Effect of plating bath composition on chemical composition and oxygen reduction reaction activity of electrodeposited Pt–Co catalysts

Platinum–cobalt(Pt–Co) alloy electrocatalysts were prepared on pretreated carbon cloth by electrodeposition from different plating baths with the aim of finding suitable plating bath conditions that could control the chemical composition of the Pt–Co alloy electrodeposits over a wide range(from 0 to 100 at% Pt) and then to study the relationship of the deposit composition on the oxygen reduction reaction(ORR) electroactivity. The type of supporting electrolyte, the solution pH, Pt and Co concentrations of the plating bath and the current density used for electrodeposition all play a crucial role in the composition of the electrodeposited Pt–Co alloy. Pt contents in all the Pt–Co alloys deposited in H_2SO_4 are at a relatively high and narrow level(83 at%–97 at% Pt), regardless of the electrodeposition conditions used. While the Pt contents in the Pt–Co alloys deposited in Na_2SO_4 could reach a very low and broad level(5 at%–97 at% Pt), evidence of Co oxide formation is observed. Of the three supporting electrolytes studied, only NaCl effectively produces Pt–Co deposits over a wide range of compositions(8–90 at% Pt)by controlling the Pt and Co concentrations of the plating bath and using the high enough current density. The results show a qualitative correlation between Pt–Co deposit composition and ORR activity, where Pt–Co alloy catalysts with ≥ 45 at% Pt tend to yield higher ORR activities than the pure Pt catalyst, with the best ORR performance obtained from the Pt–Co alloy catalyst with 78 at% Pt.     

Lipase-catalyzed synthesis of hydrophobically modified dextrans: activity and regioselectivity of lipase from Candida rugosa

Vinyl decanoate-modified dextran macromolecules (DexT40-VD) were synthesized in dimethyl sulfoxide at 50°C using lipase AY from Candida rugosa for catalyzing transesterification between polysaccharide and vinyl fatty esters. The extent of dextran modification (quantified by the molar ratio of attached alkyl tails to sugar repeat units) with native-, pH-adjusted-, 18-crown-6 ether pretreated pH-adjusted-, and stepwise addition of pretreated lipase AY yielded <3%, 49%, 64% and 96% modified dextran respectively. Lipase AY accelerated the transesterification of DexT40 from 2- to 63-fold higher than the non-catalyzed system. This procedure was extended to other acyl donors showing that modification pattern exhibited regioselectivity depending on acyl donor structure. Regioselectivity equaled between 2- and 3-OH with saturated fatty acyl donors. The 2-OH was favored for unsaturated fatty acyl donors, while sterically hindered acyl donors oriented modification toward 3-OH position. DexT40-VD at 96% modification was a water-insoluble polymer forming 150nm diameter nanoparticles in water which can be used as drug carrier systems.     

Quiescent crystallization of natural fibers–polypropylene composites

The effect of natural fibers (vetiver grass and rossells) on quiescent crystallization of polypropylene (PP) composites was analyzed in this study. Also, equilibrium melting temperature (T) of the composites was elucidated. Natural fiber‐PP composites showed lower T when compared to neat PP. Thermal analysis was performed via differential scanning calorimeter to study the crystallization kinetics. Natural fiber‐PP composites exhibited higher rate of crystallization than that of neat PP. Furthermore, spherulitic growth rate and transcrystallinity of the composites were investigated under a polarized light optical microscope. It was found that the growth rates of the composites were lower than that of neat PP. The spherulitic growth rates combined with the crystallization rates were used to calculate number of effective nuclei. It was shown that the number of effective nuclei of the composites was higher than that of neat PP. This suggested that natural fibers could act as a nucleating agent in the composite. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Mechanical and aging resistance performance of acrylic sheets containing EPDM-graft-poly(styrene-co-methyl methacrylate)

The addition of ethylene-propylene-diene rubber (EPDM) into acrylic sheets was expected to enhance their thermal and UV aging resistance for outdoor applications. According to the dissimilar polarity of EPDM and styrene (ST)/methyl methacrylate (MMA) monomer mixture (20/80% (w/w)) used for preparation of acrylic sheets, this research aimed to modify EPDM via graft copolymerization with ST and MMA to increase its compatibility. The graft copolymerization of ST and MMA at a ST/MMA ratio of 25/75% (w/w) onto EPDM was carried out in the solution polymerization initiated by benzoyl peroxide at 90 °C for 16 h, resulting in 88.1% grafting efficiency. The addition of 1.0–3.0% (w/w) of graft EPDM (GEPDM) into the acrylic sheets increased their impact strength (~ 17–22%), but decreased their flexural strength (~ 12–36%). However, their mechanical properties were improved after thermal and UV aging. Scanning electron microscopy (SEM) based analysis of the modified acrylic sheets revealed that the fracture surface shifted from brittle to ductile failure characteristics after modification. The thermogravimetric analysis results also exhibited that the addition of GEPDM improved the thermal and UV resistance of the modified acrylic sheets by increasing their initial decomposition temperature and activation energy of thermal decomposition.     

Glycidyl methacrylate grafted natural rubber: Synthesis,characterization, and mechanical property

Glycidyl methacrylate (GMA) was grafted onto natural rubber (NR) using emulsion polymerization method. The structures of copolymers were characterized by ¹H nuclear magnetic resonance (¹H‐NMR), solid state ¹³C‐NMR spectroscopy, and Fourier transform infrared spectrometer (FTIR). The %grafting obtained from the gravimetric method and the absorbance ratio were compared. Effects of reaction temperature, GMA content, and reaction time on %grafting, grafting efficiency, and %conversion of GMA monomer were determined. Effect of %grafting on mechanical properties of the graft copolymer was studied. Experimental result showed that the appropriate reaction time was 8 h at a reaction temperature of 30°C. Moreover, tensile strength and modulus of the graft copolymer increased with increasing %grafting. However, elongation at break of the graft copolymer decreased with increasing %grafting. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci 122: 3152–3159, 2011     

Compatibility enhancement of silica and natural rubber compound using UVA-induced silane-grafted saponified skim natural rubber

Silane coupling agents are potential reagents widely used to improve the compatibility between silica and less polar rubber, especially natural rubber (NR). Nevertheless, high temperature is generally required to generate the interaction between the components during the mixing process. Accordingly, an alternative method by grafting the silane coupling agent onto the rubber molecules would be a desirable approach to develop a compatibilizer for the silica-filled NR compound. In this work, skim NR was used as a starting material due to its linear structure. The optimal conditions of the grafting reaction were found to be 1 phr of an alkoxy silane and 5 phr of benzoyl peroxide under 8 min of UVA irradiation time. These conditions were applied for producing the rubber material used in the mixing process of STR 5L and silica. The cure characteristics, silica dispersion and mechanical properties of the rubber compounds were improved, suggesting that the modified rubber was an efficient material for increasing the compatibility between silica and NR.     

Controlled degradation of natural rubber and modification of the obtained telechelic oligoisoprenes: Preliminary study of their potentiality as polyurethane foam precursors

Telechelic oligoisoprenes were successfully prepared by the selective controlled degradation of natural rubber, a renewable source, via epoxidation and cleavage reactions. The molar mass of the oligoisoprene product obtained depends on the degree of epoxidation of the starting materials. The chemically modified structures obtained via epoxidation, hydrogenation, and ring opening of epoxide groups were also studied, and the chemical structures and thermal properties of the oligoisoprene products were determined. Moreover, the preliminary study of preparation of hydroxytelechelic natural rubber (HTNR)‐based polyurethane foam was performed. A novel HTNR‐based polyurethane foam was successfully prepared and its thermal properties were investigated and the results indicated that the HTNR‐based polyurethane foam has a good low temperature flexibility. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and physico‐mechanical,thermal and acoustic properties of flexible polyurethane foams based on hydroxytelechelic natural rubber

Novel flexible polyurethane foams were successfully prepared from a renewable source, hydroxytelechelic natural rubber (HTNR) having different molecular weights (1000–3400 g mol^?1) and variation of epoxide contents (EHTNR, 0–35% epoxidation) by a one‐shot technique. The chemical and cell structures as well as physico‐mechanical, thermal, and acoustic properties were characterized and compared with commercial polyol analogs. The obtained HTNR based foams are open cell structures with cell dimensions between 0.38 and 0.47 mm. The HTNR1000 based foam exhibits better mechanical properties but lower elongation at break than those of commercial polyol analog. However, the HTNR3400 based foam shows the best elastic properties. In a series of EHTNR based foams, the tensile and compressive strengths show a tendency to increase with increasing epoxide content and amount of 1,4‐butanediol (BD). The HTNR based foams demonstrate better low temperature flexibility than that of the foam based on commercial polyol. Moreover, the HTNR based polyurethane foams was found to be an excellent absorber of acoustics. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Plasma-treated polyethylene film: A smart material applied for Salmonella Typhimurium detection

Salmonella is a major cause of foodborne illness worldwide and is not allowed to be present in any food in all countries. The purpose of this study is to develop a simple alternative method for the detection of Salmonella based on functionalized polyethylene (PE) surfaces. Salmonella Typhimurium was used as a model bacterium. PE film was treated using dielectric plasma in order to alter the wettability of the PE surface and consequently introduce functionality on the surface. The PE film characterized by ATR-FTIR spectroscopy revealed the presence of CO stretching of ketones, aldehydes and carboxylic acids. The antibodies against O or H antigens of Salmonella and S. Typhimurium were then respectively immobilized on the PE surface after activation of the carboxylic group using NHS/EDC followed by protein A. The evidences from ATR-FTIR, scanning electron microscopy and optical microscopy showed the presence of S. Typhimurium attached to the plasma treated PE surfaces via the two types of anti-Salmonella antibody. The plasma treated PE film developed is simple and allows efficient association of bacterial cells on the treated surfaces without the necessity of time-consuming centrifugation and washing steps for isolation of the cells. This material is considered to be a smart material applicable for S. Typhimurium detection.     

Effect of poly(styrene-co-maleic anhydride) compatibilizer on properties of polystyrene/zinc oxide composites

The effects of polystyrene-co-maleic anhydride (SMA) compatibilizer on mechanical, thermal and morphological properties of polystyrene (PS)/zinc oxide (ZnO) composites were investigated for the first time in this study. PS/ZnO composites were prepared using a twin screw extruder and were then molded by compression method. In order to improve adhesion between filler and matrix, SMA compatibilizer is used in the composites. Tensile strength and Young??s modulus were increased with increasing ZnO and SMA at low concentration, but they were decreased with increasing high concentrations of ZnO and SMA content. Thus, mechanical properties can be enhanced in the composites with SMA compatibilizer. Moreover due to the effect of particle size, 250?nm ZnO particles (ZnO250) improved the mechanical properties of PS more than 71?nm ZnO particles (ZnO71) due to the increased aggregation of latter particles. Glass transition temperatures were not significantly changed when both ZnO and SMA were incorporated. Degradation temperatures of the composites increased with the addition of ZnO particles compared with neat PS and slightly decreased with the incorporation of SMA compared with the nascent composite. Scanning electron microscopy (SEM) analysis showed the better dispersion and compatibility of ZnO particles in PS/ZnO composites with the addition of SMA especially at the content of 3?wt%.