High-efficiency Silicon Solar Cells: A Review

Over the past few decades, crystalline silicon solar cells have been extensively studied due to their high efficiency, high reliability, and low cost. In addition, these types of cells lead the industry and account for more than half of the market. For the foreseeable future, Si will still be a critical material for photovoltaic devices in the solar cell industry. In this paper, we discuss key issues, cell concepts, and the status of recent high-efficiency crystalline silicon solar cells.     

Exploiting ILP, TLP, and DLP with the polymorphous trips architecture

The Tera-op reliable intelligently adaptive processing system (TRIPS) architecture seeks to deliver system-level configurability to applications and runtime systems. It does so by employing the concept of polymorphism, which permits the runtime system to configure the hardware execution resources to match the mode of execution and demands of the compiler and application.     

The process window for diamond deposition from the vapor phase with sulfur in the C–H–O feed gas mixtures

Theoretical predictions using a modified radical species ternary diagram for C–H–O system indicate that addition of sulfur expands the C–H–O gas phase compositional window for diamond deposition. Sulfur addition to no-growth domain increases the carbon super-saturation by binding the oxygen and the addition of sulfur to the non-diamond domain reduces the heavy carbon super-saturation by decreasing C_nH_m species concentration in the gas phase. The overall effect of sulfur addition to gas phase mixtures is characterized as that of oxygen addition to the C–H system, i.e. expansion of the compositional window over which diamond can be deposited from the gas phase. In addition, the increasing sulfur concentration to diamond domain feed gases beyond 2000 ppm did not affect the steady state gas phase composition but the quality of diamond was reduced.     

Biparietal diameter: a useful measure for determining gestational age of human abortuses

BACKGROUND: The crown-rump length is conventionally used to determine the age of human abortuses. However, it is not reliable as it is dependent on the positioning of the conceptus. We compared this with the biparietal diameter and foot length for determining the gestational age. METHODS: Different measurements, commonly used to assess gestational age, were measured in 146 human abortuses for which an accurate obstetric history could not be elicited. Measurements taken were crown-rump length, biparietal diameter and foot length. These were correlated with the observations at antenatal examinations before finalizing the approximate age. RESULTS: Multiple regression analysis of the data indicated that of the three measurements, the biparietal diameter was the most reliable for determining foetal gestational age between 8 and 26 weeks. The age determined with the biparietal diameter correlated well with that of abortuses with an accurate obstetric history. CONCLUSION: The biparietal diameter of a human foetus may be used to determine its age if the obstetric history regarding the period of gestation is vague or not available.     

Travelling-wave photodetectors with 172-GHz bandwidth and 76-GHzbandwidth-efficiency product

Results of the first fabrication and measurement of travelling-wave photodetectors are reported. The devices have bandwidths as high as 172 GHz, the highest reported for a p-i-n photodetector, and bandwidth-efficiency products as large as 76 GHz, the largest reported for any photodetector without gain. Comparisons with vertically illuminated and waveguide photodetectors fabricated on the same wafer establish the superior performance of travelling-wave photodetectors. Microwave loss on the travelling-wave photodetector structure is identified as a bandwidth limitation     

Rolling contact fatigue behavior of sintered and hardened steels

Powder-metal-processed bearings and gears are finding increasing application because of their economical and technical advantages. The residual pores from the sintering operatives act as lubricant pockets and dampen sound and vibration. However, porosity also decreases the mechanical strength and reduces the life of components fabricated by powder processing relative to similar wrought components. The rolling contact fatigue behavior of sintered and heat treated steel rollers was investigated using a fatigue test machine designed and fabricated for that purpose. The powder-metal-processed and the wrought steel rollers that were tested had similar composition and hardness and were mated against wrought steel rollers of high hardness. The contact stress versus number of cycles to failure data showed that the wrought steel had a very high endurance limit under rolling contact fatigue compared to the sintered steels investigated. Rolling contact fatigue behavior was found to depend on the porosity present in the material. Large surface peeling failures and pitting type fatigue failures were observed in the sintered and hardened steels, while only pitting type failures were observed in the wrought steels     

Realization of a temperature sensor using both two- and three-dimensional photonic structures through a machine learning technique

A temperature sensor based on photonic crystal structures with two- and three-dimensional geometries is proposed, and its measurement performance is estimated using a machine learning technique. The temperature characteristics of the photonic crystal structures are studied by mathematical modeling. The physics of the structure is investigated based on the effective electrical permittivity of the substrate (silicon) and column (air) materials for a signal at 1200 nm, whereas the mathematical principle of its operation is studied using the plane-wave expansion method. Moreover, the intrinsic characteristics are investigated based on the absorption and reflection losses as frequently considered for such photonic structures. The output signal (transmitted energy) passing through the structures determines the magnitude of the corresponding temperature variation. Furthermore, the numerical interpretation indicates that the output signal varies nonlinearly with temperature for both the two- and three-dimensional photonic structures. The relation between the transmitted energy and the temperature is found through polynomial-regression-based machine learning techniques. Moreover, rigorous mathematical computations indicate that a second-order polynomial regression could be an appropriate candidate to establish this relation. Polynomial regression is implemented using the Numpy and Scikit-learn library on the Google Colab platform.

     

Study of Magnetic and Electrical Properties of Poly(o-phenylenediamine)/Manganese Substituted ZnFe2O4 Nanocomposites

Journal of Inorganic and Organometallic Polymers and Materials - Different concentrations of ZnFe2O4 and manganese substituted ZnFe2O4 nanoparticles (10%, 20% and 30%) dispersed...     

Observations on the role of oxide scales in high-temperature erosion-corrosion of alloys

The results are presented of exposure to a controlled high-temperature erosive gas stream of a series of alloys, which were selected to represent the range of microstructures and mechanical properties available in commercial high-temperature alloys. Analysis of the kinetic and morphological data suggested that the high-temperature oxidation behavior of a given alloy plays a very important role in determining its erosion-corrosion behavior under the conditions studied. In terms of relative behavior, alloys which are weak but ductile at temperature, and which form tenacious oxide scales, exhibited the highest resistance to high-temperature erosion-corrosion. Simple models were developed to describe the expected interaction between high-temperature oxidation and erosion.