, so that the system of equations remains sparse and the resulting approximation is conforming. In this manner, local solutions and arbitrary discontinuities that cannot be represented by the standard shape functions are captured with the enrichment functions. A standard time-projection algorithm is employed to account for the time-dependence of the enrichment, and an iterative strategy is adopted to satisfy local interface conditions. The separation of the approximation into classical shape functions that remain fixed in time and the evolving enrichment leads to a very efficient solution strategy. The robustness and utility of the method is demonstrated with several benchmark problems involving moving heat sources and phase transformations. Received 20 May 2001 / Accepted 19 December 2001     

The cement mantle in the Exeter impaction allografting technique. A cause for concern

The postoperative radiographs of 35 patients who underwent impaction allografting of the proximal femur were reviewed. Of Gruen zones that could be clearly visualized, 39.9% contained areas where cement was absent. Even when an adequate mantle was present, cement voids were commonly seen. These cement mantle deficiencies were confirmed in a series of cadaveric impaction allografting procedures. They appear to be a consequence, at least in part, of an inadequate differential between trial and actual component sizes. Additionally, 4 patients were identified with significant component migration secondary to radiographically visible cement mantle fractures within the first 6 months of surgery. It is concluded that the surgical technique requires modification to ensure a more consistent cement mantle and clinical result.     

Deep neural network architectures for dysarthric speech analysis and recognition

Neural Computing and Applications - This paper investigates the ability of deep neural networks (DNNs) to improve the automatic recognition of dysarthric speech through the use of convolutional...     

Chemical synthesis and physiological activity of sulfonium analogues of platelet activating factor

Phosphatidylsulfocholine (PSC), the sulfonium analogue of phosphatidylcholine (PC), occurs naturally in some diatoms. The replacement of the −N⁺(CH₃)₃ group by a −S⁺(CH₃)₂ results in an increase in the polar head group size in PSC relative to that of PC, consistent with the observed increase in permeability of PSC bilayers towards urea. It was of interest to see whether replacement of the −N⁺(CH₃)₃ group in platelet activating factor (PAF) by an −S⁺(CH₃)₂ group leads to any change in platelet aggregation or other physiological activity. Synthesis of the sulfonium analogue of PAF was carried out by suitable modifications of known procedures. The PAF-sulfonium analogue was found to have almost the same platelet aggregating activity as PAF itself, in the concentration range 1–20 μM, but a much lower activity in the range 0.01–1 μM. The analogue had little or no effect on the platelet aggregation activity of PAF when added in the concentration range 0.01–1 μM and had about half the hypotensive activity of PAF towards hypertensive CDF male rats. The sulfonium analogue, however, was much more cytotoxic to HL-60 cells than PAF itself, in the concentration range 0–15 μM; replacement of the acetate group by a benzyl group increased the cytotoxicity to the level of that of the methoxy analogue of PAF. Thus, replacement of the −N⁺(CH₃)₃ group by a −S⁺(CH₃)₂ group in the polar head group region of PAF results in a relatively small change in its platelet aggregation activity and a decrease in its hypotensive activity, but greatly increases its antitumor activity. Based on a paper presented at the Third International Conference on Platelet-Activating Factor and Structurally Related Alkyl Ether Lipids, Tokyo, Japan, May 8–12, 1989.     

Durability of sheet molding compounds: Influence of hydrothermal aging on morphology and molecular mobility at microscopic scale

The physicochemical aging for parts of Sheet Molding Compound should be considered for their lifetime management and reusability. This material has a complex morphology and contains porosity due to the process and to shrinkage compensation. This SMC study has two complementary approaches. One describes the morphological consequences of water uptake, showing the decrease in the total amount and the fractal dimension of micro-voids by scanning electron microscopy and image processing. The other shows, by mechanical spectrometry, the effect of water on physical or chemical bonds. In both cases, the “low profile agent” in SMC plays an important role. The molecular mobility was taken as a sensor parameter for the structural changes at the molecular scale, highlighting and quantifying the first steps of the aging. The loss factor level increases, and the activation energies are modified, even for the first aging days. The analysis shows recovery for the material near the relaxation peak of the low profile agent, since the curve recovers its initial shape.     

Fractal characterization of the fissures occuring during polymerization of low-profile unsaturated polyester resins

Blends of unsaturated polyester resin and polyvinylacetate (PVAc) were cured between two glass slides. In this case, the low-profile effect arises by fissuring with a fractal geometry. This paper shows how the fractal dimension of the fissures depends on the PVAc amount and on the cure temperature. These results are discussed with the present knowledge about the polyester network morphology in two phases more or less co-continuous.