Shear mode coupling and tilted grain growth of A1N thin films in BAW resonators.

Polycrystalline A1N thin films were deposited by RF reactive magnetron sputtering on Pt(111)/Ti electrode films. The substrates were tilted by an angle ranging from 40 degrees to 70 degrees with respect to the target normal. A low deposition temperature and a high sputter gas pressure were found ideal for tilted growth. The resulting grain tilt angle amounts to about half the substrate tilt angle. For coupling evaluation, 5 GHz solidly mounted resonator structures have been realized. The tilted grain A1N films exhibited a permittivity in the 9.5-10.5 range and loss tangent of 0.3%. Two shear modes as well as the longitudinal mode could be clearly identified. The coupling coefficient k2(eff) of the fundamental thickness shear mode (TS0) was found to be about 0.5%, which is compatible with a c-axis tilt of about 6 degrees.     

Rheological behaviour of polysaccharide aqueous solutions

Several data relative to the viscosity of water-soluble polysaccharide solutions were collected from the literature and processed by different rheological models. Some relationships between the viscosity of these polymer solutions, their molecular weight and their solution concentrations, were established and their validity checked. Thus, an accurate equation correlating the viscosity and both the shear rate and the solution concentration of different water soluble polysaccharides (xanthan, hyaluronan, carboxymethylcellulose) was deduced on the basis of Cross' model which suggests two domains in which the viscosity is constant, i.e. very low and very high shear rate ranges. Then, an expression relating the zero-shear viscosity (A) and the concentration of their solutions was proposed. Finally, an alternative equation to that of Mark–Houwink correlating the molecular weight and the intrinsic viscosity of the water-soluble polysaccharides studied in this paper was found.     

Local Convergence of the Lavrentiev Method for the Cauchy Problem via a Carleman Inequality

The purpose is to perform a sharp analysis of the Lavrentiev method applied to the regularization of the ill-posed Cauchy problem, set in the Steklov-Poincaré variational framework. Global approximation results have been stated earlier that demonstrate that the Lavrentiev procedure yields a convergent strategy. However, no convergence rates are available unless a source condition is assumed on the exact Cauchy solution. We pursue here bounds on the approximation (bias) and the noise propagation (variance) errors away from the incomplete boundary where instabilities are located. The investigation relies on a Carleman inequality that enables enhanced local convergence rates for both bias and variance errors without any particular smoothness assumption on the exact solution. These improved results allows a new insight on the behavior of the Lavrentiev solution, look similar to those established for the Quasi-Reversibility method in [Inverse Problems 25, 035005, 2009]. There is a case for saying that this sort of ??super-convergence?? is rather inherent to the nature of the Cauchy problem and any reasonable regularization procedure would enjoy the same locally super-convergent behavior.     

Structured estimation of tire forces and the ground slope using SM observers

In agricultural context, the principal cause of serious accidents for all-terrain vehicles(ATVs) is rollover. The most important parameters related to this risk is the ground slope. In this paper, we propose a structured observer to estimate the system states and the longitudinal tire forces using only wheel angular velocities measurement. The robust estimation is based on a second order sliding mode observer. This estimation is then used to build up a ground slope estimation. The algorithm is composed by two cascaded estimators. This structured estimation is then applied to the model of an agricultural vehicle G7(GregoireTM) integrated in the driving simulation environment SCANeRTM-Studio.     

Nanocomposites of PBAT and cellulose nanocrystals modified by in situ polymerization and melt extrusion

Cellulose nanocrystals (CNC) were successfully grafted with a low molecular weight poly(butylene glutarate) through an in situ polymerization procedure. The grafting treatment decreased the CNC hydrophilic character and increased the onset of their thermal degradation by approximately 20°C, thus increasing the possibilities of CNC application. Composites of grafted and nongrafted CNC with a poly(butylene‐adipate‐co‐terephthalate) (PBAT) matrix were prepared by melt extrusion. The CNC addition led to an increase of 50% of the tensile elastic modulus of the PBAT. In addition, dynamic mechanical thermal analysis showed that the composite with CNC retained its high modulus even at temperatures far above the glass transition temperature of PBAT. At 60°C the storage modulus of the composite with CNC was approximately 200% higher than that of the pure PBAT. Thus, in this work, nanocomposites of improved properties were obtained through a combination of in situ polymerization and melt extrusion. POLYM. ENG. SCI., 56:1339–1348, 2016. © 2016 Society of Plastics Engineers     

A discounted integrated inspection-maintenance model for a single deteriorating production facility

In this paper, we address the problem of determining optimum inspection schedules for a single deteriorating production system with a predetermined replacement cycle. It is assumed that, at different discrete points in time over the fixed planning horizon, the facility is inspected to detect its operating state and then it goes over an imperfect preventive maintenance routine to enhance its operating performance. Moreover, the facility undergoes minimal repair once detected in an “out‐of‐control” state. We also adopt the concept of discounted cash flow analysis to account properly for the effect of time value of money on the inspection policies. Under these settings, we formulate the discounted integrated inspection‐maintenance problem as a dynamic programming model with general time to failure distribution. After illustrating the model with a numerical example, we perform sensitivity analysis to investigate the effects of some input parameters on the expected present worth and the number of inspections.     

New separation method of metal/plastic micronized particles using travelling wave conveyors

The paper reports an experimental investigation for studying the movement dynamics and the separation of micronized particles on a poly-phase travelling wave conveyor (TWC). A digital balance and a sensitive electrometer controlled by Labview software were used to analyse the velocity and the material flow rate on a three-phase conveyor with respect to the variation of both the amplitude and the frequency of the applied voltage. It was found that about 80% of the particles mass move together in one single wave and that the electric charge gained by the particles increases with the intensity of the electric field. Moreover, preliminary experiments showed that it is possible to separate a granular mixture of plastic and copper micronized particles using a TWC. Successful experiments were carried out on micronized samples of both electric cable and electronic card wastes. High purity metal was recovered.