Determination of horseradish peroxidase concentration using the chemiluminescence of Cypridina luciferin analogue, 2-methyl-6-(p-methoxyphenyl)-3,7-dihydroimidazo[1,2-a]pyrazin-3-one

The chemiluminescence of the Cypridina luciferin analogue, 2-methyl-6-(p-methoxyphenyl)-3,7-dihydroimidazo[1,2-a]pyrazin++ +-3-one (MCLA) was observed at 462 nm in the presence of horseradish peroxidase (HRP) and the total spectrum of light emitted was found to depend linearly on HRP concentration. Methods for the determination of HRP concentration using the chemiluminescence was investigated. HRP could be detected in the range from 100 pmol/L to 100 nmol/L under the optimum condition, H2O2 (10 mmol/L) and MCLA (10 mumol/L) at pH 5.8.     

Carbon fiber from natural biopolymer Bombyx mori silk fibroin with iodine treatment

Carbon fibers were prepared from silk fibers after an iodine treatment and the carbon yield, fiber morphology, structure and mechanical properties were investigated. A single or multi-step carbonization process was used for the preparation. In the single step process, silk fibroin (SF) fibers were heated from 25 to 800 °C with a heating rate of 5 °C min⁻¹ under Ar atmosphere. However, the carbon fiber obtained was partially melted and was too fragile to handle. For better performance, SF fibers were treated with iodine vapor at 100 °C for 12 h and untreated and iodinated SF fibers were heated from 25 to 800 °C by a multi-step carbonization process, which was defined based on the optimum thermal degradation rate of silk. In this multi-step process, the carbon fibers obtained from iodinated SF were structurally intact and stable in appearance, and the carbon yield achieved was ca. 36 wt.%, much higher than the value for untreated SF. X-ray diffraction, Raman spectroscopy and transmission electron microscopic observation revealed that the obtained carbon fibers from both untreated and iodinated SFs had a basically amorphous structure. The strength of carbon fibers prepared from iodinated SF using the multi-step carbonization was considerably increased compared to that of untreated SF. According to viscoelastic measurement, by heating above 280 °C the iodine introduced intermolecular cross-linking of the SF, and its melt flow was inhibited which produced a higher yield and better performance of the carbon fiber.     

Self-aligned fabrication of single crystal diamond gated field emitter array

This paper describes a self-aligned fabrication process for diamond gated field emitter array (FEA). Utilizing the non-conformal coverage sputtering conditions of silicon oxide, an interesting “sphere on cone” structure is formed on diamond nano tip array, which is the key point of gate hole opening process. This structure causes shadowing at certain regions of side-wall during Ti / Au gate metal deposition. Removal of “sphere” by wet etching leads to the successful fabrication of a single crystalline diamond gated FEA. Scanning electron microscope observations reveal the fabrication of a uniform emitter array with tip radius of curvature (20 nm) and gate hole (1.4 μm). We also confirmed that no noticeable physical damage exists on tip. In field emission characteristics of the fabricated single crystal diamond gated FEA, gate voltage control of field emission current is realized.     

Gaze direction based vehicle teleoperation method with omnidirectional image stabilization and automatic body rotation control

In robot teleoperation, a robot works as a physical agent at a remote site for a robot operator. There are mainly two tasks in robot teleoperation using camera images: environment recognition using visual information and robot control according to the recognition. In this paper, we propose a gaze direction based vehicle teleoperation method with an omnidirectional image stabilization and an automatic body rotation control. In the proposed method, we manage above two tasks in the same manner that are usually treated separately. This method is an intuitive vehicle teleoperation method where an operator do not need to have concern about vehicle body orientations and can absorb differences of vehicle driving mechanisms. That is, this method frees an operator from being bothered from controlling a vehicle and the operator can concentrate on where he/she intends to go. This method mainly consists of two technologies: an omnidirectional image stabilization technology and automatic body rotation control. The conducted experiments show effectiveness of the proposed method.     

A Hemispherical Image Sensor Array Fabricated with Organic Photomemory Transistors

Hemispherical image sensors simplify lens designs, reduce optical aberrations, and improve image resolution for compact wide-field-of-view cameras. To achieve hemispherical image sensors, organic materials are promising candidates due to the following advantages: tunability of optoelectronic/spectral response and low-temperature low-cost processes. Here, a photolithographic process is developed to prepare a hemispherical image sensor array using organic thin film photomemory transistors with a density of 308 pixels per square centimeter. This design includes only one photomemory transistor as a single active pixel, in contrast to the conventional pixel architecture, consisting of select/readout/reset transistors and a photodiode. The organic photomemory transistor, comprising light-sensitive organic semiconductor and charge-trapping dielectric, is able to achieve a linear photoresponse (light intensity range, from 1 to 50 W m⁻²), along with a responsivity as high as 1.6 A W⁻¹ (wavelength = 465 nm) for a dark current of 0.24 A m⁻² (drain voltage = −1.5 V). These observed values represent the best responsivity for similar dark currents among all the reported hemispherical image sensor arrays to date. A transfer method was further developed that does not damage organic materials for hemispherical organic photomemory transistor arrays. These developed techniques are scalable and are amenable for other high-resolution 3D organic semiconductor devices.     

Hydrothermal preparation of tailored hydroxyapatite

Hydrothermal vapor treatment method was applied for preparation of ceramic biomaterials. Hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂; HA) ceramics prepared by sintering with random crystal surface have already been used as bone-repairing materials which can directly bond to natural bones. If materials of HA could have the tailored specific crystal surface, they should have the advantage of adsorptive activity and osteoconductivity in comparison with the sintered HA. In the present study, porous HA sheets of about 50 μm to 1 mm in thickness and porous HA granules of about 50 μm to 1 mm in size with tailored crystal surface were prepared by the hydrothermal vapor exposure method at temperatures below 200°C. Porous sheets and porous granules of HA with controlled crystal surface should be suitable for scaffold of cultured bone, for bone graft material and for drug delivery system (DDS).     

Recovery of serum proteins using cellulosic affinity membrane modified by immobilization of CU2+ ion

An affinity membrane was prepared from a porous cellulose membrane, and adsorption and recovery of serum proteins were investigated from the viewpoint that affinity membranes are efficacious against separation and purification of biomaterials. Into the cellulose membrane, iminodiacetate (IDA) group that acts as a ligand to metal ions was introduced (Cell–IDA membrane), and then Cu²⁺ ion was immobilized (Cell–IDA–Cu membrane). Bovine serum albumin (BSA) and γ-globulin (BγG), which are the major proteins in blood, were adopted as model proteins to be separated. The Cell–IDA–Cu membrane had large adsorption capacity for these proteins despite the low degree of modification. The amounts of proteins adsorbed on the Cell–IDA–Cu membrane increased with increasing pH, and BγG was adsorbed more than BSA. High protein recoveries from the Cell–IDA–Cu membrane were obtained. The separation of these proteins was also conducted under the optimum conditions of adsorption and recovery, and BγG was concentrated more than BSA although the initial concentration of BγG was lower than that of BSA. © 1996 John Wiley & Sons, Inc.     

Preparation of Polymer-Based Nanocomposites Composed of Sustainable Organo-Modified Needlelike Nanoparticles and Their Particle Dispersion States in the Matrix

Polymer-based nanohybrid materials were created using sustainable sepiolite clay composed from ubiquitous elements. Although sepiolite is generally recognized as a fibrous natural clay mineral, it turned out to be an acicular microcrystal because of the organo-modification of the outermost surface. Surface modification was performed using phosphonic acid derivatives containing hydrocarbon chains or fluorocarbon chains. Formation of a bidentate bond enhanced the desorption temperature and made nanocomposite preparation possible by melt compounding with polymers having a high melting point. As a result of organo-modification, amphiphilic sepiolite was obtained, and nanodispersion in an organic solvent was achieved. This technology was useful for detailed evaluation of sepiolite morphology. The nanocomposite of crystalline polymers/organo-modified sepiolites achieved uniform dispersion of these nanofillers in the matrix polymer. The introduction of 1 wt% nanofillers did not impair the transparency of the matrix polymer. As a result, a lamellae structure of the polymer developed, the crystallinity increased, and the mechanical properties improved. In addition, the crystallization temperature was improved, indicating that organo-modified sepiolites may act as a nucleating agent. It was found that sepiolite nanofiller with a highly aggregated tendency can achieve a well-nanodispersed state, even in phase-separable fluoropolymers, by applying fluorocarbon modification. POLYM. ENG. SCI., 60:541–552, 2020. © 2019 Society of Plastics Engineers