New balance ground relay for parallel four-circuit transmission lines

A 66-kV network generally is grounded through a neutral grounding resistor. In this network a single-phase ground-fault current is limited to as small as 100 to 400 A. There are parallel four-circuit transmission lines mounted on the same tower in the 66-kV network. In such transmission lines, the load and the fault currents could induce circulating current that flows through the lines. Since the circulating current has zero-phase-sequence and negative-phase-sequence components, it could cause unwanted operation of a balance ground relay using zero-phase-sequence current. However, it is difficult to compensate for the circulating current by the conventional vector compensation scheme. This paper presents a new balance ground relay to deal with the circulating current. In the relay from the ground-fault inception until first tripping, the difference current Δ3I_2d of negative-phase-sequence current 3I_2d of the differential current between two protected lines is used as an input current. The Δ3I_2d is the difference current of 3I_2d between, before and during faults. After the first tripping, the difference current of positive-phase-sequence load current and zero-phase-sequence current of the forementioned differential current are used as an input current. Consequently, a higher sensitivity of the ground-fault protection for these lines has been achieved. The correct operation of the new balance ground relay was confirmed when a single-phase-ground-fault occurred in the parallel four-circuit transmission lines, to which the relay is applied.     

Improvement of emission efficiency in polymer light-emitting devices based on phosphorescent polymers

We report improvement of emission efficiency in polymer light-emitting devices (PLEDs) employing phosphorescent polymers. A hole-blocking layer was inserted between the emissive layer and the cathode to enhance recombination efficiency for the injected holes and electrons. Aluminum(III)bis(2-methyl-8-quinolinato)4-phenylphenolato (BAlq) was used for the hole-blocking layer. The resultant PLEDs exhibited significant improvement of emission efficiency. The respective external quantum efficiencies for red, green and blue PLEDs were 6.6, 11 and 6.9%. These values are very high compared with those based on conventional fluorescent polymers.     

Seismic proof test of a reinforced concrete containment vessel (RCCV): Part 2: Results of shaking table tests

A 1/8-scale model was constructed of a reinforced concrete containment vessel (RCCV) used in the latest advanced boiling water reactors (ABWR). Shaking table tests were conducted on it with input motions corresponding to or exceeding a design earthquake assumed for a real Nuclear Power Plant.The objectives of the tests were to verify the structural integrity and the leak-proof functional soundness of the RCCV subjected to design earthquakes, and to determine the ultimate strength and seismic margin by an excitation that led to the model's collapse. The model, the test sequence and the pressure and leak test results were addressed in Part 1. The shaking table test method, the input motions and the test results, including the transition of the model's stiffness, natural frequencies and damping factors and the effects of vertical input motions and internal pressure on the model's characteristics and behavior, the load–deformation, the ultimate strength, the failure mode of the reinforced concrete portion and the liner plate are described here. The seismic safety margin that was evaluated by the energy input during the failure test to a design basis earthquake will be described in Part 3. The analytical results of simulation using the multi-lumped mass model will be described in Part 4.     

Unperturbed dimension of poly(4-acetoxystyrene) measured in good and theta solvents

In order to obtain the additional data concerning the unperturbed dimension of poly-4-substituted styrene, light scattering measurements are performed on the twenty-two fractions with molecular weight of (0.91–352)·10⁴ of poly(4-acetoxystyrene) in dioxan at 25°C, from which the molecular weight obtained was found easily to be evaluated with the gel permeation chromatography using THF. Phase separation experiments for this polymer indicate that the theta state is attained in isopropyl acetate at 19.7°C and butyl acetate at 26.8°C. By making viscosity measurements at that state, the value of K_Θ is directly evaluated as 5.4·10^?4 dl g^?1. The limiting viscosity number is also obtained in good solvents, THF and dioxan, at 25°C and constants of the Mark-Houwink-Sakurada equation in each solvent are determined. Further, approximately the same K_Θ as above is obtained from these data with the Stockmayer-Fixman plot. The calculated value of steric factor, 2.37, on this polymer may be plausible, compared with those of polyvinylaromatic derivatives.     

Formation of alkaline scale in heating brine obtained by the ion-exchange membrane method

Electrodialysis with ion-exchange membranes is one of the most important methods of desalination and salt manufacture. Prevention of scale formation in dialysis cells and evaporators is one of its main problems.This paper discusses the formation of alkaline scale during the process of heating and concentrating brine obtained by electrodialysis with ion-exchange membranes.     

Effect of cleaving environment on the growth of ZnSe on the GaAs (1 1 0) surface by molecular beam epitaxy

Abstracts are not published in this journal This revised version was published online in November 2006 with corrections to the Cover Date.     

Fabrication of conducting poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) thin films by ultrasonic spray-assisted mist deposition method

Transparent conducting polymer, poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) thin films were fabricated by a vapor-deposition technique, ultrasonic spray-assisted mist deposition method. The thickness was well controlled from 40 to 600 nm, keeping reasonable conductivity of 300-450 S/cm. The films with thickness less than 180 nm have high (> 80%) transmission over a wide (270-800 nm) spectral region. In addition, formation of ring-dot electrode pattern with a hard-mask was demonstrated, achieving lithography-less patterning. The results encourage that this deposition method is developed as an actual process technology of transparent electrodes in devices.     

强夯加固饱和软粘土的几个问题探讨

根据最近用强夯加固饱和软粘土的经验,探讨了下列几个问题:用现场试验法确定夯击参数与饱和软粘土的加固效果。饱和软粘土在强夯后的渗透性。它基本符合西德鲁尔大学提出的公式V=Ki~m。根据荷载大小、种类、范围,地基土壤特性及建筑物类型,提出了超夯范围。强夯振动对附近建筑物的影响及减振措施。建议按频率分析法考虑对附近建筑物的影响。     

茅台酒美

茅台酒美,天下同醉.茅台酒美,美在历史、美在文化、美在品质、美在环境；多彩贵州,彩在“茅台”；多美贵州,美在“茅台”.     

Correlation for boiling heat transfer of R-134a in horizontal tubes including effect of tube diameter

A Chen-type correlation for flow boiling heat transfer of R-134a in horizontal tubes was modified taking into account the effect of tube diameter. The effect of tube diameter on flow boiling heat transfer coefficient was characterized by the Weber number in gas phase. Results showed that this correlation could be applied to a wide range of tube diameters (0.5–11-mm-ID). In addition, the dryout point and the heat transfer characteristics after the dryout point were also investigated based on the annular flow model. The proposed experimental expressions to predict both the dryout quality and the post-dryout heat transfer coefficient could also be applied to a wide range of tube diameter (0.5–11-mm-ID).