Synergistic Effects of Polybenzimidazole and Aramide on Enhancing Flame-Retardancy and Solubility

Aromatic and functional polymers with processibility derived from biobased starting materials are prerequisite considering sustainable society. Poly(2,5-benzimidazole)s are rigid-rod polymers to show ultrahigh thermal stability such as flame retardance, while usually suffer from poor solubility. Here, poly(benzimidazole-co-amide)s are synthesized from two biobased monomers, 3,4-diaminobenzoic acid and a semirigid comonomer, 4-aminohydrocinnamic acid. The copolymers with an amide composition of 80 mol% and higher are soluble in widely used polar solvents to fabricate the films keeping high flame retardance, which is comparable with popular high-performance polymers such as aromatic polyimides, polyetheretherketone, polyphenylene sulfide, etc.     

Evaluation of inelastic constitutive models under plasticity-creep interaction for steel at 600°C

Uniaxial tests to identify plasticity-creep interaction in steel at 600°C were carried out as the Benchmark Project by the Subcommittee on Inelastic Analysis and Life Prediction, JSMS. The purpose of this paper is to present recent experimental data and predictions of constitutive models obtained in the project. Ten types of constitutive models were utilized to compare analytical predictions to sixteen benchmark experiments which are grouped into four categories: (I) tensile and creep tests under monotonic loading, (II) mixed mode tests under plastic and creep loading, (III) ratcheting deformation tests under program loads, and (IV) cyclic deformation tests under the combination of different strain rates. The benchmark tests in Group IV are used to estimate the creep-fatigue life of steel; the results will be published in a separate paper.     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

Novel hepatitis C virus protease inhibitors: thiazolidine derivatives

This study evaluated the inhibitory effects of thiazolidine derivatives on hepatitis C virus (HCV) protease and other human serine proteases. The inhibition efficacy was tested with a reversed-phase high-performance liquid chromatography (HPLC) assay system using a NS3-NS4A fusion protein as the HCV protease and a synthetic peptide substrate that mimics the NS5A-5B junction. Nine thiazolidine derivatives showed more than 50% inhibition at 50 microg/ml. The most potent derivative was RD4-6250, with 50% inhibition at a concentration of 2.3 microg/ml; this concentration was lower than those of other protease inhibitors reported previously. The most selective derivative was RD4-6205, with 50% inhibition at a concentration of 6.4 microg/ml, a lower concentration than those on other serine proteases (chymotrypsin, trypsin, plasmin, and elastase). These results suggest that the RD4-6205 skeleton is an important structure for inhibitory activity on the HCV protease NS3-NS4A.     

Optical and electronic properties of cobalt-doped zinc oxide films prepared by the sputtering method

In-doped ZnO, Co-doped ZnO and Li-doped NiO are successively deposited on quartz by the sputtering method. A current versus voltage curve of the three-layer device, in which the Indoped ZnO and Li-doped NiO are used as electrodes, reveals that the In-doped ZnO is an ohmic electrode and the Li-doped NiO is a blocking electrode with respect to electron injection. In photocurrent spectra of the three-layer device, there are two distinct peaks around 410 and 640 nm. The former is ascribed to the photoionization caused by the electric-dipole transition from the ground states,⁴A₂(F), to the conduction band, and the latter to the thermal emission from electronic excited states of Co²⁺,⁴T₁(P).     

Construction of a control system for disturbance rejection using a dual observer

A well‐known control system which can reduce the adverse effects of disturbances is a disturbance observer. However, in many cases of mechanical systems, system disturbances which do not satisfy the matching condition may be imposed. Therefore, it may be difficult to reduce the adverse effects of the disturbances by the traditional disturbance observer. In this paper, a method of control system synthesis for disturbance rejection using a dual observer is proposed. This method is based on the zeroing induced by the disturbance localization problem. This problem may be solved by dividing the state space into observable subspace and unobservable subspace. As compared with an H_∞ controller based on perfect observation, the usefulness of the proposed control system for disturbance rejection is demonstrated by numerical simulations for a two‐mass spring system. © 2002 Scripta Technica, Electr Eng Jpn, 138(4): 50–60, 2002; DOI 10.1002/eej.1138     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

Distributed architecture for energy management D-structure

Electric power systems are expanding in size and complexity, and the requirement for the energy management system (EMS) is becoming more important. In this computer control system, a single control computer is used mainly as the primary computer and its software is very complicated because of its hugh number of small, quick tasks to obtain high response speed. Therefore, much effort is needed to develop and modify the programs, and the responsiveness of this centralized architecture varies greatly when many faults occur in the power system. This paper describes a new distributed architecture for the EMS. Distributed processors execute the functions cooperatively with periodic access to the common bulletin board database in which information about the power system exist. This architecture facilitates the software development and maintenance, and it also enhances the performance by the parallel processing of the distributed functions.     

Gene expression in brain during cuprizone-induced demyelination and remyelination

When C57BL/6J mice, 8 weeks of age, received 0.2% Cuprizone in their diet, extensive demyelination in corpus callosum was detectable after 3 weeks, and there was massive demyelination by 4 weeks. As expected, the accumulation of phagocytically active microglia/macrophages correlated closely with demyelination. When Cuprizone was removed from the diet, remyelination was soon initiated; after 6 weeks of recovery, myelin levels were near-normal and phagocytic cells were no longer prominent. Steady-state levels of mRNA for myelin-associated glycoprotein, myelin basic protein, and ceramide galactosyltransferase were already profoundly depressed after 1 week of Cuprizone exposure and were only 10-20% of control values after 2 weeks. Unexpectedly, upregulation of mRNA for these myelin genes did not correlate with initiation of remyelination but rather with accumulation of microglia/macrophages. After 6 weeks of exposure to Cuprizone, mRNA levels were at control levels or higher-in the face of massive demyelination. This suggests that in addition to effecting myelin removal, microglia/macrophages may simultaneously push surviving oligodendroglia or their progenitors toward myelination.     

Sensitivity of an anadically oxidized aluminium film on a surface acoustic wave sensor to humidity

The sensitivity, transient response and sensitivity mechanism of a surface acoustic wave humidity sensor using porous anodically oxidized aluminium (alumina) films as mechanical interfaces have been studied theoretically and experimentally. It is found that the sensitivity of alumina films of 1.0 μm thickness is -0.034 m/(s %RH) and is the same order as that of polyimide films. The transient response of alumina films to humidity is about one order faster than that of polyimide films. For the sensitivity mechanism, the phase-velocity change is attributed to the mechanical perturbation caused by the absorption of water molecules. The equivalent density change of alumina films between 0 and 100%RH is about 0.7%. In addition, the actual stiffness constants of alumina films are two orders less than those of bulk alumina.