640-Gb/s high-speed ATM switching system based on 0.25-μm CMOS,MCM-C, and optical WDM interconnection

A 640-Gb/s high-speed ATM switching system that is based on the technologies of advanced MCM-C, 0.25-μm CMOS, and optical wavelength-division-multiplexing (WDM) interconnection is fabricated for future broadband backbone networks. A 40-layer, 160×114 mm ceramic MCM forms the basic ATM switch module with 80-Gb/s throughput. It consists of 8 advanced 0.25-μm CMOS LSIs and 32 I/O bipolar LSIs. The MCM has a 7-layer high-speed signal line structure having 50-Ω strip lines, high-speed signal lines, and 33 power supply layers formed using 50-μm thick ceramic layers to achieve high capacity. A uniquely structured closed-loop-type liquid cooling system for the MCM is used to cope with its high power dissipation of 230 W. A three-stage ATM switch is made using the optical WDM interconnection between high-performance MCMs. For WDM interconnection, newly developed compact 10-Gb/s, 8-WDM optical transmitter and receiver modules are used. These modules are each only 80×120×20 mm and dissipate 9.65 W and 22.5 W, respectively. They have a special chassis for cooling, which contains high-performance heat-conductive plates and micro-fans. An optical WDM router based on an arrayed waveguide router is used for mesh interconnection of boards. The optical WDM interconnect has 640-Gb/s throughput and simple interconnection     

Dye-sensitized solar cell based on nanocrystalline TiO<Subscript>2</Subscript> with 3–10 nm in diameter

Nanocrystalline TiO₂ with 3–10 nm in diameter was prepared with a surfactant-template method. Dye-sensitized solar cells were assembled using the prepared nanocrystalline TiO₂ with large surface area and high crystallinity, which achieved significant higher Jsc when compared to cells fabricated with bigger particles of 25 nm in diameter. In the cells with nanocrystalline TiO₂, the sintering temperature drastically affected the conversion performance of the cells.     

An integrated modeling approach to predict flooding on urban basin.

Correct prediction of flood extents in urban catchments has become a challenging issue. The traditional urban drainage models that consider only the sewerage-network are able to simulate the drainage system correctly until there is no overflow from the network inlet or manhole. When such overflows exist due to insufficient drainage capacity of downstream pipes or channels, it becomes difficult to reproduce the actual flood extents using these traditional one-phase simulation techniques. On the other hand, the traditional 2D models that simulate the surface flooding resulting from rainfall and/or levee break do not consider the sewerage network. As a result, the correct flooding situation is rarely addressed from those available traditional 1D and 2D models. This paper presents an integrated model that simultaneously simulates the sewerage network, river network and 2D mesh network to get correct flood extents. The model has been successfully applied into the Tenpaku basin (Nagoya, Japan), which experienced severe flooding with a maximum flood depth more than 1.5 m on September 11, 2000 when heavy rainfall, 580 mm in 28 hrs (return period > 100 yr), occurred over the catchments. Close agreements between the simulated flood depths and observed data ensure that the present integrated modeling approach is able to reproduce the urban flooding situation accurately, which rarely can be obtained through the traditional 1D and 2D modeling approaches.     

Solid-solution hardening and softening in binary iron alloys

Six dilute (0.2, 0.5 and 1 at %) binary iron-base alloys with Co, Cr, Al, Si, Mn and Ni were prepared after scavenging inherent carbon with Ti. From tensile and stress relaxation tests in the temperature range of 77 to 450 K, stress-strain behaviours and thermal activation parameters were analysed as functions of solute content and temperature. In the four alloys containing Ni, Mn, Al and Si, solid-solution softening occurs below 250 K while solid-solution hardening occurs above 250 K. In the alloys containing Co or Cr, neither softening nor hardening due to solute additions occurs at any temperature. Detailed analysis of thermal activation parameters leads one to conclude that the solid-solution softening in the above mentioned four alloys is due to a decrease in kink energy with increasing solute content, while in the latter two alloys no change in kink energy occurs. On the other hand, there exists a strong solute concentration dependence of the athermal component, suggesting that the solid-solution hardening is due to the interaction of dislocations with groups of substitutional solute atoms that create lattice and modulus misfits.     

Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.     

Longitudinal elastic waves in columns due to earthquake motion

An analysis is presented of longitudinal waves in a thin elastic column. Velocity is specified at one end, and the boundary condition at the other end is expressed in terms of a range of effective impedances of an attached structure. Propagation, reflection and interference of the waves are followed by the method of characteristics. Integration of differential equations along characteristics yields the wave-induced stress, which is then applied to problems of earthquake excitation. Numerical examples are given for recorded updown ground motion of the Kobe Earthquake.     

Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

Polyanion induced preferential multinucleation in macrophages at a low level of TNF-alpha secretion

When rat bone marrow macrophages were incubated with acetyl lignin (EP3) in the presence of a 10% solution of fetal bovine serum, the macrophages secreted tumor necrosis factor (TNF-alpha) in a dose-dependent manner. This was followed by macrophage multinucleation. EP3 was found to have a significant effect on TNF-alpha secretion at a minimum dose of 5 micrograms/ml and produced no significant further increase at levels above 50 micrograms/ml, while multinucleation was most active at 10 micrograms/ml. However, multinucleation did not occur at higher concentrations of EP3 (50 micrograms/ml and 100 micrograms/ml). Secretion of TNF-alpha was significantly reduced in the absence of fetal bovine serum, whereas multinucleation was very active, starting after 6 h of incubation. At concentrations of 100 micrograms/ml, sulfonyl lignin (LS) and dextran sulfate (DS) only induced low levels of TNF-alpha secretion from macrophages, but induced active multinucleation. The multinucleation induced by addition of LS or DS was inhibited by further addition of EP3. Thus, macrophage multinucleation was most active when a low level of TNF-alpha was secreted from the macrophages.