Benchmark experiment of large-angle scattering reaction cross section of iron at 14 MeV using two shadow bars – Comparison of experimental results with ENDF/B-VIII –

ABSTRACT

It is important to perform neutron transport simulations with accurate nuclear data in the neutronics design of a fusion reactor. However, absolute values of large-angle scattering cross sections vary among nuclear data libraries even for well-examined nuclide of iron. Benchmark experiments focusing on large-angle scattering cross sections were thus performed to confirm the correctness of nuclear data libraries. The series benchmark experiments were performed at a DT neutron source facility, OKTAVIAN of Osaka University, Japan, by the unique experimental system established by the authors’ group, which can extract only the contribution of large-angle scattering reactions. This system consists of two shadow bars, target plate (iron), and neutron detector (niobium). Two types of shadow bars were used and four irradiations were conducted for one experiment, so that contribution of room-return neutrons was effectively removed and only large-angle scattering neutrons were extracted from the measured four Nb reaction rates. The obtained experimental results were compared with calculations for five nuclear data libraries including JENDL-4.0, JEFF.-3.3, FENDL-3.1, ENDF/B- VII, and recently released ENDF/B-VIII. It was found from the comparison that ENDF/B-VIII showed the best result, though ENDF/B-VII showed overestimation and others are in large underestimation at 14 MeV.     

An expert system for XPLE cable deterioration diagnosis and life forecasting

The recent increase in the demand for power in urban areas has caused changes in the way power is supplied. Underground distribution systems have been introduced for convenience in urban areas and to prevent injuries in case of a crisis. As a result, many new types of power cables are being used. One type, XPLE cables (also called CV cables) have been rapidly taking the place of conventional cables such as OF or SL cables since the 1960s because of their relatively easy installation and maintainability. However, distribution cables used under severe environmental conditions deteriorate rapidly (due mainly to water treeing), and some cables experience insulation breakdown. Therefore, many diagnostic methods have been developed, though they have not been very effective. By combining methods, a high reliability can be achieved in comparison to the use of a single method. However, processing the data is difficult for on-site personnel, so many experts are required. But there is a lack of qualified experts, hence we have turned to the development of expert systems.     

Thermal Shock Behavior of Porous Silicon Carbide Ceramics

Using the water-quenching technique, the thermal shock behavior of porous silicon carbide (SiC) ceramics was evaluated as a function of quenching temperature, quenching cycles, and specimen thickness. It is shown that the residual strength of the quenched specimens decreases gradually with increases in the quenching temperature and specimen thickness. Moreover, it was found that the fracture strength of the quenched specimens was not affected by the increase of quenching cycles. This suggests a potential advantage of porous SiC ceramics for cyclic thermal-shock applications.     

Preparation of heterotactic-rich poly(methyl methacrylate) with narrow molecular weight distribution bytert-butyllithium/bis(2,6-di-tert-butylphenoxy)methylaluminum

Summary Polymerization of methyl methacrylate (MMA) withtert-butyllithium (t-C₄H₉Li) in toluene in the presence of aluminum alkoxides such as ethoxide,tert-butoxide and 2,6-di-tert-butylphenoxide, were examined at various Al/Li ratios. In the cases of ethoxide andtert-butoxide, predominantly isotactic polymers with broad molecular weight distribution were obtained. Combinations oft-C₄H₉Li and bis(2,6-ditert-butylphenoxy)methylaluminum [MeAl(ODBP)₂] were found to be an efficient initiating system for heterotactic polymerization of MMA, which gives PMMA rich in heterotactic triads up to 68% with narrow molecular weight distribution (Mw/Mn=1.09–1.17). End group analysis by¹H NMR indicated thatt-C₄H₉Li initiates the polymerization and MeAl(ODBP)₂ works as a stereospecific modifier. From stereosequence analysis of the heterotactic PMMA by¹³C NMR, it was found that the calculated pentad fractions from the first-order Markovian statistics (Pm/r=0.742, Pr/m=0.627) fitted the observed ones better than those from Bernoullian statistics. The glass transition temperature of the heterotactic PMMA was 13°C lower than that of syndiotactic PMMA, and the intrinsic viscosity in tetrahydrofuran was close to that of isotactic PMMA with a similar molecular weight but higher than that of syndiotactic PMMA.     

Fracture Energies of Tape-Cast Silicon Nitride with β-Si3N4 Seed Addition

The fracture energies of the tape-cast silicon nitride with and without 3 wt% rod-like β-Si₃N₄ seed addition were investigated by a chevron-notched-beam technique. The material was doped with Lu₂O₃–SiO₂ as sintering additives for giving rigid grain boundaries and good heat resistance. The seeded and tape-cast silicon nitride has anisotropic microstructure, where the fibrous grains grown from seeds were preferentially aligned parallel to the casting direction. When a stress was applied parallel to the fibrous grain alignment direction, the strength measured at 1500°C was 738 MPa, which was almost the same as room temperature strength 739 MPa. The fracture energy of the tape-cast Si₃N₄ without seed addition was 109 and 454 J/m² at room temperature and 1500°C, respectively. On the contrary, the fracture energy of the seeded and tape-cast Si₃N₄ was 301 and 781 J/m² at room temperature and 1500°C, respectively, when a stress was applied parallel to the fibrous gain alignment. The large fracture energies were attributable primarily to the unidirectional alignment fibrous Si₃N₄ grains.     

Enhanced thermal stability of poly(lactide)s in the melt by enantiomeric polymer blending

Poly(l-lactide) (i.e. poly(l-lactic acid) (PLLA)) and poly(d-lactide) (i.e. poly(d-lactic acid) (PDLA)) and their equimolar enantiomeric blend (PLLA/PDLA) films were prepared and the effects of enantiomeric polymer blending on the thermal stability and degradation of the films were investigated isothermally and non-isothermally under nitrogen gas using thermogravimetry (TG). The enantiomeric polymer blending was found to successfully enhance the thermal stability of the PLLA/PDLA film compared with those of the pure PLLA and PDLA films. The activation energies for thermal degradation (ΔE_td) were evaluated at different weight loss values from TG data using the procedure recommended by MacCallum et al. The ΔE_td values of the PLLA/PDLA, PLLA, and PDLA films were in the range of 205-297, 77-132, and 155-242 kJ mol⁻¹ when they were evaluated at weight loss values of 25-90% and the ΔE_td value of the PLLA/PDLA film was higher by 82-110 kJ mol⁻¹ than the averaged ΔE_td value of the PLLA and PDLA films. The mechanism for the enhanced thermal stability of the PLLA/PDLA film is discussed.     

Effect of Agglomeration on Mechanical Properties of Porous Zirconia Fabricated by Partial Sintering

Porous ZrO₂ ceramics were fabricated by compacting a fine ZrO₂ powder, followed by pressureless sintering. Two unidirectional pressures of 30 and 75 MPa were used to prepare the green compacts. The strength and the fracture toughness of porous ZrO₂ specimens sintered from the compacts prepared by 75 MPa were substantially higher than those by 30 MPa, especially for the specimens with low porosity. However, the corresponding Young's moduli were identical. This caused the strain to failure of these porous bodies to increase significantly with increasing compaction pressure. Microstructural analyses showed that a number of voids and small flaws existed in the green compacts prepared by the lower pressure, due to the agglomeration of fine ZrO₂ grains. It was revealed that the ZrO₂ agglomeration resulted in a localized nonuniform shrinkage and degraded the mechanical properties of porous ZrO₂ ceramics.     

Uniformly Porous Composites with 3-D Network Structure (UPC-3D) for High-Temperature Filter Applications

Uniformly porous composites with 3-D network structure (UPC-3D) have been recently developed via a pyrolytic reactive sintering process, which takes advantage of the evolved CO₂ gas from a decomposing carbonate source (e.g., dolomite, CaMg(CO₃)₂) and does not require any additional pore-forming agent nor long-time burning-out process. Through liquid formation via LiF doping, strong necks are formed between constituent particles before completion of the pyrolysis of carbonate, resulting in the formation of a strong 3-D network structure. The pore size distribution is very narrow (with typical pore size: ∼1 μm), and the porosity was controllable (∼30–60%) by changing the sintering temperature. This article presents the development details of UPC-3D, and reports the recent findings in CaZrO₃/MgAl₂O₄ system, which will be one of the more promising systems for practical applications.     

Microstructures of functionally graded materials fabricated by centrifugal solid-particle andin-situ methods

Functionally graded materials (FGMs) belong to a relatively new class of inhomogeneous composite materials, in which the composition and/or microstructure undergo a gradual change along some directions. In this review article, the microstructures and composition gradients in Al/SiC, Al/Shirasu (volcanic eruptions commonly found in south Kyushu in Japan), Al/Al₃Ti, Al/Al₃Ni, Al/Al₂Cu FGMs have been investigated. The Al/SiC, Al/Shirasu and Al/Al₃Ti FGMs are fabricated by the centrifugal solid particle method where the distribution particles of SiC, Shirasu and Al₃Ti are solids in the melts. On the other hand, Al/Al₃Ni and Al/Al₂Cu FGMs are fabricated by the centrifugalin-situ method where Al/Al₃Ni and Al/Al₂Cu systems have lower liquidus temperatures than the processing temperatures. The feature of Al/(Al₃Ti−Al₃Ni) hydrid FGM, which is fabricated by a method combining both the centrifugal solid-particle andin-situ methods, is also shown.     

Role of electron-phonon interaction in lattice dynamics and superconductivity of oxide spinel LiTi2O4

The lattice dynamics of an oxide spinel LiTi₂O₄ is studied by taking account of the electron-phonon (EP) interaction derived on the basis of the realistic tight-binding bands fitted to the first-principles bands. Due to the characteristic dependences of the EP interaction on wavevectors and vibrational modes, a remarkable frequency renormalization of the O vibrational modes, which hybridize with the Ti vibrational modes, is obtained over a wide region of the Brillouin zone. The overall features of the calculated phonon density of states are in agreement with those observed by the inelastic neutron scattering measurements. By using the EP interaction and the renormalized phonon frequencies we have calculated the EP spectral function ² F(). The superconducting transition temperature, gap function, and tunneling spectra are calculated by solving the Éliashberg equation. The results agree well with the observations.