Low Electrical Percolation Threshold of Silver and Copper Nanowires in Polystyrene Composites

Silver and copper nanowires have been synthesized using a scalable method of AC electrodeposition into porous aluminum oxide templates, which produces gram quantities of metal nanowires ca. 25 nm in diameter and up to 5 and 10 μm in length for Ag and Cu, respectively. The nanowires have been used to prepare polystyrene nanocomposites by solution processing. Electrical resistivity measurements performed on polymer nanocomposites containing different volume fractions of metal indicate that low percolation thresholds of nanowires are attained between compositions of 0.25 and 0.75 vol %.     

Cell cycle and genetic requirements of two pathways of nonhomologous end-joining repair of double-strand breaks in Saccharomyces cerevisiae

In Saccharomyces cerevisiae, an HO endonuclease-induced double-strand break can be repaired by at least two pathways of nonhomologous end joining (NHEJ) that closely resemble events in mammalian cells. In one pathway the chromosome ends are degraded to yield deletions with different sizes whose endpoints have 1 to 6 bp of homology. Alternatively, the 4-bp overhanging 3' ends of HO-cut DNA (5'-AACA-3') are not degraded but can be base paired in misalignment to produce +CA and +ACA insertions. When HO was expressed throughout the cell cycle, the efficiency of NHEJ repair was 30 times higher than when HO was expressed only in G1. The types of repair events were also very different when HO was expressed throughout the cell cycle; 78% of survivors had small insertions, while almost none had large deletions. When HO expression was confined to the G1 phase, only 21% were insertions and 38% had large deletions. These results suggest that there are distinct mechanisms of NHEJ repair producing either insertions or deletions and that these two pathways are differently affected by the time in the cell cycle when HO is expressed. The frequency of NHEJ is unaltered in strains from which RAD1, RAD2, RAD51, RAD52, RAD54, or RAD57 is deleted; however, deletions of RAD50, XRS2, or MRE11 reduced NHEJ by more than 70-fold when HO was not cell cycle regulated. Moreover, mutations in these three genes markedly reduced +CA insertions, while significantly increasing the proportion of both small (-ACA) and larger deletion events. In contrast, the rad5O mutation had little effect on the viability of G1-induced cells but significantly reduced the frequency of both +CA insertions and -ACA deletions in favor of larger deletions. Thus, RAD50 (and by extension XRS2 and MRE11) exerts a much more important role in the insertion-producing pathway of NHEJ repair found in S and/or G2 than in the less frequent deletion events that predominate when HO is expressed only in G1.     

Outcome of different treatment mixes in a multidimensional neuropsychological rehabilitation program.

Within a clinical demonstration program, 59 traumatically brain-injured patients were treated with 1 of 3 mixes of treatment. Mix 1 included cognitive remediation (CGR), small-group interpersonal (SGI) communication training, therapeutic community activities, and personal counseling. Mix 2 was similar to Mix 1 but stressed SGI exercises and eliminated CGR. Mix 3 emphasized CGR and eliminated SGI exercises. The efficacy of the treatment mixes was evaluated with performance on neuropsychological tests, improved independence in functional activities, measures of intra- and interpersonal functioning, and vocational outcome. Ss' participation in the program, irrespective of treatment mix, yielded improvements in (1) self-image, (2) quality of interpersonal relatedness and interaction, (3) involvement with others in naturalistic settings, and (4) vocational outcome. Overall, data point to the superiority of the balanced mix (Mix 1) over Mixes 2 and 3. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Criteria for judging the admissibility of eyewitness testimony of long past events.

Court cases of recovered memories of childhood abuse, in which the victim's testimony may constitute the only evidence available, and a growing body of research demonstrating the inexactitude and suggestibility of autobiographical memory of long past events, are forcing courts and cognitive scientists to seek scientific, principled criteria for admissibility of such testimony. The authors use as examples 2 recent court cases. In the 1st case, a concussion produced total retrograde amnesia for an accident for a period of 3 years, and then, over a few months, the driver claimed his memory returned. In the 2nd, 2 adults reported to the police that they witnessed their sister's murder 35 years earlier, when they were 3 and 5 years old, respectively. The authors provide objective guidelines for courts to determine whether testimony about recovered or very-long-term memory for eyewitnessed events should be admissible. The principles outlined can be expanded easily to include eyewitness testimony in general. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

An engineering study of the film embossing process

A mathematical model of the dynamics and heat transfer of the film embossing process has been developed. The thermal analysis around the preheat roll is determined from an unsteady, two-dimensional heat conduction equation along with appropriate boundary conditions by neglecting the curvature of the preheat roll and choosing a Lagrangian reference frame. The heat transfer occurring between the preheat roll and the embossing rolls is based on a one-dimensional analysis, including both convective and radiative effects. The deformation occurring in the nip region is analyzed for two different situations. For the case where the surface features are small in comparison with the film thickness, a modified one-dimennsional calendering analysis is given, accounting for the irregular geometry of the embossing roll surface. For the case where the polymer does not make complete contact with the surface of the engraved channel, the local deformation is determined by means of a simple one-dimensional cavity filling model. The required pressure distribution is determined by means of a simple one-dimensional cavity filling model, The required pressure distribution is determined by means of a conventional calendering analysis. The analysis for the case of a Newtonian and power-law model is presented in detail. The model yields qualitatively correct results and is computationally simple.     

Tool wear monitoring using neuro-fuzzy techniques: a comparative study in a turning process

Tool wear detection is a key issue for tool condition monitoring. The maximization of useful tool life is frequently related with the optimization of machining processes. This paper presents two model-based approaches for tool wear monitoring on the basis of neuro-fuzzy techniques. The use of a neuro-fuzzy hybridization to design a tool wear monitoring system is aiming at exploiting the synergy of neural networks and fuzzy logic, by combining human reasoning with learning and connectionist structure. The turning process that is a well-known machining process is selected for this case study. A four-input (i.e., time, cutting forces, vibrations and acoustic emissions signals) single-output (tool wear rate) model is designed and implemented on the basis of three neuro-fuzzy approaches (inductive, transductive and evolving neuro-fuzzy systems). The tool wear model is then used for monitoring the turning process. The comparative study demonstrates that the transductive neuro-fuzzy model provides better error-based performance indices for detecting tool wear than the inductive neuro-fuzzy model and than the evolving neuro-fuzzy model.     

Source identification of plant-wide faults based on k nearest neighbor time delay estimation

The identification of plant-wide faults is a very important topic as it enables plant operators to decrease rejections or to increase the product quality. This paper shows a fault propagation approach for this field of interest based on time delay estimation. Due to the fact that the estimation of time delays in multiple-input single-output systems or nonlinear systems is either impossible or very difficult with known methods, a new method based on k nearest neighbor imputation was developed and is validated in this paper theoretically. The effectiveness of the identification algorithm is demonstrated on several simulations and on an industrial hydrocracker plant.     

Effect of Alumina on the Structure and Mechanical Properties of Spark Plasma Sintered Boron Carbide

Uniform densification of relatively thick (~7 mm) consolidated boron carbide plates at relatively low temperatures (e.g. 1800°C) and low facture toughness are two of the primary challenges for further development of boron carbide applications. This work reports that these two challenges can be overcome simultaneously by adding 5 wt% alumina as a sintering aid. Nearly fully dense (97%), fine grained boron carbide (B₄C) samples were produced using spark plasma sintering at 1700°C and above in the B₄C‐5 wt% Al₂O₃ system. The alumina and boron carbide matrix reacted to form an Al₅O₆BO₃ (a mullite‐like phase) during sintering. The Al₅O₆BO₃ phase facilitated uniform densification via liquid phase sintering. This secondary phase is dispersed throughout the intergranular pores, providing obstacles for crack propagation and resulting in tougher boron carbide ceramics.     

Synthese von 6-(pyrid-4-yl)-substituierten Pyrido[: 3-d]pyrimidinen und 1,8-Naphthyridinen

Synthesis of 6-(4-pyridinyI)-substituted Pyrido[2,3-d]pyrimidines and 1,8-Naphthyridinms A series of new 6-(4-pyridinyl)-substituted pyrido-[2,3-d]pyrimidines 2 – 4 and 1,8-naphthyridines 6 , respectively, is described. Cyclisation of 2-amino-5-(4-pyridinyl)-pyridinm-3-carboxamide 1a with diethyl oxalate gives the pyrido-[2,3-d]pyrimidinm 2a . Alkylation of( 2a ) yields the 3-ethylaminoxyrido[2,3-d]pyrimidine derivative 2b . Saponification of 2a , b gives the corresponding carboxylic acids 3a , b , which are decarboxylated by heating above the melting point to give 4a , b . The 2-amino-5-(4-pyridinyl)-pyridinm carboxylic acid derivatives 1 b – e react with ethylmalonylchloridm and diethyl malonate to afford the 1,8-naphthyridines 6b – e . The 1-oxide 7 in a similar reaction gives 8 and the oxdiazole( 9 ) which is converted by ring transformation to the 1,8-naphthyridine 10 .     

Personal resources and political uprooting: The Israeli experience.

The authors assessed distress in Israeli society before and after Israel’s disengagement from Gaza and the northern West Bank during the summer of 2005. Random samples of 701 Israelis residing in various parts of Israel (Study 1) and 246 Israelis residing in Gaza and the northern West Bank who were to be uprooted (Study 2) were interviewed by telephone several weeks before the disengagement (T1), with 462 and 124 of these respondents, respectively, reinterviewed several weeks after the disengagement (T2). Anxiety related to the national and security situation was lower at T2 than at T1 in both studies. A personal resource, namely mastery–optimism, contributed negatively to both anxiety and hostility before the disengagement in both studies. In Study 1, it also predicted lower postdisengagement anxiety. The findings underscore the importance of mastery–optimism in the adjustment to threatening political events such as forced uprooting. (PsycINFO Database Record (c) 2010 APA, all rights reserved)