Ferroelastic domain structure and phase transition in single-crystalline [PbZn1/3Nb2/3O3]1-x[PbTiO3]x observed via in situ x-ray microbeam

(1-x)Pb(Zn_1/3Nb_2/3)O₃-xPbTiO₃ ((1-x)PZN-xPT in short) is one of the most important piezoelectric materials. In this work, we extensively investigated (1-x)PZN-xPT (x = 0.07–0.11) ferroelectric single crystals using in-situ synchrotron μXRD, complemented by TEM and PFM, to correlate microstructures with phase transitions. The results reveal that (i) at 25 °C, the equilibrium state of (1-x)PZN-xPT is a metastable orthorhombic phase for x = 0.07 and 0.08, while it shows coexistence of orthorhombic and tetragonal phases for x = 0.09 and x = 0.11, with all ferroelectric phases accompanied by ferroelastic domains; (ii) upon heating, the phase transformation in x = 0.07 is Orthorhombic → Monoclinic → Tetragonal → Cubic. The coexistence of ferroelectric tetragonal and paraelectric cubic phases was in-situ observed in x = 0.08 above Curie temperature (T_C), and (iii) phase transition can be explained by the evolution of the ferroelectric and ferroelastic domains. These results disclose that (1-x)PZN-xPT are in an unstable regime, which is possible factor for its anomalous dielectric response and high piezoelectric coefficient.     

Unsteady behavior of leading-edge vortex and diffuser stall in a centrifugal compressor with vaned diffuser

The characteristics of a rotating stall of an impeller and diffuser and the evolution of a vortex generated at the diffuser leading-edge (i.e., the leading-edge vortex (LEV)) in a centrifugal compressor were investigated by experiments and numerical analysis. The results of the experiments revealed that both the impeller and diffuser rotating stalls occurred at 55 and 25 Hz during off-design flow operation. For both, stall cells existed only on the shroud side of the flow passages, which is very close to the source location of the LEV. According to the CFD results, the LEV is made up of multiple vortices. The LEV is a combination of a separated vortex near the leading- edge and a longitudinal vortex generated by the extended tip-leakage flow from the impeller. Therefore, the LEV is generated by the accumulation of vorticity caused by the velocity gradient of the impeller discharge flow. In partial-flow operation, the spanwise extent and the position of the LEV origin are temporarily transmuted. The LEV develops with a drop in the velocity in the diffuser passage and forms a significant blockage within the diffuser passage. Therefore, the LEV may be regarded as being one of the causes of a diffuser stall in a centrifugal compressor.     

Application of CANDLE burnup to block-type high temperature gas cooled reactor

The CANDLE burnup strategy, where the distributions of fuel nuclide densities, neutron flux, and power density move with the same constant speed and without any change in their shapes, is applied to the block-type high temperature gas cooled reactor. If it is successful, a burnup control rod can be eliminated, and several merits are expected. This burnup may be realized by enriched uranium and burnable poison with large neutron absorption cross-section. With the fuel enrichment of 15%, gadolinium concentration of 3.0%, and fuel cell pitch of 6.6 cm, the CANDLE burnup is realized with the burning region moving speed of 29 cm/year and the axial half-width of power density distribution of 1.5 m. When the concentration of natural gadolinium is higher, the burning region moving speed becomes slower and the burnup becomes higher, though the effective neutron multiplication factor becomes smaller. When U-235 enrichment is higher, the effective neutron multiplication factor becomes larger, the speed becomes slower, and the burnup becomes higher. When the pitch is wider, the effective neutron multiplication factor becomes larger, the speed becomes faster, and the burnup becomes higher.     

Effect of nitrate on corrosion of austenitic stainless steel in boiling nitric acid solution containing chromium ions

The oxidation behavior of chromium and the corrosion behavior of austenitic stainless steel in boiling nitric acid solution containing highly concentrated nitrates were investigated using UV-visible spectroscopic measurements, Raman spectral measurements, immersion tests, and potentiodynamic polarization measurements. The oxidation rate measurement of chromium from Cr(III) to Cr(VI) was performed by 1 M boiling nitric acid solution containing each highly concentrated nitrates: Al(NO₃)₃, Nd(NO₃)₃, Ca(NO₃)₂, Mg(NO₃)₂, and NaNO₃ as a simulant of uranium nitrate in uranium concentrator in reprocessing plants. As a result, the rate of chromium oxidation was different depending on the added nitrates even at the same nitric acid concentration. In addition, the oxidation rate of chromium was increased with increasing the calculated partial pressure of nitric acid in consideration of the hydration of cation of nitrates. Furthermore, the corrosion rate of type 310 stainless steel was accelerated by the solution having a high chromium oxidation rate containing nitrates. These results indicated that the acceleration of the corrosion rate in the solutions depending on the oxidation rate of chromium, and the rate is affected by the salt-effect of nitrates.     

A simple treatment of increased gap due to fuel assembly bowing through correction of cross sections

Increased fuel assembly gap due to bowing in commercial light-water reactors (LWRs) has an impact on local pin-power distribution due to increased local moderation. In order to consider the effect of increased assembly gap without explicit consideration of increased gap width, a correction method of cross sections in the gap region is proposed. In this cross section correction method, the average chord length of gap region is preserved to capture the effect of increased gap width. The validity of the present method is confirmed by verification calculations in a single assembly and 5 × 5 assembly geometries using the GENESIS code, which is a transport code based on the method of characteristics.     

Revealing the Dynamics of Hybrid Metal Halide Perovskite Formation via Multimodal In Situ Probes

The exploration of the synthetic space of halide perovskites hinges on an enormous number of parameters requiring time‐consuming experimentation to decouple and optimize. Here, the formation of the prototype material CH₃NH₃PbI₃ (MAPbI₃) is investigated at different time and length scales using multimodal in situ measurements to monitor the evolution of crystalline phases, morphology, and photoluminescence as a function of the lead precursors. Kinetically fast formation of crystalline precursor phases already during the spin‐coat deposition is observed using lead iodide (PbI₂) or lead chloride (PbCl₂) routes. These precursor phases most likely template final MAPbI₃ film morphology. In particular, the emergence of the “needle‐like” structure is shown to appear before film annealing. In situ photoluminescence measurements suggest nanoscale nucleation followed by rapid nuclei densification and growth. Using this multimodal in situ approach, different formation pathways can be identified either via precursor phases in the PbI₂ and PbCl₂ routes or direct perovskite formation from molecular building blocks as observed in the lead acetate (PbAc₂) route. Correlation of in situ results with photovoltaic device performance demonstrates the power of in situ multimodal techniques, paves the way to a fast screening of synthetic parameters, and ultimately leads to controlled synthetic procedures that yield high‐efficiency devices.     

Rafting-Enabled Recovery Avoids Recrystallization in 3D-Printing-Repaired Single-Crystal Superalloys

The repair of damaged Ni-based superalloy single-crystal turbine blades has been a long-standing challenge. Additive manufacturing by an electron beam is promising to this end, but there is a formidable obstacle: either the residual stress and γ/γ ′ microstructure in the single-crystalline fusion zone after e-beam melting are unacceptable (e.g., prone to cracking), or, after solutionizing heat treatment, recrystallization occurs, bringing forth new grains that degrade the high-temperature creep properties. Here, a post-3D printing recovery protocol is designed that eliminates the driving force for recrystallization, namely, the stored energy associated with the high retained dislocation density, prior to standard solution treatment and aging. The post-electron-beam-melting, pre-solutionizing recovery via sub-solvus annealing is rendered possible by the rafting (i.e., directional coarsening) of γ ′ particles that facilitates dislocation rearrangement and annihilation. The rafted microstructure is removed in subsequent solution treatment, leaving behind a damage-free and residual-stress-free single crystal with uniform γ ′ precipitates indistinguishable from the rest of the turbine blade. This discovery offers a practical means to keep 3D-printed single crystals from cracking due to unrelieved residual stress, or stress-relieved but recrystallizing into a polycrystalline microstructure, paving the way for additive manufacturing to repair, restore, and reshape any superalloy single-crystal product.     

Unsteady behavior and control of vortices in centrifugal compressor

Two examples of the use of vortex control to reduce noise and enhance the stable operating range of a centrifugal compressor are presented in this paper.In the case of high-flow operation of a centrifugal compressor with a vaned diffuser,a discrete frequency noise induced by interaction between the impeller-discharge flow and the diffuser vane,which appears most notably in the power spectra of the radiated noise,can be reduced using a tapered diffuser vane（TDV） without affecting the performance of the compressor.Twin longitudinal vortices produced by leakage flow passing through the tapered portion of the diffuser vane induce secondary flow in the direction of the blade surface and prevent flow separation from the leading edge of the diffuser.The use of a TDV can effectively reduce both the discrete frequency noise generated by the interaction between the impeller-discharge flow and the diffuser surface and the broadband turbulent noise component.In the case of low-flow operation,a leading-edge vortex（LEV） that forms on the shroud side of the suction surface near the leading edge of the diffuser increases significantly in size and blocks flow in the diffuser passage.The formation of an LEV may adversely affect the performance of the compressor and may cause the diffuser to stall.Using a one-side tapered diffuser vane to suppress the evolution of an LEV,the stable operating range of the compressor can be increased by more than 12 percent,and the pressure-rise characteristics of the compressor can be improved.The results of a supplementary examination of the structure and unsteady behavior of LEVs,conducted by means of detailed numerical simulations,are also presented.     

Fabrication, microstructure, and mechanical properties of tin nanostructures

Vertically aligned, cylindrical tin nanopillars have been fabricated via an electron beam lithography and electroplating method. Characterization by a non-destructive synchrotron X-ray microdiffraction (μSXRD) technique revealed that the tin nanostructures are body-centered tetragonal and are likely single-crystalline, or consist of a few large grains. The mechanical properties of tin nanopillars with average diameters of 920 nm, 560 nm, and 350 nm were studied by uniaxial compression in a nanoindenter outfitted with a flat punch diamond tip. The results of compression tests reveal strain rate sensitivity for nanoscale tin deformation, which matches closely to the previously reported bulk tin values. However, unlike bulk, tin nanopillars exhibit size-dependent flow stresses where smaller diameter specimens exhibit greater attained strengths. The observed size-dependence matches closely to that previously reported for single-crystalline face centered cubic metals at the nanoscale. μSXRD data was used to compare the dislocation density between as-fabricated and deformed tin nanopillars. Results of this comparison suggest that there is no measurable accumulation of dislocations within deformed tin nanopillars.