End‐Capping as a Method for Improving Carrier Injection in Electrophosphorescent Light‐Emitting Diodes

The electronic properties, carrier injection, and transport into poly(9,9‐dioctylfluorene) (PFO), PFO end‐capped with hole‐transporting moieties (HTM), PFO–HTM, and PFO end‐capped with electron‐transporting moieties (ETM), PFO–ETM, were investigated. The data demonstrate that charge injection and transport can be tuned by end‐capping with HTM and ETM, without significantly altering the electronic properties of the conjugated backbone. End‐capping with ETM resulted in more closely balanced charge injection and transport. Single‐layer electrophosphorescent light‐emitting diodes (LEDs), fabricated from PFO, PFO–HTM and PFO–ETM as hosts and tris[2,5‐bis‐2′‐(9′,9′‐dihexylfluorene)pyridine‐κ²NC_3′]iridium(III ), Ir(HFP)₃ as the guest, emitted red light with brightnesses of 2040 cd m^–2, 1940 cd m^–2 and 2490 cd m^–2 at 290 mA cm^–2 (16 V) and with luminance efficiencies of 1.4 cd A^–1, 1.4 cd A^–1 and 1.8 cd A^–1 at 4.5 mA cm^–2 for PFO, PFO–HTM, and PFO–ETM, respectively.     

Transcutaneous balloon angioplasty in the treatment of subclavian steal syndrome. Characteristics of vertebral basal flow with transcranial Doppler technique

Subclavian steal syndrome (SSS) appears when the origin of the subclavian artery (SA) is occluded or stenosed. Introduction of transcranial Doppler sonography (TCD) provided an opportunity to evaluate parameters of the blood flow in the vertebral (VA) and basilar artery (BA). Measurements of blood flow velocities performed at rest and after the brachial hyperemia test allow one to classify hemodynamic types of SSS. The aim of the study was to categorize types of steal and to compare the differences of flow patterns before and after percutaneous transluminal SA balloon angioplasty (SA-PTA). Fourty-eight patients with angiographically confirmed SSS (aged from 27 to 68 years, mean 53; 2/1 f/m ratio) were examined with 2 MHz range-gated, pulsed transcranial Doppler device (TC 2-64B EME). Both VA and BA were evaluated by the transoccipital approach at rest and during the brachial hyperemia. In 5 cases (10.4%) permanent reversal blood flow in the BA was observed (complete basilar steal). In flow in the BA blood flow was in the normal direction at rest and altered (reversed or decreased) when induced with brachial hyperemia test (transient basilar steal). In the next 14 patients (29.2%) permanently reversed VA blood flow was observed with only a slight or no alterations of the BA flow after the hyperemia test (complete vertebral steal). In the last 19 cases (39.6%) alterations of the VA blood flow without changes in BA flow were observed (latent vertebral steal). Between 1991 and 1994 twenty seven symptomatic patients with different hemodynamic types of SSS were treated with SA-PTA. TCD evaluation of VA's and BA using the hyperemia test was performed before, 3 to 7 days and 3 months after morphologically and hemodynamically successful subclavian artery balloon PTA. Normal results of vertebrobasilar examinations were obtained in 26 cases after this procedure. In one case the latent vertebral steal was detected. The 28 months mean follow-up revealed no significant changes in TCD flow patterns recorded from VA's and BA. After collecting data of about 60 patients with SSS we examined with TCD we conclude that: in patients with a hemodynamically significant SA stenosis the presence of reversed ipsilateral VA blood flow (a radiologic steal) its not a good determinant of either the presence or type of presenting symptoms and after successful PTA or recanalisation and PTA of SA in almost all cases we examined close to normal TCD recordings in BA and VA.     

ISDN and new services in Poland: opportunities and obstacles

Presents an overview of problems involved in introducing ISDN and new services in the public network of Poland. The technical aspects of the assumed network and services development strategy are considered. The focus is on development alternatives and the process of establishing national requirements for the development     

Response correction techniques for surrogate‐based design optimization of microwave structures

Simulation‐based optimization has become an important design tool in microwave engineering. However, using electromagnetic (EM) solvers in the design process is a challenging task, primarily due to a high‐computational cost of an accurate EM simulation. In this article, we present a review of EM‐based design optimization techniques exploiting response‐corrected physically based low‐fidelity models. The surrogate models created through such a correction can be used to yield a reasonable approximation of the optimal design of the computationally expensive structure under consideration (high‐fidelity model). Several approaches using this idea are reviewed including output space mapping, manifold mapping, adaptive response correction, and shape‐preserving response prediction. A common feature of these methods is that they are easy to implement and computationally efficient. Application examples are provided. © 2011 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2012.     

Multilevel microwave design optimization with automated model fidelity adjustment

A computationally efficient algorithm for electromagnetic (EM)‐simulation‐driven design optimization of microwave structures is proposed. Our technique exploits variable‐fidelity EM simulations and the multilevel design approach where an approximate optimum of the lower accuracy but faster EM model of the structure under design is used as a starting point for optimizing a more accurate model. Several enhancements of the basic multifidelity method are introduced, including an efficient algorithm of optimizing EM models that is based on local response surface approximations, as well as automated adjustment of model fidelity. Convergence of the procedure to the optimum design is ensured by defaulting to the higher fidelity model whenever the prediction given by the lower fidelity fails to improve the design. Distribution of the computational effort between the models of different fidelity allows for making larger steps in the design space at a low cost, as well as substantial reduction of the number of high‐fidelity model evaluations, because the high‐fidelity model is only referred to in the last design stage. The article provides comprehensive numerical verification of our technique. Substantial computational savings are demonstrated in comparison to the benchmark methods: over 40% on average as compared to a basic version of the multifidelity optimization approach and over 95% as compared to direct optimization of the high‐fidelity model. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:281–288, 2014.     

Oligomer and Polymer Formation in Hexamethylcyclotrisiloxane (D<Subscript>3</Subscript>) – Hydrosilane Systems Under Catalysis by tris(pentafluorophenyl)borane

Summary Reactions of hexamethylcyclotrisiloxane, D₃, with 1,1,3,3-tetramethyldisiloxane, ^HMM^H, 1,1,1,3,3-pentamethyldisiloxane, ^HMM, phenyldimethylsilane and phenylmethylsilane catalyzed by tris(pentafluorophenyl)borane were studied. These reactions lead to ring opening of D₃ by the SiH reactant producing open chain oligomers with hydrosilane functionality at one or both chain ends. The reactivity of the hydrosilanes toward D₃ decreases in the series: PhMeSiH₂ > ^HMM^H > PhMe₂SiH > ^HMM. Competitive self-oligomerization of ^HMM^H and ^HMM also occurs. Primary products of these processes are able to enter into reactions with the SiH and D₃ reactants; some also undergo cyclization. Thus, consecutive and competitive processes lead to a series of various oligohomologues. Gas chromatography in conjunction with chemical ionization mass spectroscopy permitted identification of structure and determination of the basic directions of these oligomerization processes. Polysiloxanes of higher molecular weight may be also formed in some of these systems. The reactions, which occur in the systems studied, are rationalized on the basis of the mechanism involving the hydride transfer from silicon to trivalent boron. This includes the transient formation of tertiary trisilyloxonium borate which decomposes by the hydride transfer to one of the silicon atoms of the trisilyloxonium center. Footnote: This paper is dedicated to Professor Ian Manners in recognition of his significant contributions to the field of organometallic polymers.     

Electroreduction of laccase covalently bound to organothiol monolayers on gold electrodes

Cerrena unicolor laccase was immobilized on the gold electrode by covalent bonding to self-assembled monolayers of mercaptoundecanoic or mercaptopropionic acids. STM images of immobilized laccase proved high population of the laccase molecules on the monolayer modified electrode. The SERS experiments in concert with resonance Raman effect confirmed that the structure at the “blue” copper site of the immobilized protein remained intact. The accessibility of individual copper sites for electron exchange with the gold electrode surface was investigated by voltammetry. The electrode behavior of laccase is different in the presence and absence of oxygen, showing that the immobilized enzyme is reactive towards oxygen. Addition of two common mediators improved the electrical connectivity of the enzyme with the electrode, increased the catalytic efficiency of immobilized laccase and switched the onset of catalytic current to the potentials of the mediator. Immobilization of laccase on well-organized mercaptoundecanoic acid separates efficiently the enzyme from the electrode and does not allow easy access of mediators to the surface. Attachment of the enzyme at smaller distance from the electrode by means of significantly shorter spacer molecule—mercaptopropionic acid improved the efficiency of catalytic reduction of oxygen on the monolayer modified electrode.     

Precise control of reflection response in bandwidth‐enhanced planar antennas

In this work, the issues of bandwidth enhancement of planar antennas and the relevance of precise and automated response control through numerical optimization have been investigated. Using an example of a planar antenna with parasitic radiator we illustrate possible effects of even minor modifications of the antenna geometry (here, applied to the ground plane) on its reflection performance. In particular, a proper handling of geometry parameters may lead to considerable broadening of the antenna bandwidth. For the sake of computational efficiency, the adjustment of geometry parameters is carried out using surrogate‐based optimization methods exploiting coarse‐discretization EM simulations as the underlying low‐fidelity antenna model. Additionally, suitably defined penalty function allows us to precisely control the maximum in‐band reflection so that sufficient margin to accommodate possible manufacturing tolerances can be achieved. The optimized designs of the two antenna structures considered in this work exhibit over 1.75 GHz (>31%) and 2.15 GHz (>38%) bandwidth, respectively, for the center frequency of 5.6 GHz. Simulation results are validated using measurements of the fabricated prototypes. Comparison with state‐of‐the‐art designs is also provided. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:653–659, 2016.     

Path Loss Modelling for Location Service Applications

The aim of this paper is the path loss modelling for the radiolocation services in radio communication networks, particularly in cellular networks. The main results of the measurements obtained in the physical layer of the UMTS are introduced. A new method for the utilization of the multipath propagation phenomenon to improve the estimation of the distance between the MS （mobile station） and the BS （base station） is outlined. This method significantly increases the quality of location services in systems which use a radio interface with DS （direct sequence） CDMA （code division multiple access）.