Spectral shape tunable band-rejection filter using a long-period fiber grating with divided coil heaters

We have developed a new type of tunable band rejection filter, which provides high spectral-shaping flexibility in a wide tuning range. The filter consists of a long-period fiber grating (LPFG) with divided coil heaters. Each of the divided coil heaters is controlled individually to adjust a temperature distribution along the LPFG and to modify the spectral shape of the LPFG filter. The tunable band rejection filter is demonstrated to function properly when applied as an erbium-doped fiber amplifier gain-flattening filter.     

Solid phase crystallization of amorphous silicon on glass by thin film heater for thin film transistor (TFT) application

A new process for solid phase crystallization (SPC) of amorphous silicon (a-Si) using thin film heater is reported. With this localized Ti silicide thin film heater, we successfully crystallized 500 Å-thick a-Si in a few minutes without any thermal deformation of glass substrate. The size of crystallized silicon grain was abnormally big (30-40 μm). Polycrystalline thin film transistors (TFT) fabricated using this unique thin film heater showed better mobility than those of conventional ones by furnace annealing.     

Area- and time-specific marginal capacity costs of electricity distribution

Marginal costs of electricity vary by time and location. In the past, researchers attributed the variations to factors related to electricity generation and transmission. These authors, however, have not analyzed possible variations in marginal distribution capacity costs (MDCC). The objectives of this paper are:

1. (i) to show that large MDCC variations are due to the dispersion in distribution capital expenditures by time and space,

2. (ii) to propose a method for quantifying the area- and time-specific MDCC in the presence of lumpy investments, and

3. (iii) to compare our MDCC estimates to those commonly used in the electric utility industry.

Our proposed method and its results were adopted by the California Public Utilities Commission (CPUC) in 1992 for Pacific Gas and Electric Company (PG&E), the largest privately owned electric utility in the U.S.     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry     

Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

A Nonvolatile Organic Memory Device Using ITO Surfaces Modified by Ag‐Nanodots

We report on a single‐layer organic memory device made of poly(N‐vinylcarbazole) embedded between an Al electrode and ITO modified with Ag nanodots (Ag‐NDs). Devices exhibit high ON/OFF switching ratios of 10⁴. This level of performance could be achieved by modifying the ITO electrodes with some Ag‐NDs that act as trapping sites, reducing the current in the OFF state. Temperature dependence of the electrical characteristics suggest that the current of the low‐resistance state can be attributed to Schottky charge tunnelling through low‐resistance pathways of Al particles in the polymer layer and that the high‐resistance state can be controlled by charge trapping by the Al particles and Ag‐NDs.     

Synthesis of Mg-α-sialon from the mixture of silicon, aluminum and magnesia powders in a flowing nitrogen atmosphere

Synthesis of Mg-α-Sialon has been investigated by the mixture of silicon, aluminum and magnesia powders in a flowing nitrogen atmosphere in the range of 1300–1600 °C, when Mg-α-Sialon is designed with a chemical formulation of Mg _x Si_12−3x Al_3x O _x N_16−x in present work. The results showed that Mg-α-sialon initially occurred at 1400 °C and basically increased with elevated temperatures. For the samples of x = 0.6, 0.8 and 1.0 the products mainly consisted of Mg-α-Sialon with small amounts of Si, AlN and 21R AlN-polytypoid phases at 1600° C. However, in final products of x = 1.2, 1.4 and 1.6 only a little of Mg-α-Sialon formed and a great amount of Si remained in these samples at all the fired temperatures. Fortunately, the content of Mg-α-Sialon in these samples were obviously increased by adding a small amount of α-Si₃N₄ as seeds before nitridation.     

Phacoemulsification with a bevel-down phaco tip: phaco-drill

We present a technique for in situ lens nucleus emulsification using low phaco power and high vacuum, a continuous curvilinear capsulorhexis, and hydrodelineation. Emulsification is done with the phaco tip slanted down 30 or 45 degrees. Cutting and aspiration do not cause an undesirable energy loss. This technique can be combined with the nuclear chopping or divide and conquer methods because of its ability to drill and hold the nucleus. Posterior capsular rupture is prevented because the separated epinucleus acts as a barrier between the nucleus and the cortex. The low power used minimizes the energy transfer to the corneal endothelium. This technique is particularly useful in eyes with brunescent cataract.     

Enhanced direct stiffness method for finite element analysis of textile composites

Traditional homogenization techniques are not useful when the microstructural scale of a material is of the same order of magnitude as the structural scale of a component. Such is the case for many textile composites. Since discrete modeling of the microstructure throughout a component is prohibitively expensive, continuum finite elements are needed which account for the microstructure within a single element. This paper describes a simple substructuring technique for formulating these special elements.     

Serum amyloid P component scintigraphy and turnover studies for diagnosis and quantitative monitoring of AA amyloidosis in juvenile rheumatoid arthritis

OBJECTIVE: To evaluate aspects of the natural history of AA amyloidosis complicating juvenile rheumatoid arthritis (JRA), and its response to therapy with chlorambucil. METHODS: Scintigraphy and 7-day turnover studies were performed in JRA patients with histologically proven (n = 35) or clinically suspected (n = 30) AA amyloidosis, following intravenous injection of 123I and 125I-labeled serum amyloid P component (SAP). Prospective monitoring studies were performed over 2-3 years in 20 patients with amyloidosis. All but 2 amyloidosis patients were treated with chlorambucil. RESULTS: Positive scanning results were obtained in all patients in whom imaging was performed within 12 years of positive biopsy findings of amyloid and in 5 patients with clinically suspected amyloidosis. Negative scanning results with normal SAP metabolism, indicating regression of amyloid, were obtained in 4 patients whose amyloidosis had been in full clinical remission for more than 12 years. Prospective monitoring studies in patients whose JRA-associated inflammatory activity was in remission demonstrated regression of amyloid in 8 patients and no substantial changes in 8 others; however, in 4 further patients with active inflammation, there was accumulation of amyloid. There was a very poor correlation between the amount of amyloid present at a particular site and the resultant organ dysfunction. CONCLUSION: Radiolabeled SAP scintigraphy and turnover studies are useful complementary tools in the diagnosis, screening, and quantitative monitoring of type AA amyloidosis in JRA. The amyloid deposits may progress and/or regress at different rates in different anatomic sites over short periods.