Practical method for generation expansion planning based on dynamic programming

This paper presents an efficient method which provides the optimal generation mix and the optimal generation construction process. The approximation method in which the dynamic programming technique and gradient method are combined is applied to determine the optimal generation mix with hydropower generation technologies. The successive approximations dynamic programming (SADP) technique, which is very suitable for high-dimensional multistage decision process problems, is used for obtaining the optimal generation construction process. The effectiveness and feasibility of the developed technique are demonstrated on a practical power system model which has five types of generation technologies including a hydropower generation technology.     

Heparin affinity high-performance liquid chromatography as an alternative to bioassay of CS23 mutein of recombinant human basic fibroblast growth factor

We investigated whether a chemical assay by high-performance liquid chromatography (HPLC) as an alternative to the complicated and time-consuming bioassay for CS23 mutein of recombinant human basic fibroblast growth factor (rhbFGF-CS23) using the fetal bovine heart endothelial cell line ATCC CRL 1395. Physically, chemically or enzymatically denatured rhbFGF-CS23 was subjected to heparin affinity (HA)-HPLC and the bioassay. Good agreement was observed between the results obtained by these two methods. Moreover, HA-HPLC gave much more reproducible results (RSD = 1.9%, n = 6) than the bioassay (RSD = 7.4%, n = 18). HA-HPLC is therefore a simple, accurate and reproducible alternative to the bioassay for quality control and stability studies for rhbFGF-CS23 preparations. HA-HPLC is also considered to be applicable to assays for FGFs which have heparin affinity and biological activity similar to those of the CS23 mutein.     

Effects of nondensifying inclusions on the densification and microstructure of zinc oxide matrix composites

The densification and microstructure development of ZnO containing Zn₇Sb₂O₁₂, ZrO₂, and aggregated ZnO were investigated to elucidate the effect of nondensifying inclusions on the sintering of ceramic/ceramic composites. The inclusion retarded the densification, and the degree of retardation was found to depend on the chemical species of inclusion; Zn₇Sb₂O₁₂ had the largest effect, followed by ZrO₂ and then aggregated ZnO last. The experimental results for aggregated ZnO was explained by the theory which predicts the generation of backstresses. The backstresses give a less significant effect on the densification. For Zn₇Sb₂O₁₂ and ZrO₂, the microstructure of the matrix varied with distance from an inclusion particle; much porosity was observed in the region surrounding the inclusion. Circumferential voids, which are responsible for the suppression of densification, form during the initial stage of sintering. Inclusion particles generate an anchoring effect which retards the densification of the matrix immediately surrounding the inclusion particle during the intermediate stage.Supported by the Inamori Foundation.     

Strength and ductility under dynamic loading in fine- grained IN905XL aluminum alloy

Three IN905XL aluminum alloys with fine grain (1 μm), intermediate grain (3 μm), and coarse grain (5 μm) have been developed by a combination of mechanical alloying (MA) and conventional extrusion in order to investigate their mechanical properties at dynamic strain rates of 1 × 10³ and 2 × 10³ s⁻¹ and a quasi-static strain rate of 10^-3 s⁻¹. Flow stresses are found to increase with decreasing grain size for all the strain rates tested. Negative strain-rate sensitivity of flow stress is observed up to 1 × 10³ s⁻¹ in both intermediate- and coarse-grained IN905XL. At the highest strain rate of 2 × 10³ s⁻¹ however, all samples showed a positive strain-rate sensitivity of strength. Total elongation at high strain rates is generally larger than that at low strain rates. Total elongation also decreases with grain size for all the strain rates. This decrease in elongation results from an initiation of microcracks at interfaces between the matrix and particles finely dispersed near grain boundary regions, introduced during MA processing; then, this initiation leads elongation of alloys to small limited values. Formerly with the Department of Mechanical Systems Engineering, University of Osaka Prefecture. This article is based on a presentation made in the symposium “Dynamic Behavior of Materials,” presented at the 1994 Fall Meeting of TMS/ASM in Rosemont, Illinois, October 3-5, 1994, under the auspices of the TMS-SMD Mechanical Metallurgy Committee and the ASM-MSD Flow and Fracture Committee.     

Gel chromism and anomalous luminescence in poly(3-alkylthiophene)

The absorption spectrum of poly(3-alkylthiophene) gel changes drastically in association with a volume instability upon changing the solvent composition and also the temperature. In the expanded state in chloroform and at high temperature, the photoluminescence is much enhanced compared with the shrunken state in ethanol and at low temperature. This gel chromism and anomalous luminescence are discussed in terms of the change of effective conjugation length induced by the steric hindrance and the dynamics of the photoexcited species.     

The origination and optimization of Si/SiO/sub 2/ interface roughness and its effect on CMOS performance

As CMOS device dimensions scale down to 100 nm and beyond, the interface roughness between Si and SiO/sub 2/ has become critical to device performance and reliability. Si/SiO/sub 2/ interface roughness degrades channel mobility decreasing drive currents. The authors have used atomic force microscopy to study surface roughness in the processing of 0.16 /spl mu/m CMOS integrated circuits. All of the process steps that could potentially affect the interface roughness have been studied. The results show that oxidation is the major contributor to the interface roughness. The rms roughness is found to be linearly dependent on oxide thickness. Transistors with Si/SiO/sub 2/ interface rms roughness that has been reduced from 1.6 to 1.1 /spl Aring/ by reducing oxide thicknesses show improved device drive currents. This technique for interfacial smoothing and device performance improvement has the advantage of being easily implemented in today's technology.     

Interconnected power systems with superconducting magnetic energy storage

The objective of this work is to discuss the concept of back‐to‐back interconnection systems with energy storage, especially with a Superconducting Magnetic Energy Storage (SMES) incorporated into a back‐to‐back DC link. In this case, each converter of the back‐to‐back system is used as a power conditioning system for the SMES coils. Since the AC–DC converter can be designed independently of the frequency of the power system, a two‐way switch is connected to the AC side of each converter. This two‐way switch can select the interconnected power systems. By using the two‐way switches, this system can provide the stored energy in the SMES system to each interconnected power system through two AC–DC converters. For instance, lower‐cost power of each power network can be stored through two converters during the off‐peak hours and made available for dispatch to each power network during periods of demand peak. Then this system increases the reliability of electric power networks and enables the economical operations depending on the power demand. This paper describes the unique operations of the back‐to‐back interconnection with SMES and discuses the optimal SMES configuration for a 300‐MW‐class back‐to‐back interconnection. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(2): 37–43, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20482     

Quantitative trait loci affecting 4-nitroquinoline 1-oxide-induced tongue carcinogenesis in the rat

The incidence of tongue carcinomas (TCs) induced by oral administration of 4-nitroquinoline 1-oxide in rats is strain dependent. The inbred Dark-Agouti (DA) strain showed a much higher susceptibility to large mass-forming infiltrative TCs than did the Wistar-Furth (WF) strain. Our previous study (M. Kitano et al, Jpn. J. Cancer Res., 87: 1097-1101, 1996) on crosses between these two strains postulated a dominant susceptibility gene in DA and a dominant resistance gene in WF rats. The present study mapped these loci by analyzing the backcrosses to each parent with simple sequence repeat polymorphisms. Five quantitative parameters were analyzed: (a) the number of TCs > 5 mm in diameter; (b) the total number of TCs per rat; (c) the diameter of the largest TCs (DTCmax values); (d) the number of non-TC cancers per rat; and (e) and the number of cancers of any site per rat. All of these parameters were closely correlated (P < 0.0001). DA rats had a semidominant gene (Stc1) favoring the development of 4-nitroquinoline 1-oxide-induced cancers on chromosome 19, closely linked to D19Mit9. Peak linkage was observed 4 cM distal from D19Mit9, with a logarithm of the odds (lod) score of 5.72 for the number of large TCs and 6.08 for the DTCmax. On the other hand, WF rats had a semidominant gene (Rtc1) mapped between D1Mit1 and D1Mit3, approximately 20 cM from D1Mit1, with a peak lod score of 3.30 for both the number of large TCs and the DTCmax. The main effect of Rtc1 seemed to be to reduce the size of the TCs. The action of these genes was dose dependent and cooperative. The final incidence of TC in DA, WF, F1, and backcross rats seemed to be explained by combinations of genotype at these two loci. Possible candidate genes for Stc1 and Rtc1 are discussed.     

Development of a Cyclogyro-Based Flying Robot With Variable Attack Angle Mechanisms

This paper presents an experimental study on the development of a cyclogyro-based flying robot with a new variable angle of attack mechanism. A cyclogyro is a flying machine supported in the air by power-driven rotors that rotate about a horizontal axis, like the paddle-wheels of a steamboat. Machines of this type have been designed by some companies but there has been no record of any successful flights. Our design starts with a new variable angle of attack mechanism with an eccentric (rotational) point in addition to a rotational point connecting to a motor. The main feature of the mechanism with the eccentric rotational point is the ability to change attack of angles in accordance with the wing positions (as determined by the rotational angles of the cyclogyro) without actuators. The design parameters (wing span, the number of wings, and eccentric distance) of the flying robot are determined through a series of experiments. Experimental results show that the cyclogyro-based flying robot with the new variable angle of attack mechanism is capable of generating sufficient lift force for flying.