Spray dryer processed graphene oxide/reduced graphene oxide for high-performance supercapacitor

This study deals with the utility of mini spray dryer process to improve the dispersibility, of graphene oxide(GO) and its application for high-performance supercapacitor. Initially, the neutral solution of GO was obtained using the modified Hummer's method. After this, the prepared GO solution was processed by mini spray dryer to obtain a more purified, lighter, and dispersed form of GO which is named as spray dryer processed GO (SPGO). The SPGO thus obtained showed excellent dispersibility behavior with various solvents, which is not found in case of conventional oven drying. Furthermore, utility of SPGO and its reduced form (r-SPGO) for supercapacitor applications have been investigated. Results obtained from the cyclic voltammetry(CV) analysis, impedance, and charge-discharge behavior of supercapacitor fabricated using r-SPGO shows enhanced features. Therefore, the simple spray dried GO and its reduced form, that is, r-SPGO can be utilized as a potential candidate for the supercapacitor application. Herein, as synthesized SPGO exhibited the specific capacitance of 12.07 and 37.6 F/g with PVA-H₃PO₄ and 1 mol/L H₃PO₄, respectively, at a scan rate of 5 mV/s. On the other hand, reduced form of SPGO, that is, r-SPGO showed the specific capacitance of 27.16 and 230 F/g with PVA-H₃PO₄ and 1 mol/L H₃PO₄, respectively.     

Analysis and simulation of substrate coupling in integrated circuits

A technique is presented which allows efficient calculation of substrate-coupling macromodels in integrated circuits. the technique can be used to calculate node-to-node resistances or impedances in substrate models. Examples of the technique applied to several test structures are presented.     

Characterization of ZnS:Cu, Br electroluminescent phosphor prepared by new route

Synthesis of electroluminescent ZnS:Cu, Br phosphor by a number of routes has been presented along with their brightness-voltage, brightness-frequency, brightness-waveform and spectral energy distribution studies. The sample fired in N₂ atmosphere with aluminum and bromine shows predominantly green emission with a peak around 530 nm whereas the sample prepared under H₂S and HBr shows the broadest emission spectrum with multiple peaks. These peaks may arise out of different possible bands of copper, self-activated luminescence of ZnS and association of copper with some of the donor levels formed because of the higher reactivity of HBr. All the samples have been found to obey the relation B=B₀ exp.(−b/V^0.5) which has been discussed using bipolar tunnel emission model. The frequency variation of brightness is linear. Samples containing bromine show multiple secondary peaks indicating that bromine helps in formation of multiple shallow traps.     

Chitosan-based magnetic molecularly imprinted polymer: synthesis and application in selective recognition of tricyclazole from rice and water samples

A tricyclazole selective chitosan/Fe₃O₄ magnetic molecularly imprinted polymer (MMIP) was synthesized using non-covalent binding polymerization involving methacrylic acid (MAA) as functional monomer, divinylbenzene (DVB-80) as crosslinker, 2,2'-azobisisobutyronitrile as initiator, acetonitrile/toluene (75:25, v/v) as porogenic solvent and tricyclazole as template. Surface morphology and magnetic characterization of the prepared imprinted and non-imprinted polymers were done using scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectrometry and vibrating sample magnetometry, respectively. The adsorption kinetic data fitted best in pseudo-second-order model. The adsorption equilibrium was achieved in 30 min and the maximum binding capacity was 4579.9 µg/g. The Freundlich isotherm model was found suitable for explaining the binding isotherm data (R² > 0.99). Negative values of thermodynamic parameters ∆G (Gibb’s free energy), ∆H (enthalpy), and ∆S (entropy) revealed exothermic and spontaneous nature of adsorption processes. It also revealed decreased randomness at the solid–liquid interface during sorption. The scatchard plot analysis suggested heterogeneity of binding sites on MMIPs. The molecular recognition selectivity of MMIPs towards tricyclazole was much higher, as compared to its structural analogues, tebuconazole (α = 28.58) and hexaconazole (α = 37.16). The MMIPs were successfully applied to separate and enrich tricyclazole from fortified samples of rice and water, with a recovery percentage of 89.4% and 90.9%, respectively. These reusable imprinted polymers possessing high selectivity and specificity can be utilized as an adsorbent for solid-phase extraction in sample preparation for tricyclazole residue analysis in complex environmental matrices.

     

Morphology of EVA based nanocomposites under shear and extensional flow

Shear and extensional rheological measurements were conducted in conjunction with laser light scattering (LLS) on ethylene‐vinyl acetate copolymer (EVA) nanocomposites. The materials were prepared by melt‐mixing EVA and commercially acquired layered silicates. Wide Angle X‐Ray Scattering (WAXS) was used to ascertain the degree of layer swelling. This could be attributed to the intercalation of polymer chains into the interlayer of the silicates. The nanocomposites prepared were determined to be predominantly intercalated in nature. In shear rheological tests, the nanocomposites exhibited an increase in viscoelastic properties compared to the pure EVA. The extent of this property enhancement was not as pronounced as had been reported in many instances with respect to other polymer nanocomposites. This could be attributed to the absence of a network structure normally observed in an exfoliated system. The extensional rheological tests showed an increase in extensional flow properties. This was confirmed by the LLS, which indicated that the filled systems had higher deformability than the unfilled one. Polym. Eng. Sci. 44:1220–1230, 2004. © 2004 Society of Plastics Engineers.     

A novel approach to design optimal 2-D digital differentiator using vortex search optimization algorithm

Multimedia Tools and Applications - The designing of 2-D digital differentiator is multimodal and high dimensional problem which requires large number of differentiator coefficients to be...     

Melt processing of nanocomposites of cellulose nanocrystals with biobased thermoplastic polyurethane

Nanocomposites of thermoplastic polyurethane (TPU) with cellulose nanocrystals (CNC) without and with surface treatment are obtained by melt processing. Nanocomposites are obtained with nanofiller weight content near of the theoretical percolation threshold (3.9 wt%). Visual observation of CNC agglomerates is sufficient to prove the inefficiency of the mixing in systems with untreated CNC. The crystallization kinetics of the TPU changes with the addition of CNC and this is confirmed by differential scanning calorimetry analysis. Thermogravimetric analysis prove that the addition of CNC increases the thermal stability of the TPU. From the rheological analysis it is possible to verify the absence of percolation and an intermediate state of sol–gel transition in the nanocomposites. CNC/TPU nanocomposites with 5 wt% of treated CNC present better mechanical performance than de neat TPU and the other processed nanocomposites and display around 130% increase in Young's modulus while retaining significant values of toughness, tensile strength and elongation at break.     

Design and implementation of a block‐backstepping based tracking control for nonholonomic wheeled mobile robot

This paper presents formulation of a novel block‐backstepping based control algorithm to overcome the challenges posed by the tracking and the stabilization problem for a differential drive wheeled mobile robot (WMR). At first, a two‐dimensional output vector for the WMR has been defined in such a manner that it would decouple the two control inputs and, thereby, allow the designer to formulate the control laws for the two inputs one at a time. Actually, the decoupling has been carried out in a way to convert the system into block‐strict feedback form. Thereafter, block‐backstepping control algorithm has been utilized to derive the expressions of the control inputs for the WMR system. The proposed block‐backstepping technique has further been enriched by incorporating an integral action for enhancing the steady state performance of the overall system. Global asymptotic stability of the overall system has been analyzed using Lyapunov stability criteria. Finally, the proposed control algorithm has been implemented on a laboratory scale differential drive WMR to verify the effectiveness of the proposed control law in real‐time environment. Indeed, the proposed design approach is novel in the sense that it has judiciously exploited the nonholonomic constraint of the WMR to result in a reduced order block‐backstepping controller for the WMR, and thereby, it has eventually yielded a compact expression of the control law that is amenable to real‐time implementation. Copyright © 2015 John Wiley & Sons, Ltd.