Analysis of course errors on CVOR antennas (including effects ofmutual coupling between elements)

A VHF omnidirectional radio range (VOR) is a navigation aid radio beacon facility, which provides aircraft with azimuth information relative to the VOR station in question as the origin. In Japan, two types of VOR-the conventional type (referred to as a CVOR) and the Doppler type (referred to as a DVOR)-are currently in use. An element known as the Alford loop antenna (ALA), which changes the loading reactance, is used for the VOR because the horizontally polarized wave and nondirectivity in the horizontal plane are preferred. A VOR antenna consists of a carrier antenna and a sideband antenna-an aircraft receives separate signals from these two antennas and compares them to obtain azimuth information. The mutual coupling between the elements forming the carrier and the sideband antenna affects the directivity of the single elements, resulting in errors in azimuth information. With the mutual coupling between the antenna elements being taken into consideration, a quantitative calculation was made by using the moment method-the results of the calculation made it clear that a loading reactance value of -320 Ω is better to make not mutually coupled elements nondirectional while a loading reactance value of -600 Ω is optimum to minimize the azimuth error of a CVOR     

Scanning electron microscopy of the myosin-coated surface of polystyrene beads in a force-movement assay system for ATP-dependent actin-myosin sliding

An outbreak of Cryptosporidiosis occurred over three months in a British Columbia community, peaking in December 1990. Results of the case-control study and illness surveys support the hypothesis that transmission occurred in a public children's pool at the local recreation centre. Analysis using lab-confirmed cases revealed a matched odds ratio of 4.5 [95% CI 0.97, 20.83], and using clinical cases an unmatched odds ratio of 12.8 [95% CI 3.68, 46.77], associated with swimming in the children's pool within two weeks prior to onset of illness. Other risk factors were not significant. Attack rates in various groups of children's pool users ranged from 8% to 78%. The children's pool was closed for steam cleaning and disinfection. Unusually frequent defecations including liquid stools had occurred before and during the outbreak. Improvements were instituted for removal of feces and superchlorination of pool water.     

Flashover voltage characteristics of contaminated station insulators under temporary ac overvoltages in the ac system connected with a frequency converter station

According to the recent analysis results of temporary ac overvoltage in the ac system connected with a frequency converter station, large-magnitude over-voltages were confirmed to occur under some special system conditions. Most of the station insulators currently used cannot withstand such overvoltages according to an evaluation based on the data obtained earlier. The necessity of tests to be done to evaluate such performance more accurately was recognized. Both power frequency and switching impulse overvoltage flashover tests were made on contaminated insulators by the method well simulating the natural wetting condition. Switching impulse flashover voltage with the waveshape having a long wavefront time of 2 ms can be well correlated with the flashover voltage characteristics of temporary ac overvoltage. Higher flashover voltage characteristics were obtained by a clean fog test method compared with those obtained by equivalent fog test method.     

Radiative ignition mechanism of solid fuels

Transmittance of external radiation from a CO₂ laser through a boundary layer of decomposition products over a vertical sample surface is measured during the ignition period. The results indicate that there is significant absorption of the external radiation for PMMA, and a lesser but still not negligible amount, for red oak. An increase in gas phase temperature over surface temperature is observed over much of the ignition interval. Using the experimentally measured incident flux at the sample surface, surface temperature history was calculated from a model that included re-radiation and convection losses from the surface, endothermic decomposition and conduction into the material. The results confirm the significant effect of gas phase absorption on surface temperature. Steady-state-derived surface regression rate expression was used for PMMA in this model. The results raise questions about the validity of such data for the dynamic heating conditions during the ignition period. Further studies needed to understand the radiative ignition mechanism are identified.     

Ru-catalyzed anode materials for direct hydrocarbon SOFCs

A solid oxide fuel cell using a thin ceria-based electrolyte film with a Ru-catalyzed anode was directly operated on hydrocarbons, including methane, ethane, and propane, at 600 °C. The role of the Ru catalyst in the anode reaction was to promote the reforming reaction of the unreacted hydrocarbons by the produced steam and CO₂, which avoided interference from steam and CO₂ in the gas-phase diffusion of the fuels. The resulting peak power density reached 750 mW cm⁻² with dry methane, which was comparable to the peak power density of 769 mW cm⁻² with wet (2.9 vol.% H₂O) hydrogen. More important was the fact that the cell performance was maintained at a high level regardless of the change in the methane utilization from 12 to 46% but was significantly reduced by increasing the hydrogen utilization from 13 to 42%. While the anodic reaction of hydrogen was controlled by the slow gas diffusion, the anodic reaction of methane was not subject to the onset of such a gas-diffusion process.     

Effect of chromium content on remarkably rapid nitriding in austenitic Fe-Ni-Cr alloys

Remarkably rapid nitriding which is independent of diffusion theory based on the thermal activation process, was observed during nitriding of austenitic Fe-Ni-Cr steels containing 16 and 19 mass% chromium. Increase of the chromium content in the alloys yielded increasing thickness of the nitrided layer, i.e. the internal nitriding theory did not hold in the nitriding. No rapid nitriding was observed in steels containing less than 13 mass% chromium. Hence the limiting concentration of chromium for the rapid nitriding will lie between 13 and 16 mass% chromium. A solution to the problem of abnormalities arising during nitriding of practical austenitic stainless steels which have been investigated since 1972, has been presented experimentally by nitriding various chromium-containing steels. Based on the experimental results, the origin of the rapid nitriding is discussed in connection with the free-energy function of Cr₂N and CrN to temperature. In particular, a plateau of nitrogen concentration measured in the nitrided layers leads to the conclusion that a forced nitrogen diffusion in the layer resulted in the rapid nitriding.     

Solid-Phase Syntheses of Two Deacetyl-Thymosin β4 Analogues with Substitution at Position 12 and Their Effects on Impaired Blastogenic Response of T Lymphocytes of Uremic Patients

Two deacetyl-thymosin β₄ analogues containing Phe(4Br) or D-Phe(4Br) as position 12 were synthesized by the manual solid-phase method, and their immunological effects on the impaired blastogenic response of phytohemagglutinin-stimulated T lymphocytes of uremic patients with infectious diseases were studied. Bromination of the p-position of Phe¹² resulted in a marked restorative effect on the impaired blastogenic response of T lympocytes compared with that of our synthetic deacetyl-thymosin β₄ The synthetic [Phe(4Br)¹²]deacetyl-thymsin β₄ was approximately equal in potency to our synthetic [Phe(4F)¹²]deacetyl-thymosin β₄ in uremic patients, but the other analogue, [D-Phe(4Br)¹²]deacetyl-thymosin β₄, had no effect.     

Effects of nondensifying inclusions on the densification and microstructure of zinc oxide matrix composites

The densification and microstructure development of ZnO containing Zn₇Sb₂O₁₂, ZrO₂, and aggregated ZnO were investigated to elucidate the effect of nondensifying inclusions on the sintering of ceramic/ceramic composites. The inclusion retarded the densification, and the degree of retardation was found to depend on the chemical species of inclusion; Zn₇Sb₂O₁₂ had the largest effect, followed by ZrO₂ and then aggregated ZnO last. The experimental results for aggregated ZnO was explained by the theory which predicts the generation of backstresses. The backstresses give a less significant effect on the densification. For Zn₇Sb₂O₁₂ and ZrO₂, the microstructure of the matrix varied with distance from an inclusion particle; much porosity was observed in the region surrounding the inclusion. Circumferential voids, which are responsible for the suppression of densification, form during the initial stage of sintering. Inclusion particles generate an anchoring effect which retards the densification of the matrix immediately surrounding the inclusion particle during the intermediate stage.Supported by the Inamori Foundation.