Technological Aspects of Synthesizing Ceramic Coatings by Flow-Through Micro-Arc Oxidation

Refractories and Industrial Ceramics - The paper introduces a promising technology for utilizing a traditional scheme for implementing a flow-through micro-arc oxidation method to restore localized...     

Experimental investigation of unconfined spherical and cylindrical flame propagation in hydrogen-air mixtures

This paper presents results of experimental investigations on spherical and cylindrical flame propagation in pre-mixed H₂/air-mixtures in unconfined and semi-confined geometries. The experiments were performed in a facility consisting of two transparent solid walls with 1 m² area and four weak side walls made from thin plastic film. The gap size between the solid walls was varied stepwise from thin layer geometry (6 mm) to cube geometry (1 m). A wide range of H₂/air-mixtures with volumetric hydrogen concentrations from 10% to 45% H₂ was ignited between the transparent solid walls. The propagating flame front and its structure was observed with a large scale high speed shadow system. Results of spherical and cylindrical flame propagation up to a radius of 0.5 m were analyzed. The presented spherical burning velocity model is used to discuss the self-acceleration phenomena in unconfined and unobstructed pre-mixed H₂/air flames.     

Fault trees—Problems and the modern state of investigations

Published in Kibernetika i Sistemnyi Analiz, No. 3, pp. 128–150, May–June, 1994.     

Synthesis and Composition of Compounds Containing the B10H- 11 Anion

The compounds MB₁₀H₁₁ (M = Me₄N⁺, Et₄N⁺, Bu₄N⁺, Ph₄P⁺, Ph₄As⁺) are synthesized. A procedure is proposed for boron determination by atomic absorption spectrophotometry, using microwave processing for sample preparation.     

Fabrication of Strain-Relaxed Si<Subscript>1 − <Emphasis Type="Italic">x</Emphasis></Subscript>Ge<Subscript>x</Subscript>/Si(001) Buffer Layers of Low Surface Roughness

The results are presented of the fabrication of strain-relaxed graded Si_{1 − x} Ge_x/Si(001) buffer layers with a maximum Ge fraction of about 0.25 that have a low density of threading dislocations (<10⁶ cm⁻²) and low surface roughness. The buffer layers are grown by atmospheric-pressure hydride CVD. It is found that chemical mechanical polishing can reduce their surface roughness to a level comparable with that of the original Si(001) substrates. It is shown that the polished buffer layers can serve as substrates for MBE-grown SiGe/Si heterostructures.__________Translated from Mikroelektronika, Vol. 34, No. 4, 2005, pp. 243–250.Original Russian Text Copyright © 2005 by Vostokov, Drozdov, Krasil’nik, Kuznetsov, Novikov, Perevoshchikov, Shaleev.     

Electromagnetic wave reflection from Fe/Cr nanostructures

The reflection of electromagnetic waves in the millimeter wave band from Fe/Cr nanostructures has been studied. It is established that the giant magnetoresistance (GMR) in the nanostructure leads to an increase in the reflection and a decrease in the transmission of microwaves, while the magnetic resonance leads to a decrease in both the reflection and transmission coefficients.     

Development of improved methods for type testing present day mediumvoltage circuit breakers for outdoor service

Type testing for fault currents for medium-voltage circuit breakers rated at 15 kV to 72.5 kV is addressed. The ANSI designation of a new class of definite-purpose circuit breakers capable of switching transformer secondary faults and the introduction of the requirement for short-line-fault tests for breakers rated 72.5 kV and below have increased the difficulty of performing type tests in a testing laboratory. It is concluded that synthetic testing using the parallel current injection circuit is described in ANSI C37.081 provides the best available method for proving these complex requirements for medium-voltage circuit breakers     

Surface electronic structure of detonation nanodiamonds after oxidative treatment

X-ray absorption spectroscopy has been used for comparative study of electronic structure of detonation nanodiamonds (ND) purified using different oxidative treatments. The treatment of detonation soot with a mixture of nitric and sulphuric acids followed by ion exchange and ultrafiltration of hydrosol obtained was found to result in developing of ND surface coverage consisting of oxidized carbon species, which electronic state is close to that of strongly oxidized graphite. The deeper purification of ND was demonstrated to allow cleaning of ND particles from most of the oxidized carbon contaminations.