Detection of Multiple Blockages in Parallelized Microreactors

In a plant consisting of parallelized microreactors (MRs), the product quality is lowered because of a lack of flow uniformity among them when blockage occurs. It is not practical to install sensors in every MR from the viewpoint of cost when detecting the blocked MRs. In the previous study, the multiple blockage detection (MBD) method using a small number of sensors was proposed, but its performance became low when the number of sensors decreased. Here, the conventional algorithm for MBD is improved by considering the process behavior on blockage occurrence, and the effectiveness of the improved algorithm is demonstrated through a numerical case study. The effects of flow distributor types and sensor types on the MBD performance are numerically investigated.     

Phase fluctuations of cross-polarized signals at 4 GHz in fine weather on earth-space paths

On an earthspace propagation path with the low elevation angle of 10 deg, the phase between co- and crosspolar signals occasionally showed rapid and irregular fluctuations during fine weather. These fluctuations were generally significant during the daytime, and were strongly in phase with the occurrence of the copolar amplitude scintillations. This could be attributed to the combined effects of the crosspolar phase pattern of the receiving antenna and small fluctuations of the angle of arrival of the radiowaves.     

Preparation of micrometer‐sized,monodisperse, magnetic polymer particles

Micrometer‐sized, monodisperse, magnetic composite particles were prepared by heating micrometer‐sized, monodisperse, hollow polystyrene/polydivinylbenzene composite polymer particles at 200°C for 4 h (particles had been dipped in pentacarbonyliron) and then washed in 12 N HCl and water. The hollow polymer particles were produced by seeded polymerization by the dynamic swelling method that was proposed by authors. The magnetic composite particles contained Fe₃O₄, the content of which was 49% based on total weight, and were attracted easily in water by a 1650 G magnet. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 428–433, 2003     

Extensions of polyacrylic acid ammonium salts in the adsorption layer to fluidize alumina slurries

An average shell volume occupied in the adsorption layer on alumina by a polyacrylic acid ammonium salts molecule (PAA) defined as the average area occupied by an adsorbed PAA on alumina multiplied by the average thickness of the water layer at the limit of thickening, has been calculated from the adsorbed amount of PAA and from the flow points of alumina in the presence of PAA of different molecular weights. A steric effect of the PAA dispersant on the dispersion of alumina resulted in a flow with no yield stress. This was due to the change of the extension of PAA in the adsorption shell from a sphere to an ellipsoid with a long axis which exceeded the effective distance that the van der Waals attraction force reaches at a molecular weight for the PAA of between 10 000–20 000.     

Hydroliquefaction of low-sulfur coals using iron carbonyl complexes—Sulfur as catalysts

Hydroliquefaction of low-sulfur Australian coals (Wandoan and Yallourn) was studied using iron carbonyl complexes as catalyst. The addition of Fe(CO)₅ (2.8 wt% Fe of coal) increased coal conversion from 48.6 to 85.2% for Wandoan coal, and from 36.7 to 69.7% for Yallourn coal in 1-methylnaphthalene at 425°C under an initial hydrogen pressure of 50 kg cm^?2. When molecular sulfur was added to iron carbonyls (Fe(CO)₅, Fe₂(CO)₉ and Fe₃(CO)₁₂), higher coal converions ( > 92%) and higher oil yields (>46%) were obtained, along with an increase in the amount of hydrogen transferred to coal from the gas phase (0.2 to 2.8%, d.a.f. coal basis). In the liquefaction studies using a hydrogen donor solvent, tetralin, Fe(CO)₅S catalyst increased the amount of hydrogen absorbed from the gaseous phase and decreased the amount of naphthalene dehydrogenated from tetralin. The direct hydrogen transfer reaction from molecular hydrogen to coal fragment radicals seems to be a major reaction pathway. Organic sulfur compounds, dimethyldisulfide and benzothiophene, and inorganic FeS₂ and NiS were found to be good sulfur sources to Fe(CO)₅. From X-ray diffraction analyses of liquefaction residues, it is concluded that Fe(CO)₅ was converted into pyrrhotite (Fe_1?xS) when sulfur was present, but into Fe₃O₄ in the absence of sulfur.     

Effects of partial recrystallization on high-cycle fatigue deformation and crack generation of a nitrogen-strengthened 32Mn-7Cr austenitic steel at liquid-nitrogen temperature

To achieve higher fatigue resistance against subsurface crack generation, both the refinement of grain structure and the introduction of mobile dislocations on various slip systems have been shown to be effective in the 32Mn-7Cr austenitic steel. A novel treatment which consisted of cold grooved rolling and partial recrystallization was introduced to modify the microstructure. High-cycle fatigue properties and fatigue-crack generation were investigated for both the solution-treated (ST) and the partially recrystallized (PR) materials at 77 K. The PR material displayed higher fatigue strength than the ST material, especially in the high-cycle regime. No subsurface crack generation was detected for the PR material; however, it appeared in the lower peak stress and/or in the longer-life range for the ST material. Intergranular facets formed a subsurface crack initiation site in the ST material. Since the dislocation structure that developed in the fatigued PR material assisted homogeneous and multidirectional plastic deformation, the localized deformation and/or the stress concentration at the grain boundaries by coplanar arrays were believed to be relieved. Therefore, intergranular cracking due to incompatibility at a grain boundary may disappear.     

Present status and future prospects of PV activities in Japan

The photovoltaic (PV) power systems in Japan made great strides in the past decade. The PV industry in the 1990s greatly depended on the research projects and dissemination programs carried out by the Ministry of International Trade and Industry. However, the industrial structure for full-scale deployment of the PV system is currently being established by the manufacturers’ continuous efforts to reduce the PV system cost and the government’s consecutive supports to create the initial market. It is expected that the synergetic effect of the cost reduction and incentives for introduction will activate the PV industry and its market more and more toward achieving 5000 MW of the capacity in FY 2010.     

The combined method: a novel access technique for fetal endoscopic surgery

BACKGROUND/PURPOSE: To develop practical and less invasive techniques for fetal endoscopic surgery, new methods of lifting the uterine wall to allow fetal surgery without maternal laparotomy were developed and assessed. METHODS: Fetal endoscopic surgical procedures, including tracheostomy and umbilical vascular cannulation, were performed using one of the three methods to enter the uterus without maternal laparotomy in pregnant goats (n = 6; 105 to 115 days' gestation): (1) direct uterine lifting with an air-cushion device; (2) indirect uterine lifting, in which the uterine wall was fixed to the maternal abdominal wall using balloon tip ports inserted percutaneously by Seldinger's method, then the maternal abdomen was lifted mechanically; and (3) combined method, in which low pressure CO2 (5 mm Hg for initial inflation and 2 mm Hg for maintenance) was insufflated into the uterus in addition to the indirect uterine lifting cited above. RESULTS: The direct uterine lifting caused massive injury of myometrium and uterine membranes. The creation of intrauterine space and the protection of the membranes were not accomplished effectively by the indirect uterine lifting only. The combined method provided the adequate intrauterine space and excellent endoscopic visibility for completion of the endoscopic procedures with minimal uterine injury. CONCLUSION: The fetal endoscopic surgery may be accomplished simply and safely by the combined method, a novel technique of uterine lifting to allow fetal surgery without maternal laparotomy.     

Preparation of spherical fine ZnO particles by the spray pyrolysis method using ultrasonic atomization techniques

An ultrasonic atomizer was used in the spray pyrolysis method to prepare fine, spherical and uniform ZnO particles. Almost spherical particles were obtained successfully which had a mean particle size of 0.15 m and had a very narrow particle size distribution. By using alcohol as the solvent, it was found that the particles do not have hollow shell layers which could usually be observed in the spray pyrolysis process by using water as the solvent. The morphology of the ZnO particles was strongly affected by the concentration of the starting solution.