Practical method for generation expansion planning based on dynamic programming

This paper presents an efficient method which provides the optimal generation mix and the optimal generation construction process. The approximation method in which the dynamic programming technique and gradient method are combined is applied to determine the optimal generation mix with hydropower generation technologies. The successive approximations dynamic programming (SADP) technique, which is very suitable for high-dimensional multistage decision process problems, is used for obtaining the optimal generation construction process. The effectiveness and feasibility of the developed technique are demonstrated on a practical power system model which has five types of generation technologies including a hydropower generation technology.     

Effects of nondensifying inclusions on the densification and microstructure of zinc oxide matrix composites

The densification and microstructure development of ZnO containing Zn₇Sb₂O₁₂, ZrO₂, and aggregated ZnO were investigated to elucidate the effect of nondensifying inclusions on the sintering of ceramic/ceramic composites. The inclusion retarded the densification, and the degree of retardation was found to depend on the chemical species of inclusion; Zn₇Sb₂O₁₂ had the largest effect, followed by ZrO₂ and then aggregated ZnO last. The experimental results for aggregated ZnO was explained by the theory which predicts the generation of backstresses. The backstresses give a less significant effect on the densification. For Zn₇Sb₂O₁₂ and ZrO₂, the microstructure of the matrix varied with distance from an inclusion particle; much porosity was observed in the region surrounding the inclusion. Circumferential voids, which are responsible for the suppression of densification, form during the initial stage of sintering. Inclusion particles generate an anchoring effect which retards the densification of the matrix immediately surrounding the inclusion particle during the intermediate stage.Supported by the Inamori Foundation.     

A 10-s doping technology for the application of low-temperaturepolysilicon TFTs to giant microelectronics

A bucket-type high-density (0.25-1.2-mA/cm²) low-energy (500-2000 V) ion source was utilized for high-speed phosphorus doping directly into a thin polysilicon layer without cap SiO₂. Doping gas with He dilution was selected to reduce etching of polysilicon film. Excimer laser (XeCl, 8 mm×8 mm) pulse annealing was introduced to activate effectively the doped impurity. The combination of these techniques provided a practically low sheet resistance for the TFT source, drain, and gate with a short time doping. The low-temperature polysilicon TFT fabricated with a doping time of 10 s had characteristics comparable to those of that fabricated by a longer time doping or conventional ion implantation, showing the practicality of this technology and its promise for giant microelectronics     

Gel chromism and anomalous luminescence in poly(3-alkylthiophene)

The absorption spectrum of poly(3-alkylthiophene) gel changes drastically in association with a volume instability upon changing the solvent composition and also the temperature. In the expanded state in chloroform and at high temperature, the photoluminescence is much enhanced compared with the shrunken state in ethanol and at low temperature. This gel chromism and anomalous luminescence are discussed in terms of the change of effective conjugation length induced by the steric hindrance and the dynamics of the photoexcited species.     

Changes in Aging Behavior and Defect Structure of Yttria-Fully-Stabilized ZrO2 with Sc2O3 Doping

Methods of suppressing decreased conductivity in 8 mol% Y₂O₃-stabilized–92 mol% ZrO₂ (8YSZ) with aging were investigated. Different amounts of Sc₂O₃ were doped into 8YSZ. The electrochemical properties of Sc₂O₃-doped 8YSZ were measured, and the microstructural and local structural changes were characterized. The present results indicate that an appropriate amount of Sc₂O₃ doping, 3 or 4 mol%, effectively suppresses decreased conductivity with aging in 8YSZ.     

Interconnected power systems with superconducting magnetic energy storage

The objective of this work is to discuss the concept of back‐to‐back interconnection systems with energy storage, especially with a Superconducting Magnetic Energy Storage (SMES) incorporated into a back‐to‐back DC link. In this case, each converter of the back‐to‐back system is used as a power conditioning system for the SMES coils. Since the AC–DC converter can be designed independently of the frequency of the power system, a two‐way switch is connected to the AC side of each converter. This two‐way switch can select the interconnected power systems. By using the two‐way switches, this system can provide the stored energy in the SMES system to each interconnected power system through two AC–DC converters. For instance, lower‐cost power of each power network can be stored through two converters during the off‐peak hours and made available for dispatch to each power network during periods of demand peak. Then this system increases the reliability of electric power networks and enables the economical operations depending on the power demand. This paper describes the unique operations of the back‐to‐back interconnection with SMES and discuses the optimal SMES configuration for a 300‐MW‐class back‐to‐back interconnection. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(2): 37–43, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20482     

Interface potential of calcium phosphate in simulated body fluid

Calcium phosphate ceramics are used in the substitution of injured or damaged bones. Nevertheless, the behaviour of these materials, and in particular, the mechanisms guiding their interface response in physiological environment is still unknown. This work describes the construction of hydroxyapatite and tricalcium phosphate electrodes used to determine the interface potential behaviour of these materials in a simulated body fluid, in a pH range corresponding to the variation observed in human body injuries, at ambient and physiological temperatures. These measurements are associated with the adsorption/desorption of ions from the materials. The results show that hydroxyapatite and tricalcium phosphate have similar behaviour in that they reach an interface potential equilibrium state faster when the solution pH is decreased and the temperature increased. This behaviour may be attributed to their ability to form a calcium-rich layer and is relevant to their quality as implantable materials.     

Mapping evapotranspiration using MODIS and MM5 Four-Dimensional Data Assimilation

Evapotranspiration (ET), the sum of evaporation from soil and transpiration from vegetation, is of vital importance in the hydrologic cycle and must be taken into consideration in assessments of the water resources of any region. The MODerate resolution Imaging Spectroradiometer (MODIS) sensor offers a promising opportunity for estimating daily ET with a 1 km spatial resolution, but is hampered by frequent cloud contamination or data gaps from other factors. In this study, 1) a stand-alone ET model was applied and tested during clear or partial cloudy sky conditions using MODIS-based inputs of land surface and atmospheric data and 2) meteorological simulations by using Four-Dimensional Data Assimilation (FDDA) system between MODIS and the 5th Generation Meso-scale Meteorological Model (MM5) was used in cloudy conditions to facilitate continuous daily ET estimates. The MODIS ET algorithm modified from Mu et al. (2007) is based on the Penman-Monteith equation and was applied to predict ET at flux measurement sites. This algorithm considers both the effects of surface energy partitioning processes and environmental constraints on ET. We devised gap-filling approaches for MODIS aerosol and albedo data that were identified as bottlenecks to determine retrieval rates of insolation and ET. MODIS-derived input variables (i.e., meteorological variables and radiation components) for estimating ET showed a good agreement with flux tower observations at each site. The retrieval rate of MODIS ET doubled at four flux measurement sites after gap-filling with negligible compensation was undertaken for accuracy. In spite of the high accuracy of MODIS-derived input variables, MODIS ET showed meaningful errors at the four flux measurement sites. These errors were mainly associated with errors in the estimated canopy conductance. During clear sky conditions, MODIS was used to calculate ET, while the MODIS-MM5 FDDA system provided input variables for the calculation of ET under cloudy sky conditions. The performance of the MODIS-MM5 FDDA system was evaluated by comparing ET based on MODIS, which showed a good agreement with the MODIS ET for various land cover types. Our results indicate that MODIS can be applied to monitor the land surface energy budget and ET with reasonable accuracy and that MODIS-MM5 FDDA has the potential to provide reasonable input data of ET estimation under cloudy conditions.     

Hydrothermal preparation of tailored hydroxyapatite

Hydrothermal vapor treatment method was applied for preparation of ceramic biomaterials. Hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂; HA) ceramics prepared by sintering with random crystal surface have already been used as bone-repairing materials which can directly bond to natural bones. If materials of HA could have the tailored specific crystal surface, they should have the advantage of adsorptive activity and osteoconductivity in comparison with the sintered HA. In the present study, porous HA sheets of about 50 μm to 1 mm in thickness and porous HA granules of about 50 μm to 1 mm in size with tailored crystal surface were prepared by the hydrothermal vapor exposure method at temperatures below 200°C. Porous sheets and porous granules of HA with controlled crystal surface should be suitable for scaffold of cultured bone, for bone graft material and for drug delivery system (DDS).     

Demonstration of a fully spatial coherent X-ray laser at 13.9 nm

We have recently reported the successful development of a fully coherent X-ray laser (XRL) at 13.9 nm by an oscillator-amplifier configuration with two targets. In the experiment, a seed XRL beam from the first target is injected into a plasma amplifier at the second target. The observed XRL beam has full spatial coherence and 0.2 mrad of nearly diffraction-limited divergence. In order to improve the output fluence, the amplification properties of the XRL beam have been investigated using various plasma lengths of the second amplifier target. The output energy has been improved by a factor of ten, increasing the length of the gain region to 10 mm, resulting in about 0.2 /spl mu/J of output energy.