排序方式: 共有73条查询结果,搜索用时 15 毫秒
1.
Mohammad Mohammadi Ahmad Ramazani SaadatAbadi Shohreh Mashayekhan Reza Sanaei 《应用聚合物科学杂志》2020,137(40):49219
Peripheral nerve injuries remain among the most challenging medical issues despite numerous efforts to devise methods in fabrication of nerve conduits to functionally regenerate axonal defects. In this regard, the current study offers a holistic perspective in design by considering the mechanical, topographical and structural aspects which are crucial for a successful nerve guide conduit. Poly(e-caprolactone) and gelatin were employed to serve this purpose in the form of dual-electrospun films which were rolled and later shaped the assembly of a multichannel conduit. Polyaniline/graphene (PAG) nanocomposite was incorporated to endow the conduit with conductive properties. FTIR analysis, water contact angle measurements, and SEM observations as well as mechanical and conductivity tests were used to evaluate the properties of the conduits. In addition, MTT assay was conducted to assess the proliferation of rat bone marrow-derived mesenchymal stem cells cultured on the films. Incorporating 2% PAG proved to have superior cell support and proliferation, while guaranteeing electrical conductivity of 10.8 × 10−5 S/cm and remarkable tensile strength of 3.52 ± 1.3 MPa and 14.12 ± 3.1 MPa for wet and dry conditions, respectively. Overall, the observed results highlight the great potential of the fabricated conduit to be used as a candidate for peripheral nerve defects. 相似文献
2.
Template‐Directed Directionally Solidified 3D Mesostructured AgCl–KCl Eutectic Photonic Crystals
下载免费PDF全文
![点击此处可从《Advanced materials (Deerfield Beach, Fla.)》网站下载免费的PDF全文](/ch/ext_images/free.gif)
3.
Photonic Crystals: Template‐Directed Directionally Solidified 3D Mesostructured AgCl–KCl Eutectic Photonic Crystals (Adv. Mater. 31/2015)
下载免费PDF全文
![点击此处可从《Advanced materials (Deerfield Beach, Fla.)》网站下载免费的PDF全文](/ch/ext_images/free.gif)
4.
Synthesis and Spark Plasma Sintering of Mg2Si Nanopowder by Mechanical Alloying and Heat Treatment
下载免费PDF全文
![点击此处可从《International Journal of Applied Ceramic Technology》网站下载免费的PDF全文](/ch/ext_images/free.gif)
Mohammad Khajelakzay Saeed Reza Bakhshi Gholam Hossein Borhani Mazaher Ramazani 《International Journal of Applied Ceramic Technology》2016,13(3):498-505
In this investigation, a two‐step method for the preparation of magnesium silicide (Mg2Si) nanopowder was studied. This method is known as mechanical alloying followed by heat treatment. The results showed that the compositions of the combustion products depended on the milling time, heat treatment temperature, and starting mixtures. Pure Mg2Si nanopowder was formed after short milling time and heat treatment, from Mg and Si powders with the mole ratio of 2.1:1 (Mg:Si) at 500°C in Ar atmosphere. Using the Mg2Si nanopowder, Mg2Si ceramic was produced by spark plasma sintering at 800°C under 50 MPa for 15 min. Composition and structure of reactants and products were examined by X‐ray diffraction (XRD), field emission scanning electron microscopy (FE‐SEM) and high‐resolution transmission electron microscopy (HR‐TEM). 相似文献
5.
M. J. Ramazani‐Harandi M. J. Zohuriaan‐Mehr A. A. Yousefi A. Ershad‐Langroudi K. Kabiri 《应用聚合物科学杂志》2009,113(6):3676-3686
The swelling properties of superabsorbent polymers (SAPs) under real conditions are extremely important for selecting the material suitable for a given application, e.g. feminine napkin or agriculture. This new practical research represents deeper synthetic and physicochemical studies on the structure–property relation in acrylic SAP hydrogels and composites. Thus, the values of saline‐absorbency under load (AUL; a measurable simulation of the real circumstances of SAP applications, at pressures 0.3–0.9 psi) were measured for the SAP or SAP composite samples prepared under different conditions, i.e. type and content of crosslinker, type and concentration of initiator, percentage of inorganic filler (kaolin), and type and percentage of porosity generators. The samples were subsequently used to determine the rheological and morphological characteristics. Dynamic storage modulus (G′) measurements were carried out at constant strain in a wide range of frequency. Linear correlations were frequently found to be active between AUL and G′ data over the rubber‐elastic plateau. Thus, for a given SAP: AUL = ktotalG′ + C. The coefficient k total is a function of (nature and content of crosslinker, initiator, inorganic component, particle morphology, etc.). Therefore, the easily measured AUL values could be simply correlated to the main synthesis variables and molecular structure of SAP gels through a rheological material function (G′). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009 相似文献
6.
Laser surface nitriding of Ti–6Al–4V alloy was carried out with a Nd:YAG pulsed laser. The microstructure and corrosion behaviour of the nitrided samples were examined, using SEM, XRD, XPS, and anodic polarization tests in 2 M HCl solution. Laser nitriding produced a thin continuous TiN layer followed by TiN dendrites and TiN0.3 needles. The laser nitrided specimen exhibited less corrosion current density, passivated more readily and also, maintained a lower current density over the duration of the experiment. This was correlated with the formation of very thin, continuous TiNxOy film, which could retard chloride ions ingress into the substrate. 相似文献
7.
A processing method called “accelerated mild anodization” is developed for preparation of high density and uniform nanoporous by anodization of aluminum. The idea is to use two different temperatures for both sides of sample in order to maintain mid level of current density during the anodization process. Here we have used high temperature for the back side of the sample in order to increase the current density while the electrolyte is kept at low temperature in the level of mild anodization. It is shown that not only the film growth is considerably fast, almost ten times faster than mild anodization, but also the anodization voltage is constant and anodization current variation is much less compared to hard anodization technique. Using oxalic acid, interpore distances of 89, 104, 117 and 130 nm were obtained for 35, 40, 45 and 50 V anodization voltages, respectively. It is found that the interpore distances are proportional to the anodization potential, almost same as that for the mild anodization. The porosity obtained tended to obey the same rule as that in mild anodization. This method is promising for industrial application due to short fabrication time as well as high-speed pore ordering. 相似文献
8.
Ebrahim Ahmadi Mehdi Nekoomanesh Haghighi Zahra Mohamadnia Ali Ramazani 《应用聚合物科学杂志》2010,118(6):3658-3665
Cr/SBA‐15 catalysts were prepared by the grafting of chromium nitrate nonahydrate [Cr(NO3)3·9H2O] complexes onto SBA‐15 mesoporous materials. Shish‐kebab and nanofiber polyethylenes (PEs) were prepared under different temperatures via ethylene extrusion polymerization with the Cr(NO3)3·9H2O catalytic system. The diameter of a single nanofiber was 100–250 nm. Scanning electron microscopy images showed that the polymer obtained from the SBA‐15‐supported catalyst under different polymerization temperatures produced nanofiber and/or shish‐kebab morphologies. X‐ray diffraction and differential scanning calorimetry were used to characterize microstructures of the materials. Polymers obtained with all of the catalysts showed a melting temperature, bulk density, and high load melt index; this indicated the formation of linear high‐density PE. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010 相似文献
9.
Ali Dashti Ahmad Ramazani SA Yuichi Hiraoka Sang Yull Kim Toshiaki Taniike Minoru Terano 《Polymer International》2009,58(1):40-45
BACKGROUND: Kinetic and morphological aspects of slurry propylene polymerization using a MgCl2‐supported Ziegler–Natta catalyst synthesized from a Mg(OEt)2 precursor are investigated in comparison with a ball‐milled Ziegler–Natta catalyst. RESULTS: The two types of catalyst show completely different polymerization profiles: mild activation and long‐standing activity with good replication of the catalyst particles for the Mg(OEt)2‐based catalyst, and rapid activation and deactivation with severe fragmentation of the catalyst particles for the ball‐milled catalyst. The observed differences are discussed in relation to spatial distribution of TiCl4 on the outermost part and inside of the catalyst particles. CONCLUSION: The Mg(OEt)2‐based Ziegler–Natta catalyst is believed to show highly stable polymerization activity and good replication because of the uniform titanium distribution all over the catalyst particles. Copyright © 2008 Society of Chemical Industry 相似文献
10.
The purpose of this study was the production of copolymers and terpolymers with highly hydrophilic–hydrophobic properties, using inexpensive and available monomers as potential enhancing oil recovery (EOR) and water production control agents for high-temperature and high-salinity (HTHS) oil reservoirs. For this purpose, several copolymers and terpolymers with different molar percentage of acrylamide/styrene, acrylamide/maleic anhydride, and acrylamide/styrene/maleic anhydride were synthesized by the inverse emulsion polymerization technique. The presence of hydrophobic styrene and hydrophilic maleic anhydride monomers in the copolymer and terpolymer structure, provided some unique properties compared to polyacrylamide, was confirmed by several analyses including HNMR, elemental analysis, FTIR, SEM, TGA, and DSC. Simulating HTHS oil reservoir condition under high salinity, temperature, and shear rate, the rheological studies suggested unlike traditional EOR agents such as polyacrylamide, the viscosity of the copolymer, and terpolymer aqueous solutions showed a considerable increase after a critical polymer concentration and less reduction with the salt increment at both ambient and elevated temperatures. Furthermore, the swelling ratio of the insoluble terpolymers measured versus the time and temperature in salt water increased with the maleic anhydride mole fraction, decreased with the salt concentration, and showed a maximum value at around 57 °C. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47753. 相似文献