Rapid determination of the membrane potential of mitochondria in small biopsy specimens of the liver

In liver transplantation, graft viability is ideally to be determined before implantation. Integrity of mitochondria may be a prerequisite to a viable graft. A new method is presented, which allows for the determination of the membrane potential of mitochondria (MPM; mV) in state 4 respiration within 50 min in 40-mg specimens, employing rhodamine 123 as a probe. Normal control showed a MPM of 239.2 mV. Storage in saline at 37 degrees C yielded an impaired MPM of 153.5 mV within 3 h. The cold storage at 1 degree C could preserve MPM at quasi-normal after 3 h but reduced it significantly after 24 h to 222.2 mV in saline (p < 0.005 vs. control) and 231.0 mV in UW solution (p < 0.05 vs. control): the difference between the 24-hour values was significant (p < 0.05).     

Relationships between hydrogen donor abilities and chemical structure of aromatic compounds in terms of coal liquefaction

To obtain fundamental information about hydrogen transfer, the relationships between hydrogen donor ability and chemical structure of model compounds representing donor solvents is studied using gas chromatography,¹H n.m.r. and computing calculation methods. The order of the model compounds in terms of the ability as donor solvent to release hydrogen is: decalin < tetralin < 1,2-dihydronaphthalene < < 1,4-dihydronaphthalene. This trend closely correlates with the difference in binding energies of the hydroaromatic compounds and their radicals, determined by intermediate neglect of differential overlap (INDO) calculation. Electron spin resonance spectroscopy (e.s.r.) confirms that radical species are created after heat-treatment of the donor compounds. The ability of model compounds representing coal to accept hydrogen is assessed from a comparison of the¹H n.m.r. spectra. It is established that donor and acceptor efficacies are dependent upon chemical structure.     

Colorimetric microdetermination of sulphites in foods by use of the modified rankine apparatus. IV.

Summary Detection and determination of traces of sulphites in foods was attempted by use of the modified Rankine apparatus and pararosaniline colorimetry. Replacement of alkaline titration reported previously by pararosaniline colorimetry lowered the absolute detection limit from 30 g (titration method) to 2 g. In view of clean analysis, in the color developing system, 0.1 N-sodium hydroxide was used in place of mercuric chloride solution commonly used as an absorbant of sulphites. In order to prevent oxidative decomposition of sulphites during operation, nitrogen gas was used as carrier instead of air. Dimedone and sodium azide were used for the elimination of aldehydes and nitrites, respecitvely, in the sample, which will disturb the color development of sulphites with pararosaniline-formaldehyde reagents. With this improved method, it was possible to determine the residual sulphites in frozen peeled shrimps, sugared beans and other foods with low sulphite contents accurately.

---

Colorimetrische Mikrobestimmung von Sulfiten in Lebensmitteln bei Anwendung der modifizierten IV. Rankine Apparatur

Zusammenfassung Geringe Sulfitmengen in Lebensmitteln (geschälte Garnelen, gezuckerte Bohnen) können colorimetrisch bestimmt werden. Die neuentwickelte Methode beruht auf einer Kombination von colorimetrischer Bestimmung mittels p-Rosanilin und der Bestimmungsmethode nach Rankine. Auf diese Weise lassen sich Gehalte von 2 g noch genau bestimmen. Bei der Farbentwicklung wurde das giftige Quecksilbertetrachlorid durch 0.1 n-NaOH ersetzt, anstelle von Luft Stickstoff als Trägergas verwendet und somit eine Oxydation des Sulfits während der Bestimmung vermieden. Da Nitrit und Aldehyde die Farbentwicklung stören, wurde ihr Einfluß durch Dimedon und Natriumazid ausgeschaltet.

---

---

Studies on the Analyses of Sulphites in Foods (IV)     

Optimization of equipment capacity and an operational method based on cost analysis of a fuel cell microgrid

A microgrid requires a stable supply of electric power and heat, which is achieved by the cooperative operation of two or more pieces of equipment. The equipment capacity and the operational method of the equipment were optimized using a newly developed orthogonal array-GA (genetic algorithm) hybrid method for an independent microgrid accompanied by a fuel cell cascade system, solar water electrolysis, battery, and heat storage. This type of system had not been hardly developed until now. The objective function of the proposed system was the minimization of the total amount of equipment and fuel cost over ten years. For the first step in the proposed analysis method, the capacity of each piece of equipment and the operational method, which are considered to be close to the optimal solution of the system, are combined using the orthogonal array and factorial-effect chart, which are an experimental design technique. In the next step, the combination described above provides the initial values to the GA, and the GA searches for the optimal capacity and operational method for each piece of equipment in question. Compared with a simple GA, the convergence characteristic improves greatly using the proposed analysis method developed in this study.     

An Investigation of Capacitors for Flying Capacitor Converters

Multilevel converters can essentially reduce harmonics even when their switching frequency is low. Among the various topologies of the multilevel converters, flying capacitor converters are considered to be promising converters for realizing high power density. However, the main circuit of the flying capacitor converters has many capacitors. Therefore, in this study, the volume of the capacitors in the flying capacitor converters is determined by taking into consideration the allowable ripple voltage and temperature rise in the capacitor. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 186(4): 81–91, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22361     

Analysis of a fuel cell micro-grid with a small-scale wind turbine generator

If electric power is supplied using an independent micro-grid connected to renewable energy, it can flexibly match the energy demand characteristics of a local area. And an independent micro-grid is expected to be effective in cutting greenhouse gas discharge and energy costs, as well as in eliminating the need for an emergency power supply system. Since the output of renewable energy is unstable, other energy equipment needs to cover the stability of output. Thus, the operating conditions of an independent micro-grid that supplies power with natural power sources and fuel cells are investigated. The operation conditions of a fuel-cell independent micro-grid with wind power generation were investigated by numerical analysis. Step loads and an apartment house power load model were analyzed using the dynamic characteristics of a fuel cell obtained from experiments. The output of wind power generation and fuel cells is controlled by proportional-integral control of an independent micro-grid for rapid power demand change.     

Economic efficiency of a renewable energy independent microgrid with energy storage by a sodium–sulfur battery or organic chemical hydride

The present study uses numerical analysis to investigate the operating methods and costs of an independent microgrid incorporating a sodium–sulfur (NAS) battery or an energy storage system using organic hydrides. Details relating to the operation of the system and its installed capacity and cost were clarified, assuming the introduction of an independent microgrid in Kitami City, a cold region in Japan. Analysis results indicate that energy storage technology using the organic hydride system is economically inferior to the NAS battery owing to large losses associated with the water electrolyzer and dehydration reactor. Therefore, for the widespread use of the organic hydride system, it is necessary to improve the efficiency of these components.     

Effects of Sampling Tube Geometry on Soft Clayey Sample Quality Evaluated by Nondestructive Methods

Sample disturbance caused by difference in sampling tube geometry was evaluated by two nondestructive methods: the measurement of the residual effective stress (p_r') by ceramic disc; and the use of the bender element to ascertain the shear wave velocity (V_s), and thus the maximum shear modulus (G_BE). Samples were measured under atmosphere, i.e., not under confined stress conditions. The soil samples were obtained from two sources: reconstituted Kasaoka clay prepared in the laboratory, and at the test site at Takuhoku, Hokkaido, Japan. Samplers with different geometrical designs, referring to the Japanese standard stationary piston sampler, were used for the model ground and field sampling. The geometrical effects of the sampling tube, for example, the thickness of the tube wall, the edge angle, and the existence of a piston were carefully examined. The quality of the samples taken with different samplers was evaluated by p_r' and G_BE, values which were normalized by the in situ vertical effective stress (σ'_vo) and G_f measured by the seismic cone test in the field. It was found from these studies that p_r'/σ'_vo and G_BE/G_f vary considerably due to the geometry of the sampler, with the edge angle of sampling tubes being the most important feature in obtaining high quality samples. The wall thickness, and thus, the area ratio of the sampler is not critical to the sample quality if the edge angle is sharp enough. The existence of the piston does not significantly influence the sample quality in field samples. Furthermore, the correlation between G_BE and p_r' was also investigated, and it was found that the two parameters are strongly dependent.     

Efficiency analysis of a combined PEFC and bioethanol‐solar‐reforming system for individual houses

In this research, the development of a bioethanol reforming system for fuel cells (FBSR: fuel cell with bioethanol steam reforming) using sunlight as a heat source was investigated. The system was investigated using the experimental result of catalyst performance, and numerical analysis. If ethanol purity is high, the production method of the bioethanol used for the proposal system will not be limited. The overall efficiency of the production of electricity and heat power of this system was determined by examining its thermal output characteristic. The FBSR was introduced into standard individual houses in Sapporo, Japan, for analysis. The amount of hydrogen production, the production‐of‐electricity characteristic, and the thermal output characteristic were examined using meteorological data on representative days in March and August. Compared with the representative day in March (28.0 MJ day⁻¹), the solar radiation of the representative day in August (37.0 MJ day⁻¹) is large. However, the amount of solar radiation fluctuation of the representative day in August in this analysis is large compared with the representative day in March. It depends for the overall efficiency of the system on the amount of solar radiation fluctuation rather than the amount of solar radiation. As a result, the overall efficiency of the system, defined as the rate of power and heat output compared with the amount of solar heat collected, was calculated to be 47.4 and 41.9% on the representative days in March and August, respectively. Copyright © 2009 John Wiley & Sons, Ltd.