Thermal stability of reinforced Nb3Sn composite superconductor under cryocooled conditions

Several types of reinforced Nb₃Sn wires have been developed to prevent reduction of superconducting properties by applying a strong electromagnetic force. To fabricate a cryocooled magnet using those reinforced wires, we experimentally measured the minimum quench energy (MQE) under cryocooled conditions of some reinforced Nb₃Sn wires. As a result, it became clear that thermal stability expressed as MQE was controlled by the temperature margin between the temperature of the operating condition and the transition temperature from superconductivity to normal. Using the FEM analysis, it was realized that the cause of the decline in thermal stability for the reinforced wires was the low thermal conductivity of the reinforced materials.     

Hematopoietic and lymphopoietic responses in human granulocyte-macrophage colony-stimulating factor (GM-CSF) receptor transgenic mice injected with human GM-CSF

Using a clonal assay of bone marrow (BM) cells from transgenic mice (Tg-mice) expressing the human granulocyte-macrophage colony-stimulating factor receptor (hGM-CSFR), we found in earlier studies that hGM-CSF alone supported the development not only of granulocyte-macrophage colonies, but also of erythrocytes, megakaryocytes, mast cells, blast cells, and mixed hematopoietic colonies. In this report, we evaluated the in vivo effects of hGM-CSF on hematopoietic and lymphopoietic responses in the hGM-CSFR Tg-mice. Administration of this factor to Tg-mice resulted in dose-dependent increases in numbers of reticulocytes and white blood cells (WBCs) in the peripheral blood. Morphological analysis of WBCs showed that the numbers of all types of the cell, including neutrophils, eosinophils, monocytes, and lymphocytes increased; the most remarkable being in lymphocytes that contained a number of large granular lymphocytes (LGLs) in addition to mature T and B cells. However, total cellularity of the BM of the Tg-mice decreased in a dose-dependent manner when hGM-CSF was injected. In sharp contrast to the BM, spleens of the Tg-mice were grossly enlarged. Although all types of blood cells and hematopoietic progenitors increased in the spleen, erythroid cells and their progenitors showed the most significant increase. Increased numbers of megakaryocytes and LGLs were also observed in spleen and liver of the treated Tg-mice. Flow cytometric analysis showed that LGLs expanded in Tg-mice expressed Mac-1+ CD3- NK1.1+. The thymus of Tg-mice treated with hGM-CSF exhibited a dose-dependent shrinkage and a remarkable decrease in CD4+ CD8+ cells. Thus, hGM-CSF stimulated not only myelopoiesis but also erythropoiesis and megakaryopoiesis of hGM-CSFR Tg-mice in vivo, in accordance with our reported in vitro findings. In addition, hGM-CSF affected the development of lymphoid cells, including natural killer cells of these Tg-mice.     

Numerical simulation of parallel-plate particle separator for estimation of charge distribution of PM2.5

A numerical simulation of an instrument that is used to measure the charging state of PM2.5 is conducted in order to clarify its measurement uncertainty and to improve its performance. The instrument, a parallel-plate particle separator (PPPS), is designed to classify aerosol particles according to their charging states and measure their quantities. The trajectories of submicron particles in the PPPS are numerically analyzed using the Lagrangian particle tracking method, taking into account the Brownian force and the electrostatic force. First, it is confirmed that the deterioration in the classification accuracy observed in the experiment is due to Brownian diffusion. The optimal condition that improves the accuracy is investigated through a parametric study by varying the balance of flow rates at the inlets, the geometry of the inlet and exit sections, and the applied voltage. It is found that decreasing the flow rate of the central inlet for aerosol or narrowing the central inlet improves the accuracy. The dependence of the accuracy on the flow rate is found to be in accordance with the experimental results. For charged particles, an optimum voltage that maximizes the classification accuracy is found. On the basis of the simulation results, we propose a method to determine the charge distribution of aerosol from the number of particles counted at each exit of the PPPS. In the test assuming aerosol in the air, the charge distribution determined from the number count at the exits is found to perfectly agree with the charge distribution specified at the inlet.

Copyright © 2019 American Association for Aerosol Research     

Separation of Polyvinyl Chloride from Plastic Mixture by Froth Flotation after Surface Modification with Ozone

Selective modification by ozonation for the surface of polyvinyl chloride (PVC) was evaluated to separate PVC from the other plastics, polyethylene terephthalate (PET), polycarbonate (PC) and polymethyl methacrylate (PMMA), with almost the same density as PVC by the froth flotation process. Ozonation could selectively decrease the contact angles of flexible PVC from 87.5 degrees to 68.4 degrees and rigid PVC from 90.3 degrees to 66.9 degrees, whereas little decreases in the contact angle were observed for other plastics. This would be due to the replacement of the chloride group on the surface of PVC, into hydrophilic functional groups; carbonyl, carboxyl and ester group. The PVC was successfully separated from the other plastics by the froth flotation process after the selective surface modification by ozonation.     

New type of tin support for hydroprocessing catalyst

TiN supported molybdenum sulfide catalysts showed much higher activity for cleavage of C-C bonds than oxide supported molybdenum sulfide catalysts, indicating the possibility of a new generation of supports for hydroprocessing catalysts.     

Phase separation behavior and morphology development of phenolic resin/PMMA/hexamethylenetetrarnine blends

Summary In order to obtain materials with nanopores which will be applicable for many fields, the structures of the cured blends of phenolic resin (PhN), poly(methyl methacrylate) (PMMA) and curing agent were studied. After PMMA was extracted from cured blends, the structures of cured phenolic resins were observed with SEM. As a results, it was found that nanosized continuous pore structures were formed in extremely wide composition region if curing temperature was high.     

Negative emotion recognition using multimodal physiological signals for advanced driver assistance systems

Artificial Life and Robotics - Recent advanced driver assistance systems’ (ADASs) control cars to avoid accidents, but few of them consider driver’s comfort. To realize comfortable...     

Fatigue striation in a wide range of crack propagation rates up to 70 μm/cycle in a ductile structural steel

The relationship between striation spacing and fatigue crack propagation rate up to 70 m/cycle was investigated for a ductile structural steel, qualified as JIS SM58Q. A modified compact-type specimen 400 mm wide and a centre-cracked specimen 200 mm wide were tested at a stress ratio, R, of 0 and 0.8. The fracture surface of the specimen was examined in detail under a scanning electron microscope. The crack propagation rate was expressed by a power function of the range of stress intensity factor from 0.1 to 70 m/cycle for R=0 and to 0.5 m/cycle for R=0.8. The striation spacing coincided with the fatigue crack propagation rate over the range 0.1 to 70 m/cycle. The profile of striation was found to be a ridge and valley type, and the ridges on one fracture surface coincided with those on the matching surface. It is suggested that the striation is formed by a plastic blunting mechanism.