Design of high-speed data transfer turbo code for body channel communication transceivers

In this work, a digital differential transmitter based on low-power wireless compensation transceiver for body channel communication (BCC) is proposed. Further, the proposed transceiver is composed of Touch Status Detection Unit (TSDU), Wireless Status Compensation Unit (WSCU), and a reconfigurable preamplifier. Initially, the human body channel environment for wireless communication is investigated based on properties from 1 to 100 MHz. Further, the turbo code-based encoding scheme is used to encode the data before transferring the data on the transmitter side. Also, the proposed error-correcting parallel turbo decoder using a modified step-by-step algorithm is presented. The turbo code-based decoding scheme is used to recover the error-free transmitted data at the receiver side. Results demonstrate that the proposed BCC transceiver is designed using 90 nm CMOS technology and it is observed that the proposed BCC transceiver has utilized an area of 600mm². Also, the maximum data rate achieved by a proposed BCC transceiver was 100 Mbps, and the overall transceiver power consumption is 0.42 mW, and energy for communication is 0.02 nj/b.     

Numerical Simulation and Validation of Ozone Concentration Profile in Green Gram (Vigna radiate) Bulks

The new fumigant ozone offers an alternative to contact insecticides such as phosphine and methyl bromide as a grain fumigant. This study was carried out to test the flow characteristics of ozone from points of release to the available concentration of ozone to kill pests at other areas along the storage bin. A mass transfer model which predicts ozone concentration as a function of time was applied along with continuity equation to simulate the ozone transfer in a storage bin. Ozone exchange rate based on grain bed thickness was taken into account and evaluated using the correlation developed during the experiment. The relative error between the experimental and predicted ozone concentration values for the entire bin geometry was less than 25.7%. Overall, the general trends of measured ozone concentration were compatible with the simulated ones.     

In-vitro digestibility,textural and quality characteristics of ditalini pasta fortified with green banana flour and its type -IV modified starch

Resistant starch in unripe banana offers a possibility to alter the glycemic properties in convenience foods, such as pasta. In this study, pasta formulations were tried by replacing 30% semolina with varying proportions of green banana flour (GBF) and banana-modified starch (MS). The effect of substitution on physicochemical and functional properties, including in-vitro starch digestibility, antioxidant property and consumer acceptability, was evaluated. Among the composite flours, MS recorded higher swelling power and water holding capacity. The replacement of semolina with GBF resulted in higher resistant starch, 4–5 times enhanced indigestible fraction, phenols, flavonoids and antioxidant activity in pasta. Pronounced increment was also observed in potassium, calcium and magnesium content in blended pasta. Optimal cooking time was reduced with the addition of GBF, whereas it was enhanced with MS. GBF and MS in the blends, decreased the hydrolysis rate (up to 24%) and glycemic index (up to 17%) of pasta. However, the addition of MS beyond 10% negatively influenced springiness and chewiness. Microstructural studies explained the positive structural changes with the addition of GBF and MS. Sensory attributes disclosed that the addition of 25% GBF and 5% MS is a desirable proportion for pasta with a functional characteristics.     

Preparation of a functional nanofibrous polymer membrane incorporated with poly(2-aminothio phenol) stabilized gold nanoparticles

Functional nanofibrous polymer membranes were prepared by incorporating poly(2-aminothio phenol) (P2AT) stabilized Au NPs onto electrospun polyvinylidene fluoride (PVdF) nanofibers (designated as P2AT-Au NPs@PVdF-NFM). The preparation of P2AT-Au NPs@PVdF-NFM involves two steps: loading of 2AT (monomer) into electrospun PVdF nanofibrous membrane and polymerization of 2AT by gold chloride. P2AT and Au NPs were simultaneously formed into the electrospun PVdF-NFM. Transmission electron microscope image of P2AT-Au NPs@PVdF-NFM informs the presence of Au NPs (with sizes ~10 nm) onto PVdF-NFM.     

Electrical conduction in evaporated terbium fluoride thin films

The current-voltage characteristics of thin-film capacitors with evaporated terbium fluoride dielectric have been studied as a function of temperature (in the range 300 to 418 K). For sufficiently high electric fields (> 10⁴ V cm^–1, the leakage current is found to increase exponentially with the square root of the applied electric field. Analysis of the data suggests an electrode-limited mechanism such as that suggested by Schottky. It is seen that the conduction mechanism is an activated process with the activation energy decreasing with increasing field. Dielectric break-down and its dependence on film thickness have also been investigated. Break-down field strength follows the Forlani-Minnaja relation.     

Template-free mechanochemical route to prepare crystalline and electroactive polydiphenylamine nanostructures

A facile and sustainable mechanochemical route for the synthesis of undoped polydiphenylamine (PDPA) and inorganic acid doped nanostructures are reported. Field emission scanning electron microscopic (FESEM) images highlighted the formation of distinctly different nanostructures for each of the inorganic acid doped PDPA. Elemental analysis carried out for the polymers revealed the presence of more repeating units in their backbone. The X-ray diffraction (XRD) results of the as-prepared PDPA nanostructures indicated the high degree of crystallinity ever reported for PDPA. Spectroscopic profile of the polymers showed that the prepared PDPA is in a doped conducting form. Electrochemical studies performed for the polymeric particles ascertained the redox behaviour and the good electrochemical activity of obtained PDPA samples. The probable mechanistic aspect behind the formation of PDPA nanostructures through this simple and efficient route is discussed.     

Effect of imbibed moisture on monotonic and low-velocity impact behavior of injection over-molded short/continuous fiber reinforced polypropylene composites

Design of automotive components with over-molded short/continuous fiber reinforced thermoplastic composites necessitates understanding of their behavior under extreme outdoor conditions. The short, quasi-isotropic and over-molded short/continuous glass fiber reinforced polypropylene (PP) composite specimens were prepared as per standard and immersed in water until equilibration to study their relative moisture absorption characteristics and consequent mechanical behavior. As the absorbed moisture mostly occupied the interface between fiber and matrix in laminated composite inserts and moisture absorption of short fiber composite core is insignificant, the moisture absorption of over-molded composites is just above 50% of that of laminated composites. The flexural, interlaminar shear and impact behavior of equilibrated composites is primarily governed by the quantum of imbibed moisture of composite materials. Optical analysis of failed moisture equilibrated over-molded specimens showed a marginal delamination between plies of the inserts without any perceptible damage within the short fiber composite similar to dry as molded specimens.     

Effect of Fiber Bridging Stress on the Fracture Resistance of Silicon-Carbide-Fiber/Zircon Composites

The room-temperature fracture-resistance behavior ( R -curve) of unidirectional silicon-carbide-fiber-reinforced zircon-matrix composites has been studied experimentally and numerically. The composites showed strong rising R -curve behavior from experimental results that used in situ crack-length measurements taken via optical microscopy as well as the compliance method. A numerical calculation, based on the available models, then was performed to determine the bridging-stress function from the experimental R -curve. In addition, the effect of the residual stress and constituent properties on the bridging-stress function also has been considered in the numerical calculations. These results have indicated that the bridging-stress function, which controls the fracture resistance of ceramic composites, can be obtained from the carefully measured R -curve.     

Electrochemical synthesis and characterization of poly(aniline-co-1-amino-9,10-anthraquinone), a nanosized conducting copolymer

The electrochemical copolymerization of aniline (ANI) with 1-amino-9,10-anthraquinone (1-AAQ) was carried out in 4 M sulfuric acid by potential cycling in the potential range of −0.1 V to 1.3 V vs. SCE. Copolymer films were grown from different feed ratios of ANI and 1-AAQ (0.2:0.8, 0.4:0.6, 0.5:0.5, 0.6:0.4, 0.8:0.2) on a glassy carbon electrode (GCE). Studies on the effect of scan rate on the conductivity of the copolymer film confirmed the formation of a stable conducting copolymer film. The FTIR spectrum recorded for the copolymer film provides concrete evidence of copolymer formation, since it indicates the presence of quinone units in the copolymer backbone. XRD data (particle size: 47 nm) and SEM (grain size: 100 nm) micrographs provide a clear picture of the nano-sized polymeric particles formed. It is envisaged that the newly reported copolymer could be a useful material for performing the catalytic reduction of oxygen in an acidic medium—a useful process for fuel cell applications.