OTDM transmitter using WDM-TDM conversion with an electroabsorptionwavelength converter

An all-optical multiplexing technique using wavelength division multiplexing (WDM)-time division multiplexing (TDM) conversion with an electroabsorption wavelength converter has been proposed and demonstrated. The effectiveness of this WDM-TDM conversion technique for various pulsewidth settings was experimentally investigated. The fluctuation of the signal performance, which was inevitably caused by the coherent crosstalk between adjacent pulses in the conventional optical time division multiplexing (OTDM) technique, were successfully suppressed, even in the case of wide pulse duration. High Q-factor performance has been maintained for a wide range of duty ration from 36% to 74%. By introducing this technique to the optical time division multiplexer, a highly stable and high-quality 40-Gb/s optical signal can be effectively produced without generating the short pulse or setting two tributaries at orthogonal polarization states, and without introducing high-speed electronics for signal multiplexing. The WDM-TDM conversion with an electroabsorption wavelength converter was extended to 60-Gb/s operation by using three 20-Gb/s tributaries. A clear eye opening was confirmed for a waveform after the WDM-TDM conversion of the 60-Gb/s signal     

Body effects on SAR distributions for microwave exposures in a realistic model of the human head.

The finite-difference time-domain (FDTD) simulations of specific absorption rate (SAR) in a human head exposed to microwaves have, to date, been carried out on models of the head only. This was because it was believed that the body effects on the average SAR of the head could be ignored at high frequencies of around 1 GHz. That opinion, however, was based on inappropriate calculation conditions and is therefore unreliable. In this paper, we have re-examined the body effects on the SAR distributions in a realistic homogeneous model of the adult head exposed to microwaves. We found that the SAR on the eye surface of the head-only model exposed to E-polarized waves was 31% smaller than that of the whole-body model at 900 MHz, and 43% larger at 1.5 GHz. For a size that can practically be considered whole-body, it is necessary to have the top of the head to the belly for 900 MHz and to the chest area for 1.5 GHz. The previously unclear body effects of H-polarized waves were assumed to be less than those of E-polarized waves, suggesting that the chest area would be sufficient for both frequencies.     

Analytical studies of four-inch pipe whip tests under BWR LOCA conditions

The purpose of pipe rupture studies in JAERI is to perform model tests on pipe whip, restraint behavior, jet impingement and jet thrust force, and to establish a computational method for analyzing these phenomena. This report presents the analytical results of 4-inch pipe whip tests under BWR LOCA conditions.Dynamic response analyses were performed using the general-purpose finite element program ADINA. The test pipe was modelled by straight beam elements and the four restraints were modelled by a single truss element. The analytical results were compared with the experimental results. Impact time and maximum total restraint force showed good agreement with experimental results. On the other hand, pipe strain and pipe deflection could not be predicted so well. The reason for this is that the sliding of the restraint during the pipe whip movement cannot be considered in the analyses.     

High-Strength and High-Fracture-Toughness Ceramics in the Al2O3/LaAl11O18 Systems

Control of microstructure in the Al₂O₃/LaAl₁₁O₁₈ system was performed. Elongated alumina grains were formed by doping with small addition of silica, and 20 vol% lanthana- luminate was formed in situ by the reaction of LaAlO₃- A1₂O₃ in an alumina matrix. Strengths of over 600 MPa and a high fracture toughness (6 MPa.m^1/2) were achieved in the material with both elongated A1₂O₃ grains and LaAl₁₁O₁₈ platelets. Generally antagonistic properties such as strength and fracture toughness have been made compatible in the same ceramic system.     

Fracture Energies of Tape-Cast Silicon Nitride with β-Si3N4 Seed Addition

The fracture energies of the tape-cast silicon nitride with and without 3 wt% rod-like β-Si₃N₄ seed addition were investigated by a chevron-notched-beam technique. The material was doped with Lu₂O₃–SiO₂ as sintering additives for giving rigid grain boundaries and good heat resistance. The seeded and tape-cast silicon nitride has anisotropic microstructure, where the fibrous grains grown from seeds were preferentially aligned parallel to the casting direction. When a stress was applied parallel to the fibrous grain alignment direction, the strength measured at 1500°C was 738 MPa, which was almost the same as room temperature strength 739 MPa. The fracture energy of the tape-cast Si₃N₄ without seed addition was 109 and 454 J/m² at room temperature and 1500°C, respectively. On the contrary, the fracture energy of the seeded and tape-cast Si₃N₄ was 301 and 781 J/m² at room temperature and 1500°C, respectively, when a stress was applied parallel to the fibrous gain alignment. The large fracture energies were attributable primarily to the unidirectional alignment fibrous Si₃N₄ grains.     

Formation and Properties of Ln-Si-O-N Glasses (Ln = Lanthanides or Y)

Homogeneous Y-Si-O-N glasses containing 15 or 20 eq% nitrogen (N) were prepared from compositions with Y/Si ratios in the vicinity of that of the lowest eutectic point on the Y₂O₃–SiO₂ phase diagram. The liquidus on the phase diagram shifted toward lower temperatures by incorporation of N. The density, the elastic moduli, and the glass transition temperature of the Y-Si-O-N glasses increased with incorporation of N. This is due to the closer packing of atoms in the glasses by the substitution of N, which is in three-fold coordination with Si, for O which is in two-fold coordination, and the stronger covalent nature of the Si–N bond compared with the Si–O bond. The coefficient of thermal expansion of the Y-Si-O-N glasses increased with increasing Y content, because the discontinuity of the glass network developed with increasing nonbridging anions by the introduction of Y. In contrast, the glass transition temperature and the elastic moduli increased with Y content due to the high coordination of Y for O, and the relatively high cationic field strength of Y. Furthermore, the effect of cationic field strength on properties of Ln-Si-O-N glasses (Ln = lanthanides or Y) is discussed.     

Processing Strategy for Producing Highly Anisotropic Silicon Nitride

Silicon nitride with a preferred orientation of large elongated grains was obtained by tape casting of raw powder slurry seeded with rodlike β-Si₃N₄ particles, followed by a gas pressure sintering under 1 MPa nitrogen pressure. The large elongated grains developed from seeds lay in planes parallel to the casting direction in a two-dimensional distribution. Increased fracture toughness (11.1 MPa·m^1/2) and bending strength (1100 MPa) were achieved in the direction perpendicular to the grains alignment compared to specimens with a random distribution of elongated grains. Morover, the specimens exhibited a high Weibull modulus of 46 due to the uniform distribution of large grains.     

Mechanical Properties of Textured Alumina Made by High-Temperature Deformation

The mechanical properties of a textured alumina made by high-temperature deformation of normal-purity sintered alumina have been investigated. The textured alumina shows very high bending strength and extremely high fracture toughness. Fracture toughness of more than 10 MPa·m^1/2 was measured by the single-edge precracked beam method, and even using the single-edge V-notched beam method, toughness of over 8 MPa·m^1/2 was obtained. This high fracture toughness was attributed to a large number of aligned small platelike grains of the textured structure enhancing the grain bridging effect.     

Generalized measuring-worm algorithm: high-accuracy mapping and movement via cooperating swarm robots

Recently, many extensive studies have been conducted on robot control via self-positioning estimation techniques. In the simultaneous localization and mapping (SLAM) method, which is one approach to self-positioning estimation, robots generally use both autonomous position information from internal sensors and observed information on external landmarks. SLAM can yield higher accuracy positioning estimations depending on the number of landmarks; however, this technique involves a degree of uncertainty and has a high computational cost, because it utilizes image processing to detect and recognize landmarks. To overcome this problem, we propose a state-of-the-art method called a generalized measuring-worm (GMW) algorithm for map creation and position estimation, which uses multiple cooperating robots that serve as moving landmarks for each other. This approach allows problems of uncertainty and computational cost to be overcome, because a robot must find only a simple two-dimensional marker rather than feature-point landmarks. In the GMW method, the robots are given a two-dimensional marker of known shape and size and use a front-positioned camera to determine the marker distance and direction. The robots use this information to estimate each other’s positions and to calibrate their movement. To evaluate the proposed method experimentally, we fabricated two real robots and observed their behavior in an indoor environment. The experimental results revealed that the distance measurement and control error could be reduced to less than 3 %.     

Induction and intracellular localization of a 72-kDa heat shock protein in rat gastric mucosa after water-immersion stress

We investigated the expression and changes in the intracellular localization of a 72-kDa heat shock protein (HSP72) in rat gastric pyloric and fundic mucosa before and after water-immersion stress. Severe mucosal damage was found in the fundic mucosal area of the stomach after this stress. However, no mucosal lesion developed in the pyloric mucosal area. HSP72 in both the soluble and insoluble fractions of the pyloric and the fundic mucosal areas was significantly increased after water-immersion stress, peaking 6h after the initiation of the stress. The increase in HSP72 was more significant in the pyloric mucosal area than in the fundic mucosal area under both normal and stress conditions. The increase of HSP72 in the pyloric mucosal cells occurred prior to the formation of the mucosal lesions, whereas the increase of HSP72 in the fundic mucosal cells was observed after ulcer formation. An immunohistochemical study showed that HSP72 was constitutively expressed in the cytoplasm of the gastric mucosal cells, and that the intranuclear induction of HSP72 was remarkably intense in the pyloric mucosal cells, especially in the proliferative zone, compared with the fundic mucosal cells. Our results may suggest that HSP72 has an important cytoprotective function in gastric mucosal cells and that there is a "biophysical" difference between pyloric and the fundic mucosal cells.