Factors affecting the mechanical properties of mica-filled polypropylenes

Water-ground Phlogopite mica (Kemira Siilinjarvi phlogopite) has been evaluated as a reinforcing filler in polypropylene. The major factors which influence the composite strength and modulus include the size, aspect ratio, and uniformity of the mica flakes. Aqueous delamination permits the production of very small flakes (less than 44 microns diameter) with aspect ratios near 50. Such small flakes impart greater tensile and modulus values to polypropylene than larger flakes and the former can also be reprocessed many times without any deterioration of properties. Surface treatment is necessary for adequate dispersion and coupling, particularly with the finely divided mica fillers. Other properties such as the heat-distortion temperature, fracture toughness, and gas permeability are also influenced by the mean size and aspect ratio of the mica filler. Guidelines are presented to indicate the preferred characteristics of mica fillers for optimum performance.     

C,CO and CO2 hydrogenation on cobalt foil model catalysts: evidence for the need of CoO reduction

The hydrogenation of C, CO, and CO₂ has been studied on polycrystalline cobalt foils using a combination of UHV studies and atmospheric pressure reactions in temperature range from 475 to 575 K at 101 kPa total pressure. The reactions produce mainly methane but with selectivities of 98, 80, and 99 wt% at 525 K for C, CO, and CO₂, respectively. In the C and CO₂ hydrogenation the rest is ethane, whereas in CO hydrogenation hydrocarbons up to C₄ were detected. The activation energies of methane formation are 57, 86, and 158 kJ/mol from C, CO, and CO₂, respectively. The partial pressure dependencies of the CO and CO₂ hydrogenation indicate roughly first order dependence on hydrogen pressure (1.5 and 0.9), negative first order on CO (–0.75) and zero order on CO₂ (–0.05). Post reaction spectroscopy revealed carbon deposition from CO and oxygen deposition from CO₂ on the surface above 540 K. The reduction of cobalt oxide formed after dissociation of C-O bonds on the surface is proposed to be the rate limiting step in CO and CO₂ hydrogenation.     

Extraction of protein from skim natural rubber latex using PEG as a surfactant via low speed centrifugation and continuous flow

Protein extractions from skim natural rubber latex using 3 %w/v polyethylene glycol (PEG6000) via both low speed centrifugation and continuous flow were investigated. In centrifugal extraction, when the speed was 1000 rpm, the extractable protein (EP) content in serum increased with processing time from 5 to 30 min and when the time was fixed at 5 min, EP content increased with centrifugal speed. In addition, further washing deproteinized chips with 2 %w/v SDS solution could remove proteins with efficiencies corresponding to the efficiencies of protein removals in latex phase, implying the role of PEG in protein reduction in both steps. In continuous flow extraction, EP content increased with increasing Reynolds number or increasing mean residence time of the flow to a maximum and then dropped. The efficiencies of the centrifugal extraction and continuous flow extraction were 55.2 and 33.7%, respectively. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39900.     

Blends of natural rubber and polyurethane latices studied by 1H wideline and 13C MAS solid‐state NMR

¹H wideline and ¹³C magic‐angle spinning NMR have been used to study the morphology and dynamics of latex‐cast and solution‐cast film blends of natural rubber (NR) and a polyurethane (PU) based on poly(?‐caprolactone) diol and isophorone di‐isocyanate. ¹H T₁ and T_1ρ relaxation times have been measured, and the extent of interpenetration of the NR and PU constituents has been monitored using the Goldman–Shen technique. The NMR spectra and relaxation properties indicated that the NR and PI constituents largely occupy separated domains on a distance scale of >10 nm. The Goldman–Shen experiments indicated that there was slightly greater contact between NR and PU in the solution‐cast samples than in the latex‐cast. The tensile properties of the films have been measured. The tensile strength and initial Young's modulus pass through a maximum at a PU content of about 50 wt%. © 2002 Society of Chemical Industry     

Stable SOI micromachined electrostatic AC voltage reference

We have designed and manufactured a micromachined moving plate capacitor to be used as an AC voltage reference in electrical metrology. The reference is based on the characteristic AC current–voltage curve of the component having a maximum, the value of which ideally depends only on the geometry of the component and material properties of single crystalline silicon. The electrode surface stability is essential in this application and hence a new fabrication process has been developed to metallize both surfaces of an electrostatically actuated micromachined structure. The stability of the AC reference voltage at a frequency of 100 kHz and an RMS voltage value 6.4 V was measured to be ±60 ppm over 14 h.     

Environment Analysis as a Basis for Designing Multimodal and Multidevice User Interfaces

In this article, we present a practical approach to analyzing mobile usage environments. We propose a framework for analyzing the restrictions that characteristics of different environments pose on the user's capabilities. These restrictions along with current user interfaces form the cost of interaction in a certain environment. Our framework aims to illustrate that cost and what causes it. The framework presents a way to map features of the environment to the effects they cause on the resources of the user and in some cases on the mobile device. This information can be used for guiding the design of adaptive and/or multimodal user interfaces or devices optimized for certain usage environments. An example of using the framework is presented along with some major findings and three examples of applying them in user interface design.     

Fabrication and Characterization of Large Free-Standing Polarizer Grids for Millimeter Waves

Construction of large aperture free-standing metal wire grids is demonstrated for the lower end of the millimeter wave spectral region. For the constructed two grids the co-polarized and cross-polarized components of transmitted power were measured at 45° oblique incidence. The measurements were performed as a function of wire orientation angle and in more detail at selected angles. The results are in good agreement with the theoretical results presented in the literature. In order to save time and costs the construction apparatus was simplified from those reported previously by other authors. It was shown that for this frequency range the grid characteristics are not degraded when such an apparatus is applied. One of the constructed grids will be used in a calibration system of the Helsinki University of Technology (HUT) polarimetric radiometer.     

Optimal proportion of studded tyres in traffic flow to prevent polishing of an icy road

Studded tyres can significantly wear the road surface and increase particle emissions from the road surface, which has a negative impact on air quality in urban areas. However, road wear might have a positive aspect by roughening the road surface and thus preventing polishing. As a consequence, other vehicles than the ones using studded tyres might also benefit from the usage of studded tyres. The impact of the proportion of studded tyres in the traffic flow on the tyre–ice friction coefficient was studied with a fleet of real cars in a closed environment under strict procedural control. The results show that a proportion of 25–50% studded tyres in the traffic flow is enough to prevent ice from developing in a manner that is critically slippery for non-studded winter tyres. It was also observed that the visual appearance of the ice surface does not indicate if the ice has become more slippery or not.     

Variational formulation of open-ended coaxial line in contact withlayered biological medium

An open-ended coaxial probe designed to measure layered biological media is analyzed with a new method. The probe is considered as an electrostatic circuit element whose capacitance is solved using a stationary functional. The fundamental transverse electric and magnetic field (TEM)-mode and the series of evanescent wavemodes in the coaxial cable are used as basis functions. The field outside the probe is solved using a Hankel transform. The capacitance is calculated for homogeneous materials and two-layer structures and the results are compared with values measured with a phantom model. The method can be easily extended for structures with an arbitrary number of layers. A practical approximation for two-layer cases, originally developed to take into account the effect of subcutaneous fat in skin measurements, is presented and its validity for different combinations of dielectric constants and the thickness of the first layer is demonstrated. The static approximation limits the frequency range, but it covers biological measurements up to 500 MHz. The developed method is accurate and easy to adopt in practice