Efficiency Enhancement in Organic Photovoltaic Cells: Consequences of Optimizing Series Resistance

Here, means to enhance power conversion efficiency (PCE or η) in bulk‐heterojunction (BHJ) organic photovoltaic (OPV) cells by optimizing the series resistance (R_s)—also known as the cell internal resistance—are studied. It is shown that current state‐of‐the‐art BHJ OPVs are approaching the limit for which efficiency can be improved via R_s reduction alone. This evaluation addresses OPVs based on a poly(3‐hexylthiophene):6,6‐phenyl C₆₁‐butyric acid methyl ester (P3HT:PCBM) active layer, as well as future high‐efficiency OPVs (η > 10%). A diode‐based modeling approach is used to assess changes in R_s. Given that typical published P3HT:PCBM test cells have relatively small areas (～0.1 cm²), the analysis is extended to consider efficiency losses for larger area cells and shows that the transparent anode conductivity is then the dominant materials parameter affecting R_s efficiency losses. A model is developed that uses cell sizes and anode conductivities to predict current–voltage response as a function of resistive losses. The results show that the losses due to R_s remain minimal until relatively large cell areas (>0.1 cm²) are employed. Finally, R_s effects on a projected high‐efficiency OPV scenario are assessed, based on the goal of cell efficiencies >10%. Here, R_s optimization effects remain modest; however, there are now more pronounced losses due to cell size, and it is shown how these losses can be mitigated by using higher conductivity anodes.     

Dual-Antenna RF CMOS Front-End for Interferer Removal in Ultra-Wideband Systems

Many ultra-wideband (UWB) systems are challenged by strong jammers and narrowband interferers. Using two antennas, we demonstrate a robust UWB radio frequency (RF) front-end design in a 0.25 μm mixed-signal complementary metal oxide semiconductor (CMOS) technology. The proposed realization is capable of adaptively removing a high-power, narrowband interferer early in the receiver chain avoiding front-end saturation and preserving UWB signal power. The early interferer removal resulting in interferer-free demodulation is based on the least mean squares (LMS) algorithm and achieved through a novel combiner low-noise amplifier and noise optimized filtering. Circuit level RF simulations of the proposed circuitry indicate a maximum improvement in signal-to-interference ratio of 39.6 dB.     

FeO0.7F1.3/C Nanocomposite as a High‐Capacity Cathode Material for Sodium‐Ion Batteries

Searching high capacity cathode materials is one of the most important fields of the research and development of sodium‐ion batteries (SIBs). Here, we report a FeO_0.7F_1.3/C nanocomposite synthesized via a solution process as a new cathode material for SIBs. This material exhibits a high initial discharge capacity of 496 mAh g^?1 in a sodium cell at 50 °C. From the 3^rd to 50^th cycle, the capacity fading is only 0.14% per cycle (from 388 mAh g^?1 at 3^rd the cycle to 360 mAh g^?1 at the 50^th cycle), demonstrating superior cyclability. A high energy density of 650 Wh kg^?1 is obtained at the material level. The reaction mechanism studies of FeO_0.7F_1.3/C with sodium show a hybridized mechanism of both intercalation and conversion reaction.     

Mechanical properties of interpenetrating polymer network hydrogels based on hybrid ionically and covalently crosslinked networks

Hydrogels are polymer networks swollen in water. Because of their soft and wet nature, and their ability to show large volume changes, hydrogels can be useful in many biomedical and actuator applications. In these applications, it is crucial to tune the mechanical and physical properties of a hydrogel in a controllable manner. Here, interpenetrating polymer networks (IPNs) made of a covalently crosslinked network and an ionically crosslinked network were produced to investigate the effective parameters that control the physical and mechanical properties of an IPN hydrogel. Covalently crosslinked polyacrylamide (PAAm) or poly(acrylic acid) (PAA) networks were produced in the presence of alginate (Alg) that was then ionically crosslinked to produce the IPN hydrogels. The effect of ionic crosslinking, degree of covalent crosslinking, AAm : Alg and AA : Alg ratio on the swelling ratio, tensile properties, indentation modulus, and fracture energy of IPN hydrogels was studied. A hollow cylindrical hydrogel with gradient mechanical properties along its length was developed based on the obtained results. The middle section of this hydrogel was designed as a pH triggered artificial muscle, while each end was formulated to be harder, tougher, and insensitive to pH so as to function as a tendon‐like material securing the gel muscle to its mechanical supports. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2504–2513, 2013     

Electrochemical routes for environmentally friendly recycling of rare-earth-based (Sm–Co) permanent magnets

Journal of Applied Electrochemistry - The consumption of critical raw materials, especially those in permanent magnets of Nd–Fe–B and Sm–Co-type, has significantly grown in the...     

Emergent membrane-affecting properties of BSA-gold nanoparticle constructs

By adsorbing bovine serum albumin (BSA) on gold nanoparticles (Aunps) with diameters 30 nm and 80 nm, different degrees of protein unfolding were obtained. Adsorption and adlayer conformation were characterized by UV-vis spectroscopy, ζ-potential measurements, steady-state and time-resolved fluorescence. The unfolding was also studied using 1-anilino-8-naphthalene sulfonate (ANS) as an extrinsic probe, showing that BSA unfolds more on 80 nm Aunp than on 30 nm Aunp. Langmuir monolayer studies using two distinct methods of introducing the BSA and BSA-Aunp constructs accompanied with Brewster Angle Microscopy (BAM) and Digital Video Microscope (DVM) imaging demonstrated that BSA-Aunp constructs induce film miscibility with L-α-phosphatidylethanolamine not seen for BSA or Aunp alone. The changes induced by partial unfolding clearly give better film-penetration ability, as well as disruption of liquid crystalline domains in the film, thereby inducing film miscibility. Gold or protein only does not possess the nanoscale film-affecting properties of the protein-gold constructs, and as such the surface-active and miscibility-affecting characteristics of the BSA-Aunp represent emergent qualities.     

Stability of Dye Dispersions in the Presence of Some Eco-Friendly Dispersing Agents

The stability of dye dispersions in the presence of ethoxylated sorbitan lauryl and oleyl esters were reported and compared with dye dispersions containing a conventional dispersing agent, i.e. naphthalene sulfonic acid methylene-bis sodium salt (NSAB). The optimum operating conditions obtained using a central composite design and stability of dye dispersions were evaluated by a turbidimetry method. Results showed that the dose of surfactants and the temperature of operation were important factors in preparing stable dye dispersions. Also, the best conditions for preparing dye dispersions were as follows: dose of surfactant 0.05 g, temperature 25 °C and time 5 min. In addition to, findings indicated that both of the used surfactants had better performance in dispersing the dyes in water. However, ethoxylated sorbitan oleate had better efficiency relative to other used dispersing agents. The performance of both sorbitan esters were compared with NSAB. The results indicated that they can create stable dye dispersions in aqueous media and have approximately the same effectiveness with NSAB. In this series, although oleate ester had a better performance than the laurate, the difference in performance of using dispersing agents was not significant. This finding was confirmed by the results of the particle size analysis of dye dispersions.     

Personalisierte Medizin als Orphanisierung: rechtliche und ethische Fragen

Definition of the problem The development of personalized medicine is currently a popular topic. Particularly the personalized pharmacotherapy is a matter of relative importance due to pharmacological and molecular–genetic developments. For this reason it is required to examine the implications of personalized pharmacotherapy to statutory health insurance and health care of patients. Arguments In this context the question of orphanization arises: If medical drugs of personalized medicine could be regularly indicated as orphan drugs, i.e., as drugs to medicate orphan diseases, it would not be necessary according to the “Arzneimittelneuordnungsgesetz” (AMNOG) to prove an auxiliary value within the assessment of the “Gemeinsamer Bundesausschuss” (GBA). Crucial to the drug’s indication as an orphan drug is among other things the rate of prevalence of the patient group, whose disease should be medicated with the drug. In this connection, there is importance attached to the stratification of patient groups within personalized medicine. Conclusion An orphanization causes consequences in terms of prices to the statutory health insurance due to the lack of knowledge about an auxiliary value. For patients, the implications must be considered in a more differentiated manner.     

Developing electrochemical measurements in order to assess anti-corrosive coatings more effectively

The aim of this project was to check reproducibility of results obtained using NOCS (no connection to the substrate) arrangement of the electrochemical noise method (ENM). NOCS involves taking measurements from three nominally identical areas on the coated surface. Thus, no electrical connection to substrate is required. In practice the areas are not identical and various arrangements for connection of the three cells were tried to see if the individual areas could be separated out and whether the individual resistances could be computed. Also different ways of calculating the R_n (noise resistance) and R_sn (spectral noise resistance) parameters were attempted to see which one gave the best comparison with the more standard EIS measurements. The maximum entropy method was recognized to be the most useful for comparison with EIS, as well as for graphic evaluation of results. Regarding distinguishing three areas using different connection arrangements, it was possible to identify the situation when one of the three values was different to the other two. However further experiments are needed before it will be possible to confidently assign an R_n value to each individual area.