Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.     

Experimental investigation of Co and Fe-Doped CuO nanostructured electrode material for remarkable electrochemical performance

The current research work presents a facile and cost–effective co-precipitation method to prepare doped (Co & Fe) CuO and undoped CuO nanostructures without usage of any type of surfactant or capping agents. The structural analysis reveals monoclinic crystal structure of synthesized pure CuO and doped-CuO nanostructures. The effect of different morphologies on the performance of supercapacitors has been found in CV (cyclic voltammetry) and GCD (galvanic charge discharge) investigations. The specific capacitances have been obtained 156 (±5) Fg^?1, 168(±5) Fg^?1 and 186 (±5) Fg^?1 for CuO, Co-doped CuO and Fe-doped CuO electrodes, respectively at scan rate of 5 mVs^?1, while it is found to be 114 (±5) Fg^?1, 136 (±5) Fg^?1 and 170 (±5) Fg^?1 for CuO, Co–CuO and Fe–CuO, respectively at 0.5 Ag^-1 as calculated from the GCD. The super capacitive performance of the Fe–CuO nanorods is mainly attributed to the synergism that evolves between CuO and Fe metal ion. The Fe-doped CuO with its nanorods like morphology provides superior specific capacitance value and excellent cyclic stability among all studied nanostructured electrodes. Consequently, it motivates to the use of Fe-doped CuO nanostructures as electrode material in the next generation energy storage devices.     

Evaluation of microbial toxins,trace elements and sensory properties of a high-theabrownins instant Pu-erh tea produced using Aspergillus tubingensis via submerged fermentation

Theabrownins (TB) are polymeric phenolic compounds associated with the multiple bioactivities of Pu-erh tea, a post-fermented Chinese dark tea. High-TB instant Pu-erh tea was produced via a novel submerged fermentation (SF) using Aspergillus tubingensis and compared with samples produced commercially via the conventional solid-state fermentation (SSF). Viable microorganisms and microbial toxins, especially aflatoxins B₁, G₁, B₂, G₂, cyclopiazonic acid, fumonisins B₁, B₂, B₃ and ochratoxin A, were below the detection limit in all samples. Fewer microbial metabolites were found in SF instant tea compared with the SSF teas. Based on an adult consuming 1 g of instant Pu-erh tea daily, the dietary intake of investigated elements was below the safe limits recommended by various authorities. Tasters viewed the instant tea infusions as very mild, smooth, mellow and full. This suggested that submerged fermentation using A. tubingensis offers a speedy and safe alternative to commercial production of instant Pu-erh tea.     

The effect of copper on the crystallization of hexagonal boron nitride

The crystallization process of hexagonal boron nitride in the presence of copper has been investigated. The positive effect of copper on the crystallinity of boron nitride was observed in the three studied systems of: nitrided boron, nitrided boron–carbon, and previously prepared turbostratic boron nitride. However, the presence of copper hindered the formation of boron carbonitride and produced graphite and boron nitride phases separately. Poor crystallinity was found as a conditio sine qua non for the existence of such a compound. Well-crystallized boron nitride had a very low spacing parameter 0.3328 nm and a regular hexagonal shape.     

Fast internal dynamics in polyelectrolyte gels measured by dynamic light scattering

Summary Dynamic light scattering was used to investigate the dynamics of sodium poly(styrene sulfonate) and fully neutralized poly(acrylic acid) gels as a function of the degree of swelling and weight ratio of cross-linking agent. It was shown that the collective diffusion coefficient increases with increasing degree of swelling and that the diffusion coefficient shows stronger concentration dependence than predicted by scaling arguments. For gel samples measured at the swelling equilibrium, the diffusion coefficient increases with increasing gel concentration for both gel systems.     

NUCLEAR MAGNETIC RESONANCE STUDIES OF ASPHALTENES AND COALS. A NEW APPROACH TO OBTAINING ASPHALTENE STRUCTURAL PARAMETERS WITH DIPOLAR DEPHASING

Apparent carbon aromaticities, fa, of some asphaltenes have been measured by n.m.r. in solution and compared with those obtained by the CP/MAS technique on solid samples. The aromaticities were also measured for several Alberta plains coals. From the 1H solution spectra and 13C solid nmr spectra of asphaltenes, some of their skeletal features, not obtainable from solution spectra only, have been suggested.     

Kinetic Monte-Carlo simulation of network formation

Summary the simulation described in Part I was applied to random step polyaddition of a trifunctional monomer and the results were compared with exact solution for an infinite system. The gel point conversions, the weight-average degree of polymerization before (P _w) and beyond (P _w,sol) the gel point, the sol fraction and the cycle rank were used for comparison. The best way for detection of the gel point conversion is the extrapolation of the gel fraction, w _g, to w _g=0. The largest fluctuations are exhibited by P _w and P _w,sol. To get results closer to the exact ones, one can repeat several experiments with smaller number of units or increase the number of units, the former way being somewhat more economical. Typical orders of magnitude used were 10⁷ monomeric units.     

Correction to: “SPOCU”: scaled polynomial constant unit activation function

Neural Computing and Applications - Addendum on SPOCU fitting and Erratum.     

A case of using the Semantic Interoperability Framework for custom orthopedic implants manufacturing

The efficiency and effectiveness of the daily practice in orthopedic surgery depend on the availability, interoperability and unique access to a wide set of information, related to the patient’s medical record and diagnosis, domain knowledge and available resources and staff. The most important of the tangible resources, needed for the therapeutic or preventive actions are orthopedic implants. In some cases, the implants may be highly complex and customized products, which need to be manufactured (assembled) on basis of the above information in a shortest possible timeframe. In this paper, the case of the custom orthopedic implants manufacturing is described from the perspective of the collaborative enterprising, with special consideration of the interoperability issues of the involved enterprise collaboration. It is shown how the previously developed Semantic Interoperability Framework can be used to improve the efficiency of the manufacturing and other relevant processes.