A practical Equivalent Electrical Circuit model for Proton Exchange Membrane Fuel Cell (PEMFC) systems

An alternative Equivalent Electrical Circuit for Proton Exchange Membrane Fuel Cells is modelled in this study. Both I–V characteristics and H₂ consumptions corresponding to generated power under load and no-load conditions are investigated. For this purpose, H₂ consumptions and I–V characteristics of three different sized PEMFCs are tested. There is a very good harmony between the model results and measured values (relative error %0.7, %6.4 and %2.5 for FC-A, FC-B and FC-C respectively). In the proposed model current passes only on parallel resistance and not on serial resistance at no-load condition. Thus, a FC with higher parallel resistance should be preferred. Another key output of this study is that based on the proposed model, performance comparison of FCs can be performed with the parameters defined in this work. Proposals made in this study can easily be used for performance analysis of FCs under for both steady state and transient analysis.     

Partitioning of predominant lipophilic bioactives (squalene, α-tocopherol and β-sitosterol) during olive oil processing

The partitioning of predominant lipophilic olive bioactives (squalene, β-sitosterol and α-tocopherol) in olive oil processing was studied for the first time using common integrated olive milling plant. 7% of the oil and 5% of the squalene present in the olives was lost in the last pomace. β-sitosterol and α-tocopherol, which are mainly concentrated in the seed of the olive fruit, was recovered in virgin olive oil to a lesser extent (66%, 67%) while 10% were lost in last pomace. Thus, the loss of β-sitosterol and α-tocopherol was higher than that of squalene and oil, due to nonrecovered bound forms. 19% of the α-tocopherol and 21% of the β-sitosterol loss was unaccounted for, which can be attributed to degradation of α-tocopherol and incomplete recovery of sterols from the olive and pomace matrices. This study provides a basis for process development studies.     

Optimal design of elastic beams with segmentwise constant height in the case of dynamic loading

A shape optimization method for elastic beams with segmentwise constant height is proposed. The ends of the beam are simply supported, clamped or free. Two problems are discussed; (i) a beam is loaded by lateral pressure, (ii) a beam is struck by an attached mass. External loads and volume of the beam are prescribed and the deflection in a given cross-section is to be minimized. For solving this problem, the deflections are expanded into a Fourier series by eigenfunctions. Numerical results are given for two-, three- and four-stepped beams.     

3D Hair sketching for real-time dynamic & key frame animations

Physically based simulation of human hair is a well studied and well known problem. But the “pure” physically based representation of hair (and other animation elements) is not the only concern of the animators, who want to “control” the creation and animation phases of the content. This paper describes a sketch-based tool, with which a user can both create hair models with different styling parameters and produce animations of these created hair models using physically and key frame-based techniques. The model creation and animation production tasks are all performed with direct manipulation techniques in real-time.     

A protein which masks galactose receptor mediated phage susceptibility in Lactococcus lactis subsp. lactis MPL56

A 28.5-kb plasmid, isolated from Lactococcus lactis subsp. lactis MPL56, causes complete inhibition of four lactococcal phages. Cell wall characteristics of wild-type strain MPL56 were compared with its 28.5 kb plasmid-cured, phage-sensitive derivative MPL56-22. After proteolytic enzyme treatments, adsorption of phages occurred at high levels, an example is 94.6–98.5% in MPL56 cells. Analysis of cell wall extracts of MPL56-22 by sodium dodecyl sulphate–polyacrylamide gel electrophoresis (SDS–PAGE) indicated that the only difference between strains was the 55.4 kDa band in protein patterns of MPL56. Adsorption of the four phages was completely inhibited when MPL56-22 cells were subjected to SDS, Triton-X-100, HCl and NaOH treatments. Lectins that were specific for glucose/mannose and N-acetylglucosamine did not prevent adsorption of phages in cell wall extracts of MPL 56-22. However a lectin specific for galactose (MCA; Momordica charantia ) completely inhibited adsorption of these phages in cell wall extracts of MPL56-22. HPLC patterns of cell wall carbohydrates of MPL56-22 and its HCl treated preparations showed that the most prevalent difference was the galactose on untreated MPL56-22 cell wall chromatograms.     

Relation between abrasion resistance and flexural strength of high volume fly ash concrete

In this paper, abrasion of high volume fly ash (HVFA) concretes made with 50% and 70% of cement replacement with fly ash was assessed in terms of its relation to flexural tensile strength. Comparisons were made between normal Portland cement (NPC) concrete and fly ash concrete. Comparisons were also made between fly ash concretes. Investigation results have shown that the abrasion resistance increased as flexural tensile strength increased. Analysis of the results showed that, for concrete with tensile strength of greater than 4–5 MPa, the abrasion resistance of HVFA concrete with 70% replacement with cement was found to be higher than that of counterpart control NPC concrete and concrete made with 50% fly ash. The comparison between the relation of abrasion to compressive strength and abrasion to flexural tensile strength made in terms of R² of the linear regression showed that a stronger relation existed between abrasion and flexural tensile strength than that of abrasion to compressive strength of the concrete studied.

---

Résumé L'étude a pour but d'estimer la relation entre la résistance à l'usure avec la résistance à la traction en flexion des bétons contenant de 50% et 70% de cendres volantes. On a comparé le béton pur au béton contenant des cendres volantes. Des comparaisons ont été faites également entre les différents bétons contenant des cendres volantes. Les resultats de la recherche ont montré que la résistance à l'usure augmente à mesure que la résistance à la traction en flexion de 4∼5 MPa ont une résistance à l'usure plus grande s'ils contienneint 70% de cendres volantes que s'ils étaient purs ou contenaient 50% de cendres volantes. La comparaison entre les relation de la résistance à l'usure en compression et de la résistance à l'usure en traction a été établie en termes de R² de la régression linéaire. On a prouvé qu'une relation plus forte a été obtenue entre la résistance à l'usure et la résistance à la traction en flexion par rapport à la résistance à l'usure en compression du béton étudié.