Fabrication of layered polydimethylsiloxane/perfluoropolyether microfluidic devices with solvent compatibility and valve functionality

The development of multilayer soft lithography methodology has seen polydimethysiloxane (PDMS) as the preferred material for the fabrication of microfluidic devices. However, the functionality of these PDMS microfluidic chips is often limited by the poor chemical resistance of PDMS to certain solvents. Here, we propose the use of a photocurable perfluoropolyether (PFPE), specifically FOMBLIN^® MD40 PFPE, as a candidate material to provide a solvent-resistant buffer layer to make the device substantially impervious to chemically induced swelling. We first carried out a systematic study of the solvent resistance properties of FOMBLIN^® MD40 PFPE as compared with PDMS. The comparison presented here demonstrates the superiority of FOMBLIN^® MD40 PFPE over PDMS in this regard; moreover, the results permitted to categorize solvents in four different groups depending on their swelling ratio. We then present a step-by-step recipe for a novel fabrication process that uses multilayer lithography to construct a comprehensive solvent-resistant device with fluid and control channels integrated with a valve structure and also permitting easy establishment of outside connections.     

Ergonomic evaluation of hospital bed design features during patient handling tasks

Patient handling tasks (e.g., transportation and repositioning) are important causes of musculoskeletal disorders among healthcare workers. The purpose of this study was to evaluate, during two patient handling tasks, the physical demands resulting from alternative hospital bed design features. Twenty-four novice participants were involved in two laboratory-based studies. The effects of a steering lock and adjustable push height were evaluated during a patient transportation task using perceptual responses and measures of performance and physical demands, and the effect of a bed contour feature was determined based on patient sliding distance during repeated bed raising/lowering. Use of the steering lock reduced the number of adjustments during bed maneuvering by 28% and decreased ratings of physical demands. Use of the adjustable push height reduced shoulder moments by 30%. With the contour feature, patient sliding distance was reduced by ∼40% over 12 raise/lower cycles. These results suggest that the steering lock and adjustable push height features can reduce physical demands placed on healthcare workers during patient transportation tasks. Although patient sliding distance was reduced using the contour feature, assessing direct effects of this feature on physical demands (e.g., reduced need for workers to reposition patients) will require further investigation.

Relevance to industry

Hospital bed design features have the potential to reduce physical demands required of healthcare workers, yet there have been only limited empirical studies of these. Findings of the two current studies suggest that proactive ergonomic considerations in hospital bed design can reduce these physical demands.     

Detecting localized homogeneous anomalies over spatio-temporal data

The last decade has witnessed an unprecedented growth in availability of data having spatio-temporal characteristics. Given the scale and richness of such data, finding spatio-temporal patterns that demonstrate significantly different behavior from their neighbors could be of interest for various application scenarios such as—weather modeling, analyzing spread of disease outbreaks, monitoring traffic congestions, and so on. In this paper, we propose an automated approach of exploring and discovering such anomalous patterns irrespective of the underlying domain from which the data is recovered. Our approach differs significantly from traditional methods of spatial outlier detection, and employs two phases—(i) discovering homogeneous regions, and (ii) evaluating these regions as anomalies based on their statistical difference from a generalized neighborhood. We evaluate the quality of our approach and distinguish it from existing techniques via an extensive experimental evaluation.     

A Novel Highly Sensitive Humidity Sensor Based on ZnO/SBA‐15 Hybrid Nanocomposite

This work deals with the study of hydrothermally synthesized zinc oxide (ZnO) loaded mesoporous SBA‐15 hybrid nanocomposite for relative humidity sensing (RH) at room temperature. The sensor exhibits an excellent ~5 orders impedance change along with excellent linearity, quick response time (17 s), rapid recovery time (18 s), negligible hysteresis (1.2%), good repeatability, and stability (1.8%) in 11%–98% RH range. In addition, complex impedance spectra of the sensor at different RHs were analyzed to understand the humidity sensing mechanism. Our study can open a new way for realizing ZnO/SBA‐15 hybrid nanocomposite for fabrication of high‐performance RH sensors.     

Nanocomposites based on transition metal oxides in polyvinyl alcohol for EMI shielding application

In the present work, the nanocomposites based on different transition metal oxides like iron oxide (Fe₂O₃), zinc oxide (ZnO), silicon dioxide (SiO₂), zirconium dioxide (ZrO₂), and titanium dioxide (TiO₂) in PVA matrix have been studied for their suitability as electromagnetic interference (EMI) shielding materials in the frequency range of 4–8 GHz (C-band) and 8–12 GHz (X-band). The nanocomposites containing 0.1, 0.5, 1.0, 5.0, and 10.0 wt% of oxides in the matrix were synthesised by solvent casting method. The EMI attenuation studies in 4–12 GHz frequency range were carried out using the Vector Network Analyzer R & S: ZVA40 method by measuring the loss due to reflection. The minimum reflectivity values for the composites containing Fe₂O₃, ZnO, SiO_2, ZrO₂, and TiO₂ in PVA matrix at 10 wt% concentration level in the matrix were found to be ?38.85 dB (10.4 GHz), ?33.65 dB (10.4 GHz), ?41.90 dB (10.4 GHz), ?24.90 dB (11.0 GHz), and ?32.90 dB (9.76 GHz), respectively. Based on these results, the SiO₂- and Fe₂O₃-based composites, which also exhibit high thermal stability and mechanical strength, are found to be low-cost and efficient EMI shielding materials.     

Intensification of Freeze-Drying Rate of Bacillus subtilis MTCC 2396 Using Tungsten Halogen Radiation: Optimization of Moisture Content and α-Amylase Activity

A novel freeze-drying protocol has been explored to render fast and cost-effective freeze drying of hyperamylase producing Bacillus subtilis MTCC2396 employing a tungsten halogen lamp radiator (THLR) as a heat source. Response surface methodology assessed the maximum reduction in moisture content (96.07%) and minimum reduction in α-amylase (EC 3.2.1.1) activity (1.02%) in 4 h drying time at 42.5°C radiation temperature. α-amylase activity (0.046 U) and final moisture content (3.93%) of the optimally freeze-dried bacterial strain appeared satisfactory. The freeze-drying time using THLR (4 h) is remarkably lower compared to that under a conventional conductive plate heater (CPH) (10 h) at otherwise identical conditions. The higher effective moisture diffusivity of 0.0052 to 0.0078 m ²/s under THLR compared to 0.00084 to 0.0015 m ²/s under CPH (corresponding to 20–50°C) advocated the superiority of the THLR heating protocol. The higher efficacy of THLR was also evidenced through lower activation energy (8.42 kJ/mol) of moisture diffusion compared to that (12.051 kJ/mol) of CPH. The optimally freeze-dried bacteria demonstrated the same growth rate in addition to exhibiting excellent retention of bioremedial (Hg²⁺ removal) activity to that of the control.     

Synthesis, properties and biomedical applications of poly(glycerol sebacate) (PGS): A review

Poly(glycerol sebacate) (PGS) is a biodegradable polymer increasingly used in a variety of biomedical applications. This polyester is prepared by polycondensation of glycerol and sebacic acid. PGS exhibits biocompatibility and biodegradability, both highly relevant properties in biomedical applications. PGS also involves cost effective production with the possibility of up scaling to industrial production. In addition, the mechanical properties and degradation kinetics of PGS can be tailored to match the requirements of intended applications by controlling curing time, curing temperature, reactants concentration and the degree of acrylation in acrylated PGS. Because of the flexible and elastomeric nature of PGS, its biomedical applications have mainly targeted soft tissue replacement and the engineering of soft tissues, such as cardiac muscle, blood, nerve, cartilage and retina. However, applications of PGS are being expanded to include drug delivery, tissue adhesive and hard tissue (i.e., bone) regeneration. The design and fabrication of PGS based devices for applications that mimic native physiological conditions are also being pursued. Novel designs range from accordion-like honeycomb structures for cardiac patches, gecko-like surfaces for tissue adhesives to PGS (nano) fibers for extra cellular matrix (ECM) like constructs; new design avenues are being investigated to meet the ever growing demand for replacement tissues and organs. In less than a decade PGS has become a material of great scrutiny and interest by the biomedical research community. In this review we consolidate the valuable existing knowledge in the fields of synthesis, properties and biomedical applications of PGS and PGS-related biomaterials and devices.     

Role of hydrogen in electrical and structural characteristics of bilayer CdTe/Mn diluted magnetic semiconductor thin films

Bilayer thin films of diluted magnetic semiconductor CdTe/Mn have been prepared using vacuum thermal evaporation method at pressure of 10⁻⁵ torr. Annealing of bilayer thin films has been performed in atmospheric condition at constant temperature 400 °C for 1 hour. Hydrogenation of as-grown and annealed bilayer thin films has been performed by keeping these in hydrogenation cell. Structural characteristics of as-grown and heat treated thin films have been performed by X-ray diffractometer. Current–voltage characteristics of both as-grown hydrogenated and annealed hydrogenated bilayer thin films have been studied to find out the effect of hydrogenation. Surface topography of as-grown and annealed bilayer thin films has been confirmed by optical microscopy.     

Effect of hydrogen on interface of metal–semiconductor Schottky diode

The effect of hydrogen on p-type Si/Mn and Si/Co Schottky diode has been investigated in present studies. The variations of I–V characteristics suggested that the rectifying act of these diodes change with variation of hydrogen pressure, which is due to the diffusion of hydrogen through the Mn and Co metal films up to Si surface or a creation of surface states at the interface. It is also observed that the effect of hydrogen found to be reverse in order for forward as well as reverse direction of current in Mn and Co deposited films on Si substrate, corresponding to anionic and protonic model of hydrogen interaction with metals. One can say that hydrogen plays an amphoteric role to neutralize either donors or acceptors level in semiconductors and metals. The Raman spectra of Si/Mn and Si/Co are taken and stoke lines link with the presence of hydrogen is observed. In this paper, we are presenting the role of hydrogen pressure on I–V characteristics at the interface of metal–semiconductor structure.