Dye-sensitized solar cell based on nanocrystalline TiO<Subscript>2</Subscript> with 3–10 nm in diameter

Nanocrystalline TiO₂ with 3–10 nm in diameter was prepared with a surfactant-template method. Dye-sensitized solar cells were assembled using the prepared nanocrystalline TiO₂ with large surface area and high crystallinity, which achieved significant higher Jsc when compared to cells fabricated with bigger particles of 25 nm in diameter. In the cells with nanocrystalline TiO₂, the sintering temperature drastically affected the conversion performance of the cells.     

The relationship of IL-6 to hormonal mediators, fuel utilization, and systemic hypermetabolism after surgical trauma

OBJECTIVES: To define the relationship between inflammatory cytokines, hormonal mediators, alteration of energy substrate and hypermetabolism during the early phase after surgical trauma. DESIGN: A prospective case-control study of 13 patients underwent elective surgery for carcinoma between November 1993 and January 1995. MATERIALS AND METHODS: They received parenteral supply of adequate glucose and amino acids through central venous catheter after surgery equally. Inflammatory cytokines such as TNF- alpha, IL-1 and IL-6, stress hormones such as norepinephrine, glucagon and insulin, and fuel utilization and hypermetabolism variables such as resting energy expenditure (REE), CRP, free fatty acid, respiratory quotient, the calculated rates of glucose and fat oxidation using indirect calorimetry were measured serially (the day before operation, the end of surgery, and postoperative day (POD) 1, 2 and 5). MEASUREMENTS AND MAIN RESULTS: TNF- alpha and IL-1 were not detected during the study period. Initial elevation and steady decline of IL-6 concentrations were seen after surgical injury, and this response related significantly to post-operative norepinephrine and glucagon levels throughout the study period, and to insulin levels only at the end of surgery. %REE (REE/BEEHB; basal energy expenditure according to the Harris-Benedict equation) on POD 2 and 5, and all CRP levels after surgery were significantly related to IL-6 levels more than hormone levels. Fuel utilization variables on POD 2 were related to both IL-6 and hormone levels. CONCLUSIONS: Initial elevation of IL-6 concentration might induce stress hormones such as norepinephrine and glucagon, but not insulin after surgical trauma. Moreover not only hormonal mediators but also cytokine such as IL-6 are responsible for the development of the stress response of the alteration of energy substrate and hypermetabolism.     

An integrated modeling approach to predict flooding on urban basin.

Correct prediction of flood extents in urban catchments has become a challenging issue. The traditional urban drainage models that consider only the sewerage-network are able to simulate the drainage system correctly until there is no overflow from the network inlet or manhole. When such overflows exist due to insufficient drainage capacity of downstream pipes or channels, it becomes difficult to reproduce the actual flood extents using these traditional one-phase simulation techniques. On the other hand, the traditional 2D models that simulate the surface flooding resulting from rainfall and/or levee break do not consider the sewerage network. As a result, the correct flooding situation is rarely addressed from those available traditional 1D and 2D models. This paper presents an integrated model that simultaneously simulates the sewerage network, river network and 2D mesh network to get correct flood extents. The model has been successfully applied into the Tenpaku basin (Nagoya, Japan), which experienced severe flooding with a maximum flood depth more than 1.5 m on September 11, 2000 when heavy rainfall, 580 mm in 28 hrs (return period > 100 yr), occurred over the catchments. Close agreements between the simulated flood depths and observed data ensure that the present integrated modeling approach is able to reproduce the urban flooding situation accurately, which rarely can be obtained through the traditional 1D and 2D modeling approaches.     

Automated low-power technique exploiting multiple supply voltagesapplied to a media processor

This paper describes an automated design technique to reduce power by making use of two supply voltages. The technique consists of structure synthesis, placement, and routing. The structure synthesizer clusters the gates off the critical paths so as to supply the reduced voltage to save power. The placement and routing tool assigns either the reduced voltage or the unreduced one to each row so as to minimize the area overhead. The reduced supply, voltage is also exploited in a clock tree to reduce power. Combining these techniques together, we applied it to a media processor chip. The combined technique reduced the power by 47% in random-logic modules and by 73% in the clock tree, while keeping the performance     

Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.     

Electrical properties of N2O/NH3 plasma grownoxynitride on strained-Si

Growth of ultrathin (<100 Å) oxynitride on strained-Si using microwave N₂O and NH₃ plasma is reported. X-ray photoelectron spectroscopy (XPS) results indicate a nitrogen-rich layer at the strained-Si/SiO₂ interface. The electrical properties of oxynitrides have been characterized using a metal-insulator-semiconductor (MIS) structure. A moderately low value of insulator charge density (6.1×10¹⁰ cm^-2) has been obtained for NH₃ plasma treated N₂O oxide sample. Nitrided oxide shows a larger breakdown voltage and an improved charge trapping properties under Fowler-Nordheim (F-N) constant current stress     

The cause of the uneven carbonization process in wet coal charging in coke oven chamber

In the case of the wet coal charging process in coke oven chamber, it is known that the coking process is uneven and a local carbonization delay occurs. The reason was investigated through a laboratory-scale experiment and a quantitative estimation. A partial carbonization test in a test coke oven replicated the uneven plastic layer and local carbonization delay. It was revealed that most of the gas generated in the uncarbonized coal layer results from the evaporation of condensed water and that steam can break through the plastic layer in a test coke oven. Moreover, the order estimation implied that steam that generates in the uncarbonized coal layer and breaks through the plastic layer has sufficient heat capacity to cool the heating wall and delay the carbonization. It was also shown that the steam pressure peak measured in a commercial coke oven is much lower than the estimated steam pressure in this study assuming steam not breaking through the plastic layer. The above-mentioned results and quantitative investigation strongly support the ‘steam breaking through the plastic layer’ theory proposed by Dr. Rohde that an uneven carbonization process is caused by vaporized coal moisture breaking through the plastic layer at definite, unforeseeable points, which results in cooling of the wall by the steam flow.     

Ideal crosslinked-polymers and their characterization in free-radical monovinyl-divinyl copolymerizations

The critical conditions in which the classical Flory-Stockmayer gelation theory (F-S theory) is applicable to monovinyl-divinyl copolymerizations were pursued in detail. The resulting prepolymers or precursors of ideal crosslinked-polymers were characterized as standard polymers for the discussion of network formation in free-radical monovinyl-divinyl copolymerizations. Methyl methacrylate was copolymerized with a small amount of ethylene dimethacrylate, butylene dimethacrylate or nonapropyleneglycol dimethacrylate in the presence of lauryl mercaptan, a chain transfer agent to reduce the occurrence of a thermodynamic excluded volume effect and intramolecular crosslinking as the primary and secondary factors, respectively, for the greatly delayed gelation in the free-radical monovinyl-divinyl copolymerizations and, moreover, to keep the primary chain length constant by inhibiting a gel effect. The ratio of the actual gel point to the theoretical one reached 1.1, supporting the validity of F-S theory. The resulting prepolymers were subjected to SEC-MALLS analysis to determine the molecular weights, the molecular-weight distributions and the radii of gyration; the correlations of molecular weight vs. elution volume and radius of gyration vs. molecular weight were useful for the characterization of the precursors of ideal network-polymers.