A novel context-aware recommender system based on a deep sequential learning approach (CReS)

Neural Computing and Applications - With an increase in online longitudinal users’ interactions, capturing users’ precise preferences and giving accurate recommendations have become an...     

运动饮料配方设计概论

运动中，人体生理发生一系列的变化，包括水分损失、血糖／糖原消耗、电解质损失等，导致运动中／后的疲劳和运动能力下降。以运动中人体生理特点为基础，通过讨论运动前／中／后补充水、碳水化合物及电解质的问题，论证了运动饮料配方设计的原理依据。     

Microstrip stepped impedance resonator bandpass filter with an extended optimal rejection bandwidth

Bandpass filters with an optimal rejection bandwidth are designed using parallel-coupled stepped impedance resonators (SIRs). The fundamental (f/sub o/) and higher order resonant harmonics of an SIR are analyzed against the length ratio of the high-Z and low-Z segments. It is found that an optimal length ratio can be obtained for each high-Z to low-Z impedance ratio to maximize the upper rejection bandwidth. A tapped-line input/output structure is exploited to create two extra transmission zeros in the stopband. The singly loaded Q(Q/sub si/) of a tapped SIR is derived. With the aid of Q/sub si/, the two zeros can be independently tuned over a wide frequency range. When the positions of the two zeros are purposely located at the two leading higher order harmonics, the upper rejection band can be greatly extended. Chebyshev bandpass filters with spurious resonances up to 4.4f/sub o/, 6.5f/sub o/, and 8.2f/sub o/ are fabricated and measured to demonstrate the idea.     

The mechanics of compressive kinking in unidirectional fiber reinforced ductile matrix composites

Three distinct stages of kink band formation and propagation exist in ductile matrix composites subjected to compressive loading. These stages are called incipient kinking, transient kinking and kink band broadening. Each stage involves a different deformation mode. The mechanics governing each stage are discussed. Incipient kinking, where the peak load is attained, and kink band broadening, where the load attains a steady-state, are important in structural design. Two design philosophies are presented. References to pertinent literature are made throughout.     

The geometry effects for stress intensity factor of sandwich specimen for measuring interfacial fracture toughness

The interfacial stress intensity factors for three types of sandwich specimens: the single edge crack tensile specimen, the three point bend specimen and the four point shear specimen were obtained by the finite element analysis and compared with the asymptotic solutions. The results show that the geometric effect for mode II specimen is larger than mode I specimen. The limit curves for geometry factor equal to 1.05 were obtained to indicate the usable range of validity of the asymptotic solution.     

2-D dopant profiling in VLSI devices using dopant-selectiveetching: an atomic force microscopy study

We report a detailed mapping of a 2-D dopant profile on a fully processed industrial sample with large dynamic range and high spatial resolution by utilizing a dopant-selective etching process and Atomic Force Microscopy. The experimental results show excellent agreement with those obtained from SRP and SIMS as corroborative methods. We also discuss the most critical factors which influence the applicability, reproducibility, and reliability of this method     

Effect of nitrogen ion implantation on impact wear

The effect of nitrogen ion implantation on the impact wear of several metals and alloys with different hardnesses was studied. An impact testing machine was built for this study. In this machine, bullet-shaped projectiles are bounced against a metal surface which is either stationary or rotating. Wear was determined by weight loss measurements. Scanning electron microscopy pictures were taken to study the surface damage. It was found that nitrogen ion implantation improved the impact wear of most of the materials studied. With sliding motion added during the impact, nitrogen ion implantation has little effect.     

Adaptive 2D finite element simulation of metal forming processes

The development and integration of available current methods and the development of new methods for an adaptive finite element analysis of metal forming processes are presented. The analysis includes large-strain, elastic–plastic, and thermal effects. Many numerical methods such as mesh generation, simulation of the contact between the workpiece and tool and die, and optimization of the finite element mesh are integrated and incorporated. In addition, an algorithm is developed which can detect certain severely distorted elements where the area of integration is approaching zero. The advantage of correcting these regions of locally distorted elements is demonstrated. These numerical methods are implemented in a finite element program developed for simulating metal forming processes, with the emphasis on automating the analysis. Examples include an axisymmetric stress simulation of a coldheading process, a plane strain simulation of an extrusion process and a plane strain simulation of orthogonal metal cutting, all with noticeable thermal effects. The orthogonal cutting forces and feed forces calculated are compared with two sets of experimental data, with good agreement.