Highly reliable a‐IGZO TFTs on a plastic substrate for flexible AMOLED displays

We have successfully reduced threshold voltage shifts of amorphous In–Ga–Zn–O thin‐film transistors (a‐IGZO TFTs) on transparent polyimide films against bias‐temperature stress below 100 mV, which is equivalent to those on glass substrates. This high reliability was achieved by dense IGZO thin films and annealing temperature below 300 °C. We have reduced bulk defects of IGZO thin films and interface defects between gate insulator and IGZO thin film by optimizing deposition conditions of IGZO thin films and annealing conditions. Furthermore, a 3.0‐in. flexible active‐matrix organic light‐emitting diode was demonstrated with the highly reliable a‐IGZO TFT backplane on polyimide film. The polyimide film coating process is compatible with mass‐production lines. We believe that flexible organic light‐emitting diode displays can be mass produced using a‐IGZO TFT backplane on polyimide films.     

Kinetics of the methanation of carbon dioxide over a supported Ni-La2O3 catalyst

The kinetics of the methanation of carbon dioxide was investigated using an alumina supported Ni-La₂O₂ catalyst in a differential and integral reactor. In the differential reactor the molar ratio of H₂ to CO₂ was varied from 0.6 to 30. In the integral reactor the rates were measured with up to 90% conversion. Both reactor tests were carried out at temperatures between 513 and 593 K. The experimental results were described by a Langmuir-Hinshelwood type equation. The kinetics can be explained by assuming equilibrium of dissociative carbon dioxide and hydrogen adsorption, and assuming hydrogenation of surface carbon as the rate determining step.     

Preparation of π-conjugated polymers consisting of 2-decylbenzimidazole and thiophene units and chemical properties of the polymers

Polycondensation by Stille coupling of 2-decyl-4,7-dibromobenzimidazoles and N-methyl-2-decyl-4,7-dibromobenzimidazole with 2,5-bis(trimethylstannyl)thiophene and 5,5′-bis(trimethylstannyl)-2,2′-bithiophene gave the corresponding π-conjugated polymers, poly(2-decylbenzimidazole-4,7-diyl-thiophene-2,5-diyl) 1b, poly(2-decylbenzimidazole-4,7-diyl-bithiophene-2,5-diyl) 1c and poly(N-methyl-2-decylbenzimidazole-4,7-diyl-thiophene-2,5-diyl) 2b, in 98-99% yields. The polymers 1b and 2b were fully soluble in CF₃COOH, and partially soluble in DMF (about 60 and 40% for 1b and 2b, respectively) and NMP (about 70 and 40%, respectively). The NMP soluble part of 1b and DMF soluble part of 2b gave values of 0.36 and 0.24 dl g⁻¹ in NMP and DMF, respectively. The DMF soluble part of 1b, 1c and 2b showed absorption peaks at about 458, 465 and 388 nm, respectively, in DMF. In an alkaline medium the absorption peaks of 1b and 1c are shifted to a longer wavelength by 92-101 nm; the observed shifts in the acidic medium and alkaline medium were much larger than those observed with usual benzimidazoles with low molecular weights. Packing structures of 1b, 1c and 2b are discussed based on their XRD patterns.     

Phase evolution and <110>-orientation mechanism in RTGG-processed BaTiO3 ceramics with electrical properties

The <110>-oriented BaTiO₃ ceramics were fabricated using BaCO₃ matrix and H_1.08Ti_1.73O₄.nH₂O (HTO) template particles, and the mechanism of BaTiO₃ phase formation was investigated. The dielectric, ferroelectric, and piezoelectric properties were also investigated. The transformation of the HTO phase into the TiO₂ bronze or TiO₂ (B) phase was observed at 600°C, where the BaTiO₃ nucleation was accompanied by the formation of a Ba₂TiO₄ phase. The TiO₂ phase reacted with the Ba₂TiO₄ phase at 800°C to give a BaTiO₃ phase, whereas its reaction with the BaTiO₃ resulted in the formation of BaTi₂O₅ phase that got decomposed into BaTiO₃ and Ba₆Ti₁₇O₄₀ phase at sintering temperature ≥1300°C. Sintering with samples’ embedding in BaTiO₃ powders prevented the formation of the Ba₆Ti₁₇O₄₀ secondary phase. The crystallographic orientation along the <110> direction (F₁₁₀) was developed by the epitaxial grain growth mechanism. In addition to the contribution of the grain-size increment for enhancing the F₁₁₀, the preservation of the platelike structure was also found to have a significant impact. The ceramics prepared by the embedded sintering (grain size ≈12.4 µm and F₁₁₀ = 83%) exhibited the room-temperature dielectric constant of 1708 and piezoelectric strain constant of 445 pm/V, which are higher than those of the BaTiO₃ ceramics with randomly oriented grains.     

Measurement of self-diffusion coefficients in Li ionic conductors by using the short-lived radiotracer of 8Li

For the effective use of short-lived radioactive beams, soon to be available at the Tokai Radioactive Ion Accelerator Complex, the authors have developed a radiotracer method for diffusion studies in solids. The experimental test was performed by the measurement of the diffusion coefficients of Li in a sample of the compound βLiAl using an α-emitting radiotracer of ⁸Li (T_1/2=0.84 s). It was found that the time-dependent yields of the α particles from the diffusing ⁸Li that was initially implanted in the sample could be used as a measure of the diffusivity of the tracer in a nondestructive way. The method was applied to measure the self-diffusion coefficients of Li in βLiGa, and for investigating how the Li diffusion in the Li ionic conductors is affected by the concentration of atomic defects (i.e., the existence of the atomic vacancies of Li and the defects in Ga sites that are replaced by Li).     

Clinicopathological significance of intratubular giant macrophages in progressive glomerulonephritis

Very large macrophages, which we have termed "giant macrophages" (G-M phi), have been found in renal tubules, some containing cytoplasmic vacuoles. To elucidate their pathophysiological roles, we examined renal biopsy tissues from various primary glomerulonephritis (GN) and tubulointerstitial nephritis (TIN) using immunohistochemistry with monoclonal antibodies against M phi and other cell surface markers. Giant macrophages were absent or rare in TIN, minimal change nephrotic syndrome, and minor glomerular abnormalities, but G-M phi was plentiful in progressive glomerulonephrides such as IgA nephropathy with crescents, membranoproliferative GN, focal segmental glomerulosclerosis, and especially in crescentic GN. These G-M phi were usually seen in the lumen of renal tubules, but occasionally were found in the Bowman's spaces and glomerular tufts, and similar cells were also found in urine. Moreover, they frequently made contact with tubular epithelial cells expressing intercellular adhesion molecule-1, and the tubular epithelial cells in such lesions often had degenerative changes. Giant M phi may damage tubular epithelial cells from the luminal side. Phenotypically, G-M phi showed activated (CD71+) and mature (25F9+) characteristics along with features of M phi (CD68+), and the cytoplasm contained a great deal of lipids. The numbers of G-M phi in renal tissues closely correlated with the degree of hematuria (rho = 0.5, P < 0.001), serum creatinine value (r = 0.63, P < 0.001) in GN patients (N = 96) and with proteinuria in IgA nephropathy patients (r = 0.89, P < 0.001, N = 27). These data suggest that G-M phi are M phi that were activated and matured in certain active inflammatory sites, which flowed into tubules and then into urine. Thus, the existence of G-M phi in biopsy tissue or urine reflect the activity of GN and may have a predictive value for the progression of GN.     

Stick-slip motion control based on cutter location data for an orthogonal-type robot

In this article, a new desktop orthogonal-type robot, which has the capacity of stick-slip motion control based on cutter location data, is presented for lapping small metallic molds with a curved surface. The robot consists of three single-axis devices with a high position resolution of 1 μm. A thin wooden stick tool with a ball-end shape is attached to the tip of the z-axis. In order to improve the lapping performance, a novel stick-slip motion control method is developed in the control system. The small stick-slip motion is orthogonally generated in the direction of the tool’s movement. The effectiveness of stick-slip motion control is examined through an actual lapping test of an LED lens cavity.