Graded evolution of anisotropic microstructure during sintering from crystal-oriented powder compact

Anisotropic sintering, including shrinkage and grain growth, was examined for c-axis-oriented (Sr,Ca)₂NaNb₅O₁₅ (SCNN) ceramics, which were prepared by colloidal processing under a magnetic field. In the c-axis-oriented SCNN powder compact, shrinkage and grain growth along the c-axis were higher than those along the a-axis. The anisotropic microstructural development was clearly associated with anisotropic sintering shrinkage. X-ray diffraction, scanning electron microscopy, and energy back scattering diffraction showed that the grain growth of oriented particles by including random grains contribute to the development of the oriented microstructure. Finally, the highly crystal-oriented SCNN ceramics with a densified microstructure were obtained through anisotropic sintering. These results clearly showed the potential to develop a well-defined anisotropic microstructure during sintering by designing and controlling the particle packing structure in a powder compact.     

Vapor absorption by LiBr aqueous solution in vertical smooth tubes

Heat and mass transfer in a falling film vertical in-tube absorber was studied experimentally with LiBr aqueous solution. The presented results include the effect of solution flow rate, solution subcooling and cooling water temperature on the absorption in a smooth copper tube 16.05 mm I.D. and 400 mm long. The experimental data in the previous report for a 1200-mm-long tube was also re-examined and compared. It was demonstrated by the observation of the flow in the tube that the break down of the liquid film into rivulets leads to deterioration of heat and mass transfer at lower film Reynolds number or in longer tubes. An attempt to evaluate physically acceptable heat and mass transfer coefficients that are defined with estimated temperature and concentration at the vapor–liquid interface was also presented.     

Preparation of SiC particles coated with alumina hydrate: Effect of reaction condition on particle coalescence

Alumina-hydrate-coated SiC particles were prepared via a homogeneous precipitation method using urea, and the conditions for uniform coating and less coalescence of the particles were investigated. Coalescence of coated particles could be said to occur by collision and agglomeration followed by deposition of alumina hydrate on the agglomerated particles. Coalescence of coated particles was suppressed by use of low reaction temperature, low concentration of aluminium sulfate, high concentration of urea, intensive stirring, and a flow reactor.     

Preparation of pyrochlores. A1−xHxTaO3·nH2O (A=Na,K)

Pyrochlores of A_1?xH_xTaO₃·nH₂O (A=Na,K) were prepared under the hydrothermal conditions. The values of x for these compounds were increased from 0.3 to 0.5 for A=Na and from 0.2 to 0.5 for A=K by treatment with the distilled water. The compounds with x<0.5 were decomposed to a mixture of NaTaO₃ and Na₂Ta₄O₁₁ for A=Na, or to a mixture of KTaO₃ and a tetragonal tungsten bronze phase, and those with x=0.5 to a single phase of A₂Ta₄O₁₁ at elevated temperatures. Below the decomposition temperatures, defect pyrochlores with oxygen vacancies, $\text{A}{}_{\mathrm{<mtext>1?</mtext><mtext>x</mtext>}}\text{TaO}{}_{\mathrm{<mtext>3?</mtext><mtext>x</mtext><mtext>2</mtext>}}$, were produced. They were hygroscopic, and in the case of A=K and x=0.5 the original phase was recovered by leaving in air for several hours.     

Evaluation of advanced fuzzy logic PSS on analog network simulatorand actual installation on hydro generators

This paper presents the experimental evaluation of an advanced fuzzy logic PSS on the analog network simulator at the Research Laboratory of Kyushu Electric Power Co., Inc. The proposed power system stabilizer (PSS) is set up by using a personal computer with A/D and D/A conversion interfaces. The personal computer based PSS was set on the analog network simulator to evaluate the effectiveness of the advanced fuzzy logic control scheme, and to provide sufficient data for the actual installation of the proposed PSS on hydro-units in the Kyushu Electric Power System. This paper also describes the actual installation of the proposed PSS on hydro-units in the Kyushu Electric Power System for the long term evaluation of the proposed PSS using its prototypes     

Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

Experimental study on a quasi-optical mode converter for transforming the whispering-gallery mode into a circularly polarized hollow radiation beam

An experiment was carried out for transforming the 120 GHz-TE_12.2 whispering-gallery mode (WGM) into a circularly polarized hollow radiation beam. A hollow beam was formed by reflecting the WGM, which was radiated from a 16 mm radius circular waveguide cut, with an annular mirror having suitable local normal vectors. The experimentally observed field intensity profiles of the reflected wave were in good agreement with calculated results.     

Measurement of the thermal diffusivity of thin films on substrate by the photoacoustic method

Measurements of the thermal diffusivity of thin films on substrate have been performed by the photoacoustic method. In order to examine the method we have built a new apparatus and proposed (1) a system calibration procedure using optically and thermally thick reference samples and (2) a data analysis procedure based on the RG (Rosencwaig and Gersho) theory. As a result of using a transparent photoacoustic cell, the systematic errors which are caused by stray light have been reduced. With this apparatus, measurements have been performed on platinum, titanium, and stainless steel (SUS304) thin foils (thickness form 50 to 100 µm) with three different liquid backing materials (water, glycerol, and ethyl alcohol). The reproducibility was within ±7% regardless of film thickness and substrate materials.     

66/77-kV C-GIS using composite insulation in SF6 gas

A second-generation model of cubicletype gas-insulated switchgear (C-GIS) with composite insulation incorporating SF₆ gas has been developed. The design does not require a gas process in field assembly; it has high reliability and its installation is more rapid; and a further reduction in size is achieved. The design principles are described in detail.