Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.     

Linear correlation between pH value of stimulated beef and electrical current intensity

The aim of the present study was to determine mathematical relationships between pH changes in beef 24 h post-slaughter and changes in the intensity of electrical current flowing through bull and heifer carcasses during high-voltage electrical stimulation. The electrical stimulation was applied 40 min postmortem for 120 s. The pH values of m. longissimus thoracis et lumborum were analyzed in the function of electrical current intensity changes and its change during electrical stimulation. Mathematical linear correlations of the y = ax ± b type were demonstrated between pH values at 2, 6, and 24 h postmortem and the initial (I_i) and ultimate (I_u) electrical current intensity values, the difference between them and the initial pH values determined before electrical stimulation. High multiple correlation coefficients (R² = 0.416, α ≤ 0.001) between I_u and pH values 24 h post-slaughter enabled concluding that there is a possibility to predict a pH value of stimulated carcass with high accuracy, and thus also beef quality, based merely on the ultimate electrical current intensity values.     

The influence of volume fraction of amorphous phase on corrosion resistance of Mg67Zn 29Ca 4 alloy

The aim of this study was to investigate the structure and corrosion resistance of amorphous, amorphous‐crystalline, and crystalline Mg₆₇Zn₂₉Ca₄ alloy for biodegradable applications. This paper presents a preparation method and results of the structural characterization and corrosion resistance analysis of the material. Samples were prepared in the form of 3 mm diameter rods. The structure of the alloy was examined with the use of X‐ray diffractometry and scanning electron microscopy. The thermal properties of the samples were examined with differential scanning calorimetry (DSC). Results of DSC analysis were used to determine heat treatment temperatures, allowing to obtain different fractures of crystalline phase in the material. Corrosion resistance of heat‐treated samples was investigated by immersion tests and electrochemical measurements performed in the simulated body fluid. The X‐ray diffraction results confirmed that the prepared Mg₆₇Zn₂₉Ca₄ alloy's structure is fully amorphous. After heat treatment, samples with different fractions of amorphous phase in the structure were obtained. Immersion tests of the samples showed that the structure significantly influenced corrosion resistance in examined materials. It should be pointed out, that certain amounts of crystalline phase in amorphous matrix can greatly improve the corrosion resistance of Mg₆₇Zn₂₉Ca₄ alloy.     

Strength of pure alumina ceramics above 1 GPa

Up to now, commercially available alumina ceramics were claimed to have strength between 400 and 550 MPa. However, our study shows strength ~ 2 times higher for commercially available alumina than commonly believed. The average and characteristic strength, measured on 31 pure alumina ceramic discs by ball on three balls (B3B) test, were 1205 ± 93 MPa and 1257 MPa, respectively, with a Weibull modulus of m = 11.8. Tested specimens were in form of discs with a diameter of 5 mm and thickness 0.5 mm. The grain size distribution of the alumina is bimodal with an average grain size of ~ 850 nm measured at the surface. The fracture reveals a mixed transgranular / intergranular failure mode. To avoid incorporation of additional flaws, the discs were tested as sintered. The characteristic flexural strength measured in B3B was recalculated according to Weibull theory for standard 4-point bending bars of size 3 × 4 × 45 mm as bend 856 MPa. The measured strength of nearly 900 MPa shows the potential of strength for high purity alumina ceramics.     

Low concentration short time ozonation of rapeseed seeds reduces the stability of the oil and content of some antioxidant components

Ozonation is an innovative way to preserve high quality of seed during storage and it is an alternative to harmful organophosphorus agents. Disclosure of changes in the rapeseed oil under the influence of oxidative action of ozone on the seeds was the aim of the work and is presented for the first time. Two ozone concentrations and different length of ozonation were applied. The changes in tocopherols, phenolics, flavonoids contents, antiradical activity and oxidative stability were examined. The average vitamin E concentration was 33 mg per 100 g of oil before and 31.7 after ozonation of seeds. The average content of phenolic compounds was 14.3 mg of sinapic acid g⁻¹ and 16.9 after the ozone treatment. Changes in the flavonoids content and antioxidant activity were observed too. Ozonation caused a decrease in the vitamin E concentration which resulted also in reducing the quenching of free radicals and reduction of oil induction time.     

Nonuniformity of phase structure in immiscible polymer blends

This article is focused on the phase structure development in immiscible polymer blends during melt mixing. Nonuniformity of the phase structure, i.e., the coexistence of areas containing particles with markedly different size distribution, was detected in quenched and compression molded samples of a number of various blends prepared by long and intensive mixing in the chamber of a Plasticorder. The same effect was found also for polystyrene/polyamide blends prepared in a twin‐screw extruder. It was shown that neglecting nonuniformity of the phase structure can lead to considerable error in evaluation of the effect of system parameters on the blend morphology. The reasons for the effect were discussed and it was found that inhomogeneous flow field in mixers is a plausible explanation of the nonuniform phase structure. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Efficient computer implementation of the renormalized coupled-cluster methods: The R-CCSD[T], R-CCSD(T), CR-CCSD[T], and CR-CCSD(T) approaches

The recently proposed renormalized (R) and completely renormalized (CR) coupled-cluster (CC) methods of the CCSD[T] and CCSD(T) types have been implemented using recursively generated intermediates and fast matrix multiplication routines. The details of this implementation, including the complete set of equations that have been used in writing efficient computer codes, memory requirements, and typical CPU timings, are discussed. The R-CCSD[T], R-CCSD(T), CR-CCSD[T], and CR-CCSD(T) computer codes and similar codes for the standard CC methods, including the LCCD, CCD, CCSD, CCSD[T], and CCSD(T) approaches, have been incorporated into the gamess package. Information about the main features of this new set of CC programs is provided.