Gastric antrectomy with selective gastric vagotomy does not influence gallbladder motility during interdigestive and postprandial periods

Fasting gastrointestinal motility and gallbladder motility during the interdigestive state and in the postprandial period was studied in eight patients who were operated for ulcer disease with an antrectomy and selective gastric vagotomy. Nocturnal motility recording revealed all three phases of the migrating motor complex (MMC) in all but one patient, where no phase III activity was recorded. In the rest of the patients 3-10 events with phase III activity were recorded. At scintigraphy ([75Se]HCAT) a cyclic gallbladder filling and emptying in relation to the MMC cycle was found. Episodes with emptying were confined to phase II and a total of 13 episodes with a median duration of 25 min (range 10-70 min) were observed. A median of 10.7% (6.1-17.7%) of the gallbladder contents was emptied. In a control group of eight healthy young men the values were 13.5 min (9-36 min) and 6.9% (3.7-31.1%), respectively. These differences were not significant. During the postprandial period, a lag period in gallbladder emptying of median 15 min (5-20 min) was observed when food ingestion took place during phase I of the MMC. Thereafter a gradual emptying occurred with a rate of 0.95% min (0.71-1.15%/min). In a control group of healthy young males, the lag period was 13.5 min (9-22.5 min) and the emptying rate 0.61%/min (0.08-0.77%/min). When food ingestion occurred during phase II of the MMC, the lag period of gallbladder emptying in the patient group was median 0 min (0-5 min) and the emptying rate was 0.77%/min (0.33-0.86%/min). The values in the control group were 0 min (-9 to 13.5 min) and 0.76%/min (0.54-2.25%/min), respectively. These differences between the patients and controls were not significant. In conclusion, antrectomy and selective gastric vagotomy do not influence fasting gastrointestinal motility or gallbladder motility during the interdigestive state or in the postprandial period.     

Measurement of the particle movement in the fountain region of a Wurster type bed

A non-intrusive technique to follow single particles in the fountain region of a spouted bed with draft tube, the Wurster coater, is developed and tested. Compared to other techniques found in literature, the measurement technique presented here is easy to handle, inexpensive and suitable for particles with a diameter down to 500 μm. The measurements are performed in a laboratory scale Wurster bed constructed of Plexiglas to allow optical access to the flow. A small quantity of the particles in the bed are marked with fluorescence. A UV lamp is used to excite the fluorescence and the marked particles are followed with a high-speed video camera equipped with an optical filter. A single marked particle in the fountain can be followed in 5-30 images in sequence at a frame rate of 125 fps. The particle position and velocity are calculated. The distribution of the particle trajectories maximum height is studied for different particle loading, jet air velocity and position of the Wurster tube. The technique can be used for the characterization of differences in process dynamics due to different operating conditions.     

Ammoxidation of toluene over Y-Ba-Cu-Co-O perovskites

Ammoxidation of toluene over the perovskites YBa₂Cu₃O_6.1, YBa₂Cu₂CoO_6.7 and YBaCuCoO_4.9 was investigated at 400 °C. At low partial pressures of O₂ benzonitrile was selectively formed, while CO₂ was the main product at high pressures of O₂. Systematic differences in activity were observed for the three phases and are related to the crystal contents of Cu and Co. At low O₂ pressures, Cu-sites are active for nitrile formation, while Co-sites give CO₂. At high O₂ pressures, the activity for CO₂ of Cu-sites increases more than that of Co-sites due to filling of near-surface oxygen vacancies.     

A new device for coating single particles under controlled conditions

A new device for coating a single levitated particle in a controllable environment is designed and tested. This enables fluidized bed processing to be simulated experimentally on a single-particle level. The device consists of a coating chamber, which contains a capillary tube for levitating the particle, a micro-dispenser for producing discrete drops of controlled size and velocity and a device for supplying gas with specified temperature and humidity. The coating chamber consists of two parts, a confined space where the particle is levitated and a droplet insertion cone where the coating solution is injected into the particle suspending gas flow. A capillary with a well-defined diameter connects the droplet insertion cone and the area where the particle is levitated. The device is equipped with a piezo-actuated flow-through micro-dispenser that has the ability to produce discrete droplets with high reproducibility in terms of droplet size and velocity. The gas required for the coating process is taken from a gas container where the water content is analysed and kept at a minimum. A liquid flow is then introduced into the gas flow at a well-defined flow rate, mixed and evaporated in a three-way mixing vault. The humidified gas flow is then split into two separate flows; a suspending gas flow and a protecting gas flow for the inside of the coating chamber. The device is equipped with a high-speed video camera for monitoring both droplet production and droplet impact. Temperatures and flow rates throughout the device are measured and logged. Preliminary results show the influence of solvent, gas quality and coating procedure on the quality of the coating.     

Neck postures in air traffic controllers with and without neck/shoulder disorders

Prolonged computer work with an extended neck is commonly believed to be associated with an increased risk of neck-shoulder disorders. The aim of this study was to compare neck postures during computer work between female cases with neck-shoulder disorders, and healthy referents. Based on physical examinations, 13 cases and 11 referents were selected among 70 female air traffic controllers with the same computer-based work tasks and identical workstations. Postures and movements were measured by inclinometers, placed on the forehead and upper back (C7/Th1) during authentic air traffic control. A recently developed method was applied to assess flexion/extension in the neck, calculated as the difference between head and upper back flexion/extension. Results: cases and referents did not differ significantly in neck posture (median neck flexion/extension: -10 degrees vs. -9 degrees ; p=0.9). Hence, the belief that neck extension posture is associated with neck-shoulder disorders in computer work is not supported by the present data.     

The effect of decision-making training: results from a command-and-control training facility

The purpose of this study was to investigate whether training in a microworld had an effect on the decision-making process in a command-and-control training facility. Fourteen battalion commanders participated in the study. Prior to performing the main task in the command-and-control facility, seven participants (the experimental group) received training in the microworld. Seven participants (the control group) received no training before the main task. The results show that the experimental group performed better than the control group, measured by self-ratings and by fulfilling the instructors’ criteria. The experimental group displayed a different decision-making behaviour in the main task than the control group did. The results indicate that the experimental group used some behaviour characteristics they learnt during training, namely “working systematically” and “causal relationship”. Thus, the study shows that favourable behaviour was learnt in the microworld, and that behaviour was subsequently used in the command-and-control training facility.     

Second order shear lag theory

The standard shear lag theory for elastic aligned short-fibre composites is extended to allow for a gradient of overall strain. The result is a one-dimensional strain gradient theory of the Toupin–Mindlin type. All parameters are the same as in the standard theory, and in the limits of weak strain gradients, large fibre aspect ratios or low elastic modulus ratios, the standard theory is recovered. The gradient effect is illustrated by a simple one-dimensional boundary value problem: a vertical composite rod fixed at both ends and loaded by gravity. The fibre length significantly affects the solution when the fibres are rigid and their length is near the rod length; but otherwise the effect is weak.     

Numerical Simulations of Lubricating Grease Flow in a Rectangular Channel with and without Restrictions

This article presents numerical simulations of the laminar flow of lubricating greases in a channel with rectangular cross section. Three greases with different consistencies (NLGI grades 00, 1, and 2) have been considered in three different configurations composed of a rectangular channel without restrictions, one rectangular step restriction, and one double-lip restriction. The driving pressure drop over the channel spans from 30 to 250 kPa. The grease rheology is described by the Herschel-Bulkley rheology model, and both the numerical code and rheology model have been validated with analytical solutions and flow measurements using micro-particle image velocimetry.     

PEPT study of particle cycle and residence time distributions in a Wurster fluid bed

Particle cycle and residence time distributions are critical factors in determining the coating quality in the Wurster process. Positron emission particle tracking experiments are performed to determine the cycle and residence times of particles in different regions of a Wurster fluid bed. The results show that particles tend to recirculate in and sneak out below from the Wurster tube. The experiments also show that a larger batch size leads to a shorter cycle time and a narrower cycle time distribution (CTD). It is possible to avoid recirculations and obtain a shorter cycle time and a narrower CTD by selecting the operating conditions appropriately or via equipment design. Experiments using binary mixtures of particles with a diameter ratio of 1.5 show that large particles have a longer cycle time than small particles and that the cycle time is shorter for mixtures with approximately equal amounts of small and large particles. © 2014 American Institute of Chemical Engineers AIChE J, 61: 756–768, 2015     

EU renewable energy support policy: Faith or facts?

The recent EU Commission proposal for promoting the supply of power from renewable energy sources was originally based on a pan-European, harmonised tradable green certificate (TGC) scheme. We suggest, on the basis of a multi-disciplinary analysis, that a pan-EU TGC system is not the way forward for Europe. It is vital that the Commission (and the majority of Member States) avoids implementation of such policy designs put forward by a coalition of vested interests. They should instead look at, and act upon, the available evidence from those countries that have experimented with TGCs (e.g. Flanders, UK and Sweden) and design policies that stand a better chance of meeting the criteria of effectiveness, efficiency and equity. In particular, the policies must enable EU to meet the immense innovation/industrialisation challenge by inducing the development of a capital goods industry that can, eventually, diffuse a broad range of technologies that use renewable energy sources. Only then we can acquire an ability to implement an industrial revolution in the energy system in a way that broadly meets the criteria of effectiveness and dynamic efficiency.