Synthesis and characterization of new thermally stable poly(ester‐imide)s derived from 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl and various aromatic dihydroxy compounds

A series of new alternating aromatic poly(ester‐imide)s were prepared by the polycondensation of the preformed imide ring‐containing diacids, 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl (2a) and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl (2b) with various aromatic dihydroxy compounds in the presence of pyridine and lithium chloride. A model compound (3) was also prepared by the reaction of 2b with phenol, its synthesis permitting an optimization of polymerization conditions. Poly(ester‐imides) were fully characterized by FTIR, UV‐vis and NMR spectroscopy. Both biphenylene‐ and binaphthylene‐based poly(ester‐imide)s exhibited excellent solubility in common organic solvents such as tetrahydrofuran, m‐cresol, pyridine and dichloromethane. However, binaphthylene‐based poly(ester‐imide)s were more soluble than those of biphenylene‐based polymers in highly polar organic solvents, including N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide and dimethyl sulfoxide. From differential scanning calorimetry thermograms, the polymers showed glass‐transition temperatures between 261 and 315 °C. Thermal behaviour of the polymers obtained was characterized by thermogravimetric analysis, and the 10 % weight loss temperatures of the poly(ester‐imide)s was in the range 449–491 °C in nitrogen. Furthermore, crystallinity of the polymers was estimated by means of wide‐angle X‐ray diffraction. The resultant poly(ester‐imide)s exhibited nearly an amorphous nature, except poly(ester‐imide)s derived from hydroquinone and 4,4′‐dihydroxybiphenyl. In general, polymers containing binaphthyl units showed higher thermal stability but lower crystallinity than polymers containing biphenyl units. Copyright © 2005 Society of Chemical Industry     

Lossless,Passive Transportation of Low Surface Tension Liquids Induced by Patterned Omniphobic Liquidlike Polymer Brushes

Surfaces enabling directional liquid transportation are of great interest for a wide range of applications such as water collection, microfluidics, and heat transfer systems. Surfaces capable of lossless, long-range passive transportation of low surface tension (LST) liquids using wettability patterned, liquidlike coatings with minimal contact angle hysteresis are reported. Lossless LST droplet travel distances over 150 mm are achieved, enabled by a two-phase transportation mechanism: morphological transformation from a bulge to a channel shape, followed by directional transportation along the asymmetrical wedge-shaped channel. The developed surfaces can split, merge, and precisely transport various low-surface tension liquids, including alcohols, alkanes, and solvents. The developed transportation strategy can also enhance LST liquid dropwise condensation through continuous removal of the condensate, even on horizontally positioned surfaces without the assistance of gravity.     

A hybrid multi-criteria decision-making model for firms competence evaluation

In this paper, we present a hybrid multi-criteria decision-making (MCDM) model to evaluate the competence of the firms. According to the competence-based theory reveals that firm competencies are recognized from exclusive and unique capabilities that each firm enjoy in marketplace and are tightly intertwined within different business functions throughout the company. Therefore, competence in the firm is a composite of various attributes. Among them many intangible and tangible attributes are difficult to measure. In order to overcome the issue, we invite fuzzy set theory into the measurement of performance. In this paper first we calculate the weight of each criterion through adaptive analytic hierarchy process (AHP) approach (A³) method, and then we appraise the performance of firms via linguistic variables which are expressed as trapezoidal fuzzy numbers. In the next step we transform these fuzzy numbers into interval data by means of α-cut. Then considering different values for α we rank the firms through TOPSIS method with interval data. Since there are different ranks for different α values, we apply linear assignment method to obtain final rank for alternatives.     

A soft robotics nonlinear hybrid position/force control for tendon driven catheters

Minimally invasive steerable catheters, commonly implemented in cardiac ablation, are currently operated by interventionalists exposing them to X-ray radiation and requiring the dexterity for accurate steering. To conduct robot-assisted cardiac ablation, highly accurate stable control platform for precise force/position control on the moving tissue is required. This paper introduces hybrid force/position control strategy to apply a constant force to the cardiac tissue while tracking the desired trajectory. The position controller is based on a nonlinear model predictive tracking control satisfying the input constraints. Cosserat rod theory is incorporated for the distal shaft modeling of tendon-driven catheters, and the model is reformulated for controller design and stability proof. Lyapunov-based stability analysis is conducted. To apply the controller, the force-displacement mapping of the cardiac tissue is obtained through ex vivo experimental tests. The performance of the controller is evaluated, and the catheter is capable of regulating the force with the RMSE of 4.9 mN and tracking the position with the RMSE of 0.89 mm. The promising results verify the potential of the application of the introduced approach in real applications including in vitro and clinical cardiac ablation.     

Modeling industrial thickener using computational fluid dynamics (CFD), a case study: Tailing thickener in the Sarcheshmeh copper mine

Separation of particles from liquid in the large gravitational tanks is widely used in mining and industrial wastewater treatment process. Thickener is key unit in the operational processes of hydrometallurgy and is used to separate solid from liquid. In this study, population balance models were combined with computational fluid dynamics (CFD) for modeling the tailing thickener. Parameters such as feed flow rate, flocculant dosage, inlet solid percent and feedwell were investigated. CFD was used to simulate the industrial tailing thickener with settled bed of 120 m diameter which is located in the Sarcheshmeh copper mine. Important factor of drag force that defines the rake torque of rotating paddles on the bed was also determined. Two phases turbulence model of Eulerian/Eulerian in accordance with turbulence model of k-ε was used in the steady-state. Also population balance model consists of 15 groups of particle sizes with Luo and Lehr kernel was used for aggregation/breakage kernel. The simulation results showed good agreement with the operational data.     

Error from Delay Drift in Terahertz Attenuated Total Reflection Spectroscopy

In this article we discuss the influence of temporal stability on the value obtained for dielectric properties of materials measured by terahertz time-domain spectroscopy with particular emphasis on attenuated total reflection. The stability of three different terahertz attenuated total reflection spectroscopy systems is carefully characterized. The formalism for the complex refractive index extraction is presented and the effect of delay errors is calculated numerically. We found that good thermal stability of the terahertz system helps to minimize delay fluctuations and therefore the uncertainty of the resulting complex refractive index.     

Simple preparation and characterization of molecularly imprinted nylon 6 nanofibers for the extraction of bisphenol A from wastewater

Nylon 6 nanofibers incorporated with molecularly imprinted polymers (MIPs) were successfully fabricated by electrospinning with fiber diameters in the range 80–145 nm. Then, they were used as a new material for the extraction of selected bisphenol A (BPA) in water samples. Field emission scanning electron microscopy images revealed that the nanofibers had a smooth morphology with a good incorporation of MIPs. The Fourier transform infrared and energy-dispersive X-ray spectroscopy results also confirmed the formation of the MIPs in the nanofibers. Furthermore, Raman spectroscopy showed that the crystalline structure of the pristine nylon 6 nanofiber was a kind of α form, and the incorporation of MIPs led to a γ-form structure in the nanofibers; this proved the interactions between nylon 6 and the MIPs. Adsorption studies also confirmed that the adsorption efficiency of BPA onto the molecularly imprinted polymer nanofibers (MIP-NFs; 83.5%) was much greater than that onto nonimprinted polymer nanofibers (NIP-NFs; 36.8%). Also, the imprinting factor was 3.4; this strongly implied the successful formation of molecularly imprinted cavities on the MIP-NFs with a strong affinity to BPA. The maximum adsorption capacity of the MIP-NFs was 103.8 mg/g. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47112.     

The Effect of Ti on Mechanical Properties of Extruded In-Situ Al-15 pct Mg2Si Composite

This work was carried out to investigate the effect of different Ti concentrations as a modifying agent on the microstructure and tensile properties of an in-situ Al-15 pctMg₂Si composite. Cast, modified, and homogenized small ingots were extruded at 753 K (480 °C) at the extrusion ratio of 18:1 and ram speed of 1 mm/s. Various techniques including metallography, tensile testing, and scanning electron microscopy were used to characterize the mechanical behavior, microstructural observations, and fracture mechanisms of this composite. The results showed that 0.5 pctTi addition and homogenizing treatment were highly effective in modifying Mg₂Si particles. The results also exhibited that the addition of Ti up to 0.5 pct increases both ultimate tensile strength (UTS) and tensile elongation values. The highest UTS and elongation values were found to be 245 MPa and 9.5 pct for homogenized and extruded Al-15 pctMg₂Si-0.5 pctTi composite, respectively. Fracture surface examinations revealed a transition from brittle fracture mode in the as-cast composite to ductile fracture in homogenized and extruded specimens. This can be attributed to the changes in size and morphology of Mg₂Si intermetallic and porosity content.     

The release rate and antimicrobial activity of calcium-alginate films containing self-microemulsifying Thymus vulgaris essential oil against Escherichia coli and Staphylococcus aureus

The aim of this study was to fabricate antimicrobial calcium-alginate-based films containing the self-microemulsifying thyme essential oil (TEO) formulations using Tween 80 as the surfactant, and acetic (AA) or propionic (PA) acids as the cosurfactants. A Ca-alginate film containing nano-emulsified TEO as well as a neat Ca-alginate film were considered as the controls. The scanning electron microscopy micrographs showed a highly porous texture for SME films, which resulted in an increase in water vapor permeability and water absorption capacity of these films. The SME films released the TEO completely within 155 min and inhibited the growth of S. aureus and E. coli in in vitro antimicrobial tests. The population of S. aureus and E. coli reduced significantly in ground beef covered with SME films. The results of this study showed that self-microemulsifying TEO films could effectively increase the shelf life of ground beef by controlling its microbial population.     

Selective molecularly imprinted polymer nanofiber sorbent for the extraction of bisphenol A in a water sample

Novel molecularly imprinted polymer nanofibers (MIP‐NFs) were prepared for the adsorption of bisphenol A (BPA) in a water sample using the sol–gel process and the electrospinning technique. The effects of a number of synthesis parameters on the adsorption efficiency were investigated. The successful removal of BPA from MIP‐NFs was studied using UV–visible spectroscopy. The prepared MIP‐NFs were characterized by Fourier transform infrared, field emission SEM, TEM and energy dispersive X‐ray analysis. The results showed that the required molar ratio of 3‐aminopropyltriethoxysilane (APTES) to BPA was 15:1, which indicates a good performance in the rebinding test. Likewise, the molar ratio of APTES:acid:water was 1:2:9. The nylon 6 polymer solution, with a concentration of 12 wt%, showed a maximum adsorption capacity for BPA due to a decrease in the nanofiber diameter and an increase in the accessible sites. Furthermore, the maximum adsorption capacity of BPA was achieved at pH 7. Concerning the binding of BPA on MIP‐NFs, the experimental data matched well with the pseudo‐second‐order kinetics data and the Sips isotherm model. The saturated binding capacity for MIP‐NFs was predicted to be 115.1 mg g^?1, which was more than twice as high as that for non‐imprinted polymer nanofibers (46.82 mg g^?1). The results obtained in this study confirmed that the prepared MIP‐NFs showed considerable binding specificity for BPA in comparison with similar structural compounds such as phenol, naphthol and Naphthol AS, in aqueous solution. The binding capacity of MIP‐NFs remained almost constant after five cycles of reuse. The real sample analysis indicated that MIP‐NFs could be utilized as a useful sorbent material for the extraction of BPA from a water sample.