Damage tolerance of glass mat/epoxy laminates hybridized with flexible resin under static and impact loading

This study deals with the impact property and damage tolerance of matrix hybrid composite laminates with different laminate constitution. The matrix hybrid composite laminates consisted of the laminae with a conventional epoxy resin and the laminae with a flexible epoxy resin modified from the conventional resin to avoid the interlaminar delamination. The impact energy absorption ratio greatly depended on the matrix resin placed at the impact face. The energy absorption was almost constant if the conventional resin was placed at the impact surface layer, while it increased exponentially with the increasing fraction of the flexible resin if the flexible resin was placed at the impact face. The impact energy was absorbed by the damage development and propagation in the laminate with conventional resin laminae as the impacted face, while it was absorbed by both the recoverable deformation of the flexible resin and the damage propagation in the laminate with flexible resin laminae as the impacted face.     

Quasi-optical waveguide-mode converters using a pair of phase correction mirrors

This paper describes a quasi-optical method for the conversion of modes transmitted through highly oversized circular waveguides. A waveguide-mode is radiated once from a waveguide cut in the form of a radiation beam, which is then properly shaped by two curved mirrors and directed back into the waveguide. The curved mirror shapes are iteratively and automatically determined for given propagation distances using the design technique for phase correction mirrors. The proposed method gives favorable results in designing a waveguide expander/reducer, a TE₀₁-TE₀₂ mode converter, and a TE₀₁-HE₁₁ mode converter.     

Effect of grain size on creep of Ti-53.4mol%Al intermetallics at 1100 K

Constant stress creep under compression stress, 100 to 316 MPa, at 1100 K was investigated on single-phase TiAl intermetallics. The material was ingot-cast, isothermally forged, and then annealed to produce stable equi-axed grain structures, whose average grain diameters were 25, 42 and 70m. Creep curves were very similar among the three specimens with different grain diameters and the creep rates at a given strain, as well as the minimum creep rates, depended little on grain size. Two regimes were observed on the stress dependence of the minimum creep rate. The stress exponent under high stresses was about 4.5, independent of grain size. Under stresses lower than about 150 MPa it became about 8.     

An Application of Silica‐Based Monolithic Membrane Emulsification Technique for Easy and Efficient Preparation of Uniformly Sized Polymer Particles

Summary: Uniformly sized polymer particles were prepared by an emulsification and polymerization technique utilizing a silica monolithic membrane, namely the “silica monolithic membrane emulsification technique”. In this paper, we utilized silica monolithic membrane as a device for the preparation of uniformly sized polymer particles. A mixture of monomers, diluents and oil‐soluble initiator was emulsified into a continuous medium through the silica monolithic membrane and polymerized. The particles obtained had a higher size uniformity than that of particles prepared by previously reported membrane emulsification techniques, such as the Shirasu Porous Glass (SPG) emulsification technique. Through the silica monolithic membrane emulsification technique, we could prepare particles having availability as a possible packing material for solid‐phase extraction (SPE) and high performance liquid chromatography (HPLC).

SEM photograph of silica particles prepared through capillary plate membrane.     

Differences between corrosion products formed on copper exposed in Tokyo in summer and winter

We analyzed the copper corrosion products that formed during a month in summer and a month in winter at three sites in Tokyo using several analytical techniques. The X-ray diffraction patterns revealed that cuprite Cu₂O and posnjakite Cu₄SO₄(OH)₆·H₂O formed on copper exposed in summer. By contrast, only cuprite was found in winter exposed copper. The X-ray fluorescence results indicated that the amounts of sulfur and chlorine on the copper plates exposed in summer were much greater than those in winter. This could be explained by the change in particulate sulfate and sea salt concentrations. Depth profiling analysis by Auger electron spectroscopy revealed that the oxide layer formed in summer was thicker than that in winter. This difference in oxide layer thickness could have been due to the differences in temperature, relative humidity, and the amount of sulfur and chlorine on the copper plate.     

Pressure-pulsed chemical vapour infiltration of TiN to SiC particulate preforms

SiC particulate preforms were infiltrated by TiN matrix from a gas mixture of TiCl₄ (5%), nitrogen (30%) and hydrogen using a repeating pressure pulse between 760 and about 1 torr. SiC particle sizes of 5 and 20 m were used. For matrix packing into deep level, optimum temperature was determined between 800 and 850 °C, and the maximum packing ratio reached 67% after 4 × 10⁴ pulses at 850 °C. The increase of TiCl⁴ concentration to 10% resulted in higher deposition rate and packing ratio. The decrease of nitrogen concentration led to slower deposition, that is, a similar effect to temperature lowering. The maximum flexural strength measured was 140 MPa.     

On the lower bounds of the second order nonlinearities of some Boolean functions

The rth order nonlinearity of a Boolean function is an important cryptographic criterion in analyzing the security of stream as well as block ciphers. It is also important in coding theory as it is related to the covering radius of the Reed-Muller code R(r,n). In this paper we deduce the lower bounds of the second order nonlinearities of the following two types of Boolean functions:

1.

with d=2^2r+2^r+1 and , where n=6r.

2.

, where x,y∈F_2^t,n=2t,n?6 and i is an integer such that 1?i<t,gcd(2^t-1,2ⁱ+1)=1.

For some λ, the functions of the first type are bent functions, whereas Boolean functions of the second type are all bent functions, i.e., they possess the maximum first order nonlinearity. It is demonstrated that in some cases our bounds are better than the previously obtained bounds.     

Characterization of a class III chitinase from Vitis vinifera cv. Koshu

A chitinase gene (Chi3K) was cloned from the genomic DNA of Vitis vinifera cv. Koshu. The structural gene comprised 891 by without introns and encoded 297 amino acids. The Chi3K product showed high similarity to the class III chitinase of V. vinifera cv. Pinot noir. Chi3K was expressed using a bacterial expression vector for purification and enzymatic characterization of its gene product. The recombinant chitinase exhibited hydrolytic activity toward glycol chitin and its optimum pH was 4.0. It also inhibited the growth of Botrytis cinerea, which causes grey mold disease in grapes.