Polarity Effect and Electromagnetic Radiation of Partial Discharge Accompanying Growth of Electrical Tree

We have investigated the characteristics of radiated electromagnetic (EM) waves from positive and negative partial discharges (PD) in epoxy resin and cross‐linked polyethylene. We found that there is a correlation among the EM level from PD, the positive PD current, and electrical trees. Therefore, the growth of an electrical tree produces a lot of positive PD. We have also investigated the characteristics of the frequency region of EM waves from PD in air, insulating oil, and liquid epoxy in addition to the above insulators. EM waves were detected in the frequency region of 40 MHz to 300 MHz from positive and negative PD in epoxy resin and cross‐linked polyethylene. EM waves were also detected in the frequency region of 40 MHz to 150 MHz from positive and negative PD in air. In the case of insulating oil and liquid epoxy, EM waves were detected in the frequency regions of 40 MHz to 150 MHz from positive PD, and 40 MHz to 250 MHz from negative PD. The frequency region differed depending on the material and the discharge polarity. Our investigation indicates that the cause is differences in electric field strength at the time of PD occurrence.     

Glycoconjugated polymer 6. Synthesis of poly[styrene-<Emphasis Type="Italic">block</Emphasis>-(styrene-<Emphasis Type="Italic">graft</Emphasis>-amylose)] via potato phosphorylase-catalyzed polymerization

Summary The potato phosphorylase-catalyzed polymerization of α-D-glucose-1-phosphate (G-1-P) onto poly[styrene-block-(4-vinylbenzyl maltohexaoside)] (1) was performed at the molar ratios of [G-l-P]₀ and [maltohexaose]₀ of 35, 80, and 250. The product was found to be soluble in dimethyl sulfoxide, which was a good solvent for amylose, and showed the complex-formation with iodine, indicating that the product was assignable to poly[styrene-block-(styrene-graft-amylose)] (2). The quantitative analysis of the liberated phosphoric acid gave the average degree of polymerization o f the glucose unit (n) as 27, 5 1, and 180 for 2-I, 2-II, and 2-III, respectively. Received: 29 November 2002/Accepted: 22 December 2002 Correspondence to Toyoji Kakuchi     

Relation between encoder and syndrome former variables and symbol reliability estimation using a syndrome trellis

We derive a linear correspondence between the variables of an encoder and those of a corresponding syndrome former. Using the derived correspondence, we show that the log-likelihood ratio of an information bit conditioned on a received sequence can be equally calculated using the syndrome trellis. It is shown that the proposed method also applies to recursive systematic convolutional codes which are typical constituent codes for turbo codes. Moreover, we show that soft-in syndrome decoding considering a priori probabilities of information bits is possible in the same way as for Viterbi decoding based on the code trellis. Hence, the proposed method can be applied to iterative decoding such as turbo decoding. We also show that the proposed method is effective for high-rate codes by making use of trellis modification.     

Changes in the gaseous H2S barrier properties of damaged silicate coated nylon 6 films

The damage imposed on SiO _x deposited nylon 6 films as a result of abrasion with a cotton cloth and Gelboflex testing was examined by evaluating the rate at which copper plates, which were enveloped by the damaged films, were corroded by H₂S. Abrasion with a cotton cloth caused some micro-cracking of the SiO _x layer and the permeation rate of H₂S approached that of the uncoated nylon 6 film. Damage to the SiO _x layer by twisting and crushing progressed gradually with the number of Gelboflex test cycles and correspondingly the corrosion rate of the copper plates increased. Comparison of the corrosion rates of the copper plates kept in the pouches made of various commercial films with those obtained for the damaged SiO _x deposited nylon 6 films showed a clear relationship between the H₂ permeation rate of the films and the corrosion rate of the copper plates by H₂S.     

Recovery of fluorocarbons in Japan as a measure for abating global warming

The objective of this study is to evaluate the potential for recovering fluorocarbons as measures for the abatement of global warming. In this study, we focused on the three different kinds of fluorocarbons: CFCs, HCFCs and HFCs, and targeted refrigerant use because of the availability of relevant data. We first estimated future fluorocarbon emissions from the targeted appliances; we next compared those emissions in the units of CO₂ equivalent to the level of CO₂ emissions in 1990 from a quantitative point of view. As the result of this study, it was found that fluorocarbon emissions in 1999 and 2010 would be equal to approximately 7 and 3% of the level of CO₂ emissions in 1990 respectively. Moreover, if we implement a 100% recovery rate in every recovery route, we can reduce a large amount of emissions which correspond to approximately 2–5% of the level of CO₂ emissions in 1990, even if we take into account the energy-related CO₂ emissions by the transportation and decomposition of fluorocarbons.     

Temporal Specificity of Extinction in Autoshaping.

Three experiments investigated the effects of varying the conditioned stimulus (CS) duration between training and extinction. Ring doves (Streptopelia risoria) were autoshaped on a fixed CS-unconditioned stimulus (US) interval and extinguished with CS presentations that were longer, shorter, or the same as the training duration. During a subsequent test session, the training CS duration was reintroduced. Results suggest that the cessation of responding during an extinction session is controlled by generalization of excitation between the training and extinction CSs and by the number of nonreinforced CS presentations. Transfer of extinction to the training CS is controlled by the similarity between the extinction and training CSs. Extinction learning is temporally specific. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Survey of switching techniques in high-speed networks and their performance

One of the most promising approaches for high speed networks for integrated service applications is fast packet switching, or ATM (asynchronous transfer mode). ATM can be characterized by very high speed transmission links and simple, hard-wired protocols within a network. To match the transmission speed of the network links, and to minimize the overhead due to the processing of network protocols, the switching of cells is done in hardware switching fabrics in ATM networks. A number of designs have been proposed for implementing ATM switches. Although many differences exist among the proposals, the vast majority of them are based on self-routeing multistage interconnection networks. This is because of the desirable features of multi-stage interconnection networks such as self-routeing capability and suitability for VLSI implementation. Existing ATM switch architectures can be classified into two major classes: blocking switches, where blockings of cells may occur within a switch when more than one cell contends for the same internal link, and non-blocking switches, where no internal blocking occurs. A large number of techniques have also been proposed to improve the performance of blocking and non-blocking switches. In this paper, we present an extensive survey of the existing proposals for ATM switch architectures, focusing on their performance issues.     

Synthesis and surface properties of novel fluoroalkyl end-capped amphiphilic fullerene cooligomers

New fluoroalkyl end-capped fullerene cooligomers were prepared by the reactions of fluoroalkanoyl peroxides with fullerene and comonomers such as acryloylmorpholine, N,N-dimethylacrylamide and acrylic acid. These fluorinated fullerene cooligomers were easily soluble in water and common organic solvents, and were able to reduce the surface tensions of both water and benzene, quite effectively. Additionally, these fullerene cooligomers were found to form a stable monomolecular film at the air-water interface, and the modified polystyrene surface treated with these cooligomers was shown to have a strong hydrophilicity with good oil repellency.     

Surface Hardening of Carbon Steel Using High Powered YAG Laser

A high powered YAG laser with kaleidoscope for surface modification was applied to the surface hardening of carbon steels containing 0. 18-0.54 wt% C without the absorbents, and the relationships between laser processing and surface hardening were investigated by hardness and microstructure. The structure of the hardened zone underwent complete martensitic transformation in all of the carbon steels tested, and its hardness increased with greater carbon content. Under identical irradiated conditions, the hardened zone expanded with increasing carbon content. A hardened zone extending from the surface to a depth of 1.0 mm was obtained at a laser power of 1.0 kW and a scanning speed of 1 mm/sec. It was found that in the surface hardening of carbon steels, a high powered YAG laser can be used to control the hardened zone by selecting the appropriate irradiation conditions, however, the hardened zone was affected by the assistant gas and the flow rate.