Electron-microscopic procedure for acrylic rubber

The electron-microscopic visualization of acrylic rubber dispersed in a heterogeneous structural resin composition consisting of a rubber-modified two-phase plastic comprising essentially a butyl acrylate rubber phase and an acrylonitrile–styrene copolymer phase, respectively, has been accomplished. This procedure consists of the following: The molded resin specimen is treated with hydrazine hydrate solution to produce the acrylic acid hydrazides. Allow the treated specimen to soak in osmium tetroxide solution. The acrylic rubber may be indirectly fixed and stained. Some micrographs of ultrathin sections of two or three resin compositions, cut by an ultramicrotome, are presented.     

Synthesis of poly(tetrahydrofuran-b-ε-caprolactone) macromonomer via the Sml2-induced transformation

Summary A novel well-defined macromonomer consisting of different types of monomers in polymerization mechanisms was synthesized for the first time through the SmI₂-induced transformation. The macromonomer, -methacryloylpoly-(tetrahydrofuran-b--caprolactone), was prepared by the reaction of methacryloyl chloride with living poly(tetrahydrofuran-b--caprolactone) [poly(THF-b-CL)] which was obtained by the two-electron reduction of the cationic growing center of poly(THF) by samarium iodide (SmI₂) followed by the polymerization of CL. ¹H NMR analysis indicated the quantitative introduction of the methacryloyl group onto the polymer end. The molecular weight distribution of the macromonomer was relatively narrow, and the unit ratio of THF to CL could be controlled by both polymerization time of THF and the amount of CL, resulting from the living nature of both CL- and THF-polymerizations. Radical copolymerization of the produced macromonomers with methyl methacrylate in the presence of AIBN resulted in a polymethacrylate backbone grafted with poly(THF-b-CL) block copolymers.     

Immunological Pathomechanisms of Spongiotic Dermatitis in Skin Lesions of Atopic Dermatitis

Atopic dermatitis (AD) is a chronic pruritic skin disease with a complex pathogenesis underlying its heterogeneous clinical phenotypes and endotypes. The skin manifestation of AD reflects the cytokine milieu of a type-2-dominant immunity axis induced by genetic predisposition, innate immunity dysregulation, epidermal barrier defects, and allergic inflammation. However, the detailed pathomechanism of eczematous dermatitis, which is the principal characteristic of AD, remains unclear. This review examines previous studies demonstrating research progress in this area and considers the immunological pathomechanism of “spongiotic dermatitis”, which is the histopathological hallmark of eczematous dermatitis. Studies in this field have revealed the importance of IgE-mediated delayed-type hypersensitivity, the Fas/Fas-ligand system, and cell-mediated cytotoxicity in inducing the apoptosis of keratinocytes in spongiotic dermatitis. Recent studies have demonstrated that, together with infiltrating CD4 T cells, IgE-expressing dendritic cells (i.e., inflammatory dendritic epidermal cells and Langerhans cells) that capture specific allergens (i.e., house dust mites) are present in the spongiotic epidermis of lichenified eczema in patients with IgE-allergic AD. These findings suggest that IgE-mediated delayed-type hypersensitivity plays a pivotal role in the pathogenesis of spongiotic dermatitis in the skin lesions of AD.     

Characterization of electrode/electrolyte interface for lithium batteries using in situ synchrotron X-ray reflectometry—A new experimental technique for LiCoO2 model electrode

A new experimental technique was developed for detecting structure changes at electrode/electrolyte interface of lithium cell using X-ray reflectometry and two-dimensional model electrodes with a restricted lattice-plane. The electrodes were constructed with an epitaxial film of LiCoO₂ synthesized by pulsed laser deposition method. The orientation of the epitaxial film depends on the substrate plane; the 2D layer of LiCoO₂ is parallel to the SrTiO₃ (1 1 1) substrate (_(0 0 3)LiCoO₂//_(1 1 1)SrTiO₃)$({(003)}_{\text{LiCo}{\text{O}}_2}//{(111)}_{\text{SrTi}{\text{O}}_3})$, while the 2D layer is perpendicular to the SrTiO₃ (1 1 0) substrate (_(1 1 0)LiCoO₂//_(1 1 0)SrTiO₃)$({(110)}_{\text{LiCo}{\text{O}}_2}//{(110)}_{\text{SrTi}{\text{O}}_3})$. The anisotropic properties were confirmed by electrochemical measurements. Ex situ X-ray reflectivity measurements indicated that the impurity layer existed on the as-grown LiCoO₂ was dissolved and a new SEI layer with lower density was formed after soaking into the electrolyte. In situ X-ray reflectivity measurements indicated that the surface roughness of the intercalation (1 1 0) plane increased with applying voltages, while no significant changes in surface morphology were observed for the intercalation non-active (0 0 3) plane during the pristine stage of the charge–discharge process.     

All solid-state battery with sulfur electrode and thio-LISICON electrolyte

A high-capacity type of all solid-state battery was developed using sulfur electrode and the thio-LISICON electrolyte. New nano-composite of sulfur and acetylene black (AB) with an average particle size of 1–10 nm was fabricated by gas-phase mixing and showed a reversible capacity of 900 mAh g⁻¹ at a current density of 0.013 mA cm⁻².     

Radiation-induced polymerization of ethylene in a pilot plant. I. Bulk process

Radiation-induced bulk polymerization of ethylene was carried out with use of a pilot plant with a 10 liter reactor at pressures of 225–400 kg/cm², temperatures of 30–95°C, ethylene feed rates of 5–28 kg/hr, and dose rate of 3.8 × 10⁵ rad/hr. Characteristics of the process are mild polymerization conditions and capability of producing medium density polyethylene in powder form. The spacetime yield and molecular weight of polymer were in the range of 3.5 to 13.1 g/liter hr and 2.2 × 10⁴ to 14 × 10⁴, respectively. The space-time yield increased with mean residence time and 2.4 powders of pressure, and decreased with temperature. Molecular weight changed similarly with the reaction conditions. These results were consistent with those of the bench plant experiment and the scale effect was small. Polymer deposit to the reactor wall limited a period of continuous operation of the plant. The amount of deposited polymer was increased with the square of reaction time. The rate of polymer deposit was proportional to polymer concentration and to the cube of pressure. The polymer deposit cannot be solved in the bulk process.     

Molecular characterization of antibiotic-resistant salmonella isolates from retail meat from markets in northern Vietnam

A total of 118 Salmonella isolates were detected from 283 retail meat samples (135 pork and 148 chicken meat) purchased at retail markets in Northern Vietnam. Thirteen serovars, including Infantis, Anatum, Rissen, Reading, Emek, Typhimurium, Blockley, London, Newport, Derby, Weltevreden, Albany, and Hadar, were determined. Resistance to tetracycline (54.2%), sulfonamides (52.5%), streptomycin (41.5%), trimethoprim (36.4%), chloramphenicol (35.6%), and ampicillin (33.1%) was commonly seen in the Salmonella isolates. Fourteen [bla(TEM), bla(OXA-1), bla(PSE-1), aadA1, sul1, tetA, tetB, tetG, cmlA1, floR, dfrA1, dfrA12, aac(3)-IV, and aphA1-1AB ] of 17 resistance genes were detected from the isolates demonstrating resistance. Genes for plasmid-mediated quinolone resistance, such as qnrA, qnrB, qnrS, qepA, and acc(6')-1b-cr, were not detected in 23 quinoloneresistant isolates. The substitution TCC to TTC at codon 83 of gyrA was found in the 18 quinolone-resistant isolates. The data revealed that resistant Salmonella strains were widely distributed in Northern Vietnam via the food chain and that they might contain multiple genes specifying identical resistance phenotypes. Thus, further studies are necessary to clarify the mechanisms of antibiotic resistance in Salmonella strains and their spread in the livestock market.     

Photocatalytic partial oxidation of methylpyridine isomers on TiO2 particles under an anaerobic condition

Photocatalytic oxidation of methylpyridine isomers (2-methylpyridine, 3-methylpyridine, and 4-methylpyridine) was investigated in a mixed solution of acetonitrile and water or acetonitrile using various kinds of TiO₂ powders as photocatalysts. The main products from methylpyridine isomers were pyridinecarboxaldehyde isomers (2-pyridinecarboxaldehyde, 3-pyridinecarboxaldehyde, and 4-pyridinecarboxaldehyde). Rutile large TiO₂ particles showed the highest level of activity for oxidation of 2-methylpyridine probably because band bending was necessary for the oxidation of 2-methylpyridine. On the other hand, a fine particle having an anatase or rutile phase showed a higher level of activity than large TiO₂ particles for oxidation of 3-methylpyridine. A rutile fine particle showed the highest level of activity for the reaction. It was found that pure rutile or pure anatase particles were inactive for oxidation of 4-mathylpyridine. If the particles are not extremely small, pure rutile and pure anatase powders show fairly high levels of activity, and those containing both anatase and rutile phases show the highest level of activity. The activity of pure rutile particles was also enhanced by physically mixing them with a small amount of small anatase particles, which were inactive for this reaction. These results can be explained by the synergism between rutile and anatase particles. All of these reactions effectively proceeded even under anaerobic conditions. Photocatalytic reduction of methylpyridine isomers concomitantly proceeded on TiO₂ particles under the conditions used. These results suggest that the activities of TiO₂ photocatalysts for oxidation of methylpyridine isomers are dominated by the oxidation potential of alkylpiridine and band bending of TiO₂ particles.     

Photocatalytic Activity of a TiO<Subscript>2</Subscript> Photocatalyst Doped with C<Superscript>4+</Superscript> and S<Superscript>4+</Superscript> Ions Having a Rutile Phase Under Visible Light

C⁴⁺ and S⁴⁺-codoped titanium dioxide (TiO₂) having a rutile phase was prepared. By doping C⁴⁺ and S⁴⁺ ions into a TiO₂ lattice, the absorption edge of rutile TiO₂ powder was largely shifted from 400 to 700 nm. 2-Methylpyridine and methyleneblue were photocatalytically oxidized at high efficiency on C⁴⁺ and S⁴⁺-doped TiO₂ under visible light at a wavelength longer than 5 nm.     

Isolation of Solid Solution Phases in Size‐Controlled LixFePO4 at Room Temperature

State‐of‐the‐art LiFePO₄ technology has now opened the door for lithium ion batteries to take their place in large‐scale applications such as plug‐in hybrid vehicles. A high level of safety, significant cost reduction, and huge power generation are on the verge of being guaranteed for the most advanced energy storage system. The room‐temperature phase diagram is essential to understand the facile electrode reaction of Li_xFePO₄ (0 < x < 1), but it has not been fully understood. Here, intermediate solid solution phases close to x = 0 and x = 1 have been isolated at room temperature. Size‐dependent modification of the phase diagram, as well as the systematic variation of lattice parameters inside the solid‐solution compositional domain closely related to the electrochemical redox potential, are demonstrated. These experimental results reveal that the excess capacity that has been observed above and below the two‐phase equilibrium potential is largely due to the bulk solid solution, and thus support the size‐dependent miscibility gap model.