Performance improvement of zinc oxide photoanode-based dye-sensitized solar cells by multi-walled carbon nanotube

Unique electrical and surface-to-volume properties of carbon nanotubes have made these conductive molecules highly attractive in many applications. In this work, the influence of multi-walled carbon nanotubes into a zinc oxide active layer of dye-sensitized zinc oxide solar cell has been investigated. With this method, a significant improvement in the performance of the solar cell has been achieved. Compared to the typical zinc oxide photoelectrochemical cells, the photocurrent-voltage characteristics of the fabricated cell containing 0.05 percent by weight of carbon nanotubes in the metal oxide film displayed a higher short-circuit photocurrent, consequently caused an increase of the solar-to-electricity conversion efficiency by a factor of approximately 1.4. Further increase of the conductive carbon material resulted in a decrease of the energy conversion of the photovoltaic cell. The enhancement of the energy conversion at this optimum carbon nanotube loading may be attributed to the dye-adsorption ability and the electrochemical activity of the composite photoanodes. The fabricated photovoltaic cells with the highest efficiency exhibited the maximum dye adsorption intensity and the minimum charge transfer resistance, as measured by ultraviolet-visible spectroscopy and electrochemical impedance spectroscopy, respectively.     

An artificial nose based on M-porphyrin (M = Mg, Zn) thin film and optical spectroscopy

Artificial nose has recently become an emerging instrument for quality assurance in the food industry. These paper present the optical gas sensors based on Magnesium-5, 10, 15, 20-tetra phenyl-porphyrin (MgTPP) and Zinc-5, 10, 15, 20-tetra phenyl-porphyrin (ZnTPP) thin films and their application as an artificial nose. Based on the measurement of optical absorbance response using a general UV-Vis spectroscopy, this artificial nose was tested to discriminate various volatile organic compounds (VOCs) and Thai beverages. Atomic force microscopy (AFM) and X-rays diffraction (XRD) were used to confirm the polycrystalline structure of the sensing materials. Density functional theory (DFT) calculations reveal that MgTPP interacts more strongly with the VOCs than ZnTPP, especially with methanol. The classification results of VOCs and Thai beverage vapors using the principal component analysis indicate that both MgTPP and ZnTPP-based artificial noses can be an efficient tool for quality assurance of alcoholic beverages.     

Nanostructured surfaces from size-selected clusters

The deposition of ionized beams of size-selected atomic clusters onto well-defined substrates represents a new method of preparing nanostructured surfaces, with lateral feature sizes in the range 1-10 nm. 'Pinning' of the incident clusters prevents the diffusion of the clusters on the surface, and thus preserves the gas-phase cluster size, even at room temperature and above. At the same time, advances in diblock copolymer techniques allow the preparation of ordered two-dimensional arrays of clusters. Here we discuss the creation and applications of these nanostructured surfaces, ranging from the fabrication of semiconductor nanostructures to the immobilization of protein molecules.     

Effects of tetramethylene sulfone solvent additives on conductivity of PEDOT:PSS film and performance of polymer photovoltaic cells

A solvent additive in PEDOT:PSS solution is one of many methods to improve the conductivity of the poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films. We explore a new type of the solvent additive, namely tetramethylene sulfone (TMS), for the fabrication of the PEDOT:PSS conductive layer in the ITO/PEDOT:PSS/P3HT:PCBM/TiO_x/Al polymer photovoltaic cells, in comparison to a more common dimethyl sulfoxide (DMSO) solvent additive. At optimal conditions, the TMS additive at 10 wt.% has been found to enhance the conductivity of pristine PEDOT:PSS films from 0.04 S/cm up to approximately 189 S/cm, compared with the highest conductivity for the case of the DMSO additive at 15 wt.% of 117 S/cm. Possible mechanisms of this conductivity enhancement, relating to the polymer conformation and the film morphology, have been investigated by Raman spectroscopy, X-ray diffraction, atomic force microscopy, and transmission electron microscopy. The performance of the polymer photovoltaic cells fabricated with the solvent additives PEDOT:PSS films follows a similar trend to the conductivity of the films as a function of the additive concentration. The additives mainly lead to greater short circuit current density (J_sc) of the photovoltaic cells. The highest power conversion efficiency (PCE) of 2.24% of the device has been obtained with the 10 wt.% TMS additive of, compared to the PCE of 1.48% for the standard device without solvent additive.     

Effect of trichlorobenzene additive on the performance and morphology of polyfluorene and fullerene derivative bulk heterojunction solar cells

The influence of additive, namely 1,3,5‐trichlorobenzene (TCB), on the morphology and performance of bulk heterojunction (BHJ) organic solar cells was studied based on a 1:2 (w/w) blend of benzothiadiazole/thiophene‐based copolymers (PFTBzTT) to [6,6]‐phenyl‐C₆₁ butyric acid methyl ester (PCBM). The active layers were deposited by spin‐coating from solutions using chloroform, with different additive concentrations from 0 to 36 mg/ml. The addition of solvent additive into the polymer solution was able to improve the performance of BHJ solar cells. The maximum power conversion efficiency (%PCE) of 0.85% was obtained for a cell with the TCB concentration of 12 mg/ml after annealing at 180°C for 20 min. From atomic force microscopy (AFM) images, the films processed without TCB appear smoother than those with the TCB additive. A large extent of segregation was also observed in the films processed with a high TCB concentration. The optical images of the thin films suggest that the optimum concentrations of the additive cause the polymer self‐organisation, resulting in some aggregation of large PCBM crystals. © 2011 Canadian Society for Chemical Engineering     

Effect of gas-timing technique on structure and optical properties of sputtered zinc oxide films

Zinc oxide thin films were prepared by the RF magnetron sputtering using a gas-timing technique whereby the flow of argon into the sputtering chamber was controlled by an on–off sequence. With this technique, polycrystalline ZnO thin films on glass substrates have been achieved without any thermal treatment of the substrate. In addition, the RF power and the gas-timing sequence can be fine-tuned to produce the hexagonal structure of ZnO thin films. X-ray diffraction (XRD) measurements confirm a (0 0 2) plane oriented wurtzite structure ZnO thin films. The optimized conditions for this hexagonal structure are an RF power of 30 W and an on–off gas-timing sequence of 50:2 s. The root mean square surface roughness of ZnO thin films measured by atomic force microscopy are in the range of 6.4–11.5 nm. The optical transmittance of ZnO thin films is over 85% in the visible range.