Oxidation of doped europium in BaMgAl10O17 by annealing studied by x‐ray‐absorption fine‐structure measurements

Abstract— We studied the influence of annealing in air on doped europium in BaMgAl₁₀O₁₇ by performing x‐ray absorption fine‐structure measurements. We determined the oxidation of doped divalent europium by annealing in air at over 500°C. The interatomic distance between the europium and the surrounding oxygen atoms was compressed by oxidation. It also appears that the oxidation process of europium is determined by the diffusion of oxygen into BaMgAl₁₀O₁₇.     

Characterization of localized states in thin PrBa2Cu3O7−x tunnel barriers

Characteristic power-law dependence of junction conductance on temperature was confirmed at low temperatures fora,b-axis oriented Au/PrBa₂Cu₃O_7−x /YBa₂Cu₃O_7−y junctions with a PrBa₂Cu₃O_7−x layer thinner than 30 nm, indicating that current transport via a small number of localized states was predominant. The radius and the density of the localized states were estimated to be 1.1 nm and 5.0x10¹⁹ eV⁻¹ cm⁻³, respectively. Transport measurement at 1.7 K in a magnetic field of up to 6 T revealed no indication of on-site Coulomb repulsion of electrons in the localized states. These results support the possibility of resonant tunneling of Cooper pairs in superconductor-insulator-superconductor junctions with a thin PrBa₂Cu₃O_7−x tunnel barrier.     

A flow simulation for the epoxy casting process using a 3D finite‐element method

A three‐dimensional flow simulation for epoxy casting has been developed. A control‐volume‐based finite‐element method is employed, containing a conservative upwind formulation for the advection terms and equal order interpolations for all variables. This simulation predicts the non‐isothermal and reactive flow behavior under the gravity. The viscosity and reaction‐rate parameters were estimated by using a dynamic rheometer and a differential scanning calorimeter. The predicted flow front advancement and temperature profiles in the calculation domain similar to the mold cavity were in close agreement with the corresponding experimental results. The variation of epoxy surface configuration with flow rate also showed the same tendency between the prediction and the experiment. This simulation seems to be applicable not only to the epoxy casting, but also to other molding processes of various thermoset resins. POLYM. ENG. SCI. 45:364–374, 2005. © 2005 Society of Plastics Engineers.     

Right atrial contractile performance in patients with myocardial infarction

To evaluate right atrial (RA) contractile performance in patients with myocardial infarction, we validated a cineangiographic method of RA volume measurement, and investigated RA volume change in 'normal' individuals and patients with a previous myocardial infarction. Sixteen silicone rubber RA casts made from human cadavers were filmed in the postero-anterior and left lateral projections. The cast volumes calculated following Simpson's rule were in good agreement with those measured by water replacement (r = 0.992, P < 0.01). At cardiac catheterization, biplane RA cineangiography was performed in 19 'normal' individuals (N group), in 14 patients with a previous antero-septal infarction (AMI group) and in seven patients with a previous inferior infarction (IMI group). The RA volume-time curve was constructed at 20-40 ms intervals for one cardiac cycle. RA volume at the beginning of the atrial contraction (RAVd), which was defined as the 'preload' of the RA, tended to be larger in both the AMI and IMI groups compared with 'normal' individuals. The RA ejection volume was significantly larger in both the AMI (18.4 +/- 2.1 ml.m-2, P < 0.01) and IMI groups (19.4 +/- 2.8, P < 0.01) than in the N group (14.5 +/- 1.9), even for a comparable level of RAVd (range from 26 to 36 ml.m-2) (18.6 +/- 2.1, P < 0.01, 18.2 +/- 2.0, P < 0.01, 14.7 +/- 1.9, respectively). These results suggest that RA contraction increases in patients with myocardial infarction by increasing both the 'preload' and 'contractility' of the RA.     

Two geometrical isomers of linoleic acid: Improved total syntheses

The total syntheses of 9(Z),12(E)- and 9(E),12(Z)-octadecadienoic acids have been carried out. A useful intermediate in both syntheses, 8-bromo-octanoic acid, recently has become available from commercial sources. This compound has been used to expedite the preparation of these isomers. The remaining carbon atoms were derived from propargyl alcohol along with either 1-heptyne or acetylene and 1-bromopentane. Because the overall yield for each sequence was roughly 15% and there were no extraordinary reaction conditions in any of the synthetic steps, the compounds could be prepared readily in multiple gram quantities. The syntheses of the two compounds were supported by data from a variety of spectroscopic techniques.     

Forensic toxicological application of TOXI-LAB screening for biological specimens in autopsy cases and emergency cares

Using the TOXI-LAB drug detection system, emergency toxicological screening was performed in autopsy cases and emergency cares. In 280 autopsy cases (male 182 cases 65%, female 98 cases 35%), drug positive cases were 28 cases of male (15%) and 24 cases of female (24%). The age groups which showed higher rate of drug positive cases were 10s-40s in male (approximately 20%) and 20s in female (67%). In the 238 cases of emergency care (male 129 cases 54%, female 104 cases 44%, unknown 5 cases 2%), drugs were positive in 29 cases of male (22%) and 32 cases of female (30%). The age groups which showed relatively higher rate of drug positive cases were 40s in male (64%), 20s (71%) and 30s (89%) in female. Forty-four different kinds of drugs were detected in TOXI-LAB positive cases, in which the psychotropic drugs and the sedative-hypnotic drugs amounted to approximately 70%. Methamphetamine and amphetamine, which were the main abused drugs showing a socially important problem, were detected in total 15 cases. TOXI-LAB was based on thin-layer chromatography (TLC); however, from the extraction to development, coloration and detection have been accelerated (about 50 min) and simplified. In order to perform the forensic toxicological practice in Japan, it becomes more useful that TOXI-LAB is used in autopsy cases and emergency cares, if the drugs, which have caused poisoning cares in Japan, are added to TOXI-LAB. The present study describes the advantage and problem of TOXI-LAB drug detection system through demonstrating the practical cases of autopsy cases and emergency cares.     

Distribution of higher-order structures in injection-molded polypropylenes

Flexural test specimens were injection-molded from six homoisotactic polypropylenes with MFI = 0.49-25.1 dg/min under cylinder temperatures of 200-320°C. Distributions in the flow direction of higher-order structures such as crystallinity X_c, thickness of skin layer, a*-axis-oriented component fraction [A*], and crystalline orientation functions and distributions in the thickness direction of higher-order structures such as X_c, β-crystal contents, [A*], and crystalline orientation functions were studied. These higher-order structures are inhomogeneous in the flow and thickness directions, which strongly influences the product properties such as mechanical and thermal properties. Molecular orientation process in injection molding was theoretically analyzed from a viewpoint of growth of recoverable shear strain at the gate and its relaxation in the cavity, which could considerably well explain the variations in the flow and thickness directions of the quantities such as thickness of the skin layer and crystalline orientation functions which express the degree of molecular orientation.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

66/77-kV C-GIS using composite insulation in SF6 gas

A second-generation model of cubicletype gas-insulated switchgear (C-GIS) with composite insulation incorporating SF₆ gas has been developed. The design does not require a gas process in field assembly; it has high reliability and its installation is more rapid; and a further reduction in size is achieved. The design principles are described in detail.