Anomalies of the tracheobronchial tree in patients with esophageal atresia

Bone marrow examination revealed a lipid-laden histiocytosis in seven patients undergoing long-term total parenteral nutrition necessitated by extensive short-bowel surgical resection. Clinical abnormalities occurred during this treatment which required bone marrow examination. These included hepatosplenomegaly and peripheral blood cytopenia; the median time to the detection of these abnormalities was 64 months. The most striking change within the bone marrow was the presence of many pigment-laden histiocytes which had the typical morphology of sea-blue histiocytes seen in the so-called idiopathic sea-blue histiocyte syndrome. The occurrence of sea-blue histiocytosis in the bone marrow in association with long-term parenteral nutrition for short-bowel syndrome has not, to our knowledge, been reported previously and should now be considered in the differential diagnosis of bone marrow sea-blue histiocytosis.     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

Stability of fine water droplet clouds

The rate of evaporation of monodisperse water droplets was first evaluated by solving numerically the modified Maxwell equation, assuming the cellular model for a droplet clouds. The results are discussed in comparison with those for a single isolated droplet, which can be obtained analytically. The critical conditions for the droplet cloud to be stable are then evaluated as a function of droplet number concentration, droplet size and initial conditions of the surrounding air. Secondly, the equilibrated system, where a water droplet cloud is steadily mixed with unsaturated air, was analysed on the basis of enthalpy and material balance of the system to evaluate the total volume change of the droplets. Some of these analyses were verified by experiment, using an ultramicroscopic technique which is useful for droplet size analysis.     

Heterogeneous nucleation of organic vapours on a cold substrate

The heterogeneous phase transition of the organic vapours, cyclohexane and p-xylene, on a cold substrate was observed by cooling the substrate at a slow rate under reduced pressure conditions. Either organic vapour at a vapour pressure lower than 130 Pa formed directly solid crystals but p-xylene vapour at a higher vapour pressure formed liquid condensates with subsequent formation of solid crystals. The dependence of the critical supersaturation ratios on the critical temperatures and the physical properties of the organic vapours has been clarified by the equation derived on the basis of classical nucleation theory.     

Influences of perforation ratio in characteristics of capacitive micromachined ultrasonic transducers in air

Capacitive micromachined ultrasonic transducers (CMUTs) with a perforated membrane have been fabricated and characterized in air. Two types of CMUT device have been fabricated having perforation ratio (area ratio of holes = AR) of 10% and 20%, and analyzed about electrical and mechanical characteristics. The perforation ratio (AR) of membrane substantially influences on the electrostatic force and mechanical restoring force of the device since it leads to the area variation of electrode and membrane, it subsequently influences on the sensitivity and frequency response of the CMUT device. The electrostatic force and mechanical restoring force were improved by decreasing the AR and increasing the DC bias voltage. The open-circuit sensitivity of a CMUT having AR 10% membrane, 8.45 μV/Pa, is larger than that of AR 20%, 4.07 μV/Pa at DC 15 V. Furthermore, the resonance behaviors were observed in the range of 60-80 kHz, and the resonance frequency could be changed by varying the applied DC voltage and AR.     

Preparation of ferroelectric Ba(Ti/sub 0.85/Sn/sub 0.15/)O/sub 3/ thin films by metal-organic decomposition

Ferroelectric Ba(Ti/sub 0.85/Sn/sub 0.15/)O/sub 3/ (BTS/sub 15/) thin film is newly prepared on the Pt/Ti/SiO/sub 2//Si substrate by metal-organic decomposition. The firing condition is determined by thermogravimetric and differential thermal analysis. The BTS/sub 15/ thin film with a flat surface and uniform thickness is obtained by spin coating in N/sub 2/ atmosphere that avoids moisture. The BTS/sub 15/ film has a perovskite phase and a preferential [110] texture. It is also found that the crystalline structure is cubic at 24/spl deg/C with a lattice constant of 4.01 /spl Aring/, and a grain size of about 30 nm was estimated by Scherrer equation and SEM image. From P-E hysteresis loop at 20/spl deg/C, the polarization at E=0 and the electric field at P=0 are found to be 1.07 /spl mu/C/cm/sup 2/ and 24.0 kV/cm, respectively. It is observed that the dielectric constant decreases monotonously from about 830 to 630 with increasing temperature ranging from 20/spl deg/C to 50/spl deg/C. Finally, it is found that the BTS/sub 15/ thin film shows a sufficient ferroelectricity and is an attractive material for functional ferroelectric devices, such as thermal-type infrared sensors.     

Studies on analysis of terpene resin in imported chewing gums

We have developed an analytical method for terpene resins in chewing gum. The fraction including terpene resins was prepared by means of hexane extraction and two silica gel column chromatography treatments (hexane and ethyl acetate) from chewing gum. The terpene resin fraction was analyzed with LC/MS and IR. The terpene resins are mixtures of polymeric pinene and/or limonene, which have a monomer molecular weight of 136. The MS spectrum of the terpene resin peak on the LC/MS total ion chromatogram showed protonated molecular ion (M + H)+ peaks at intervals of m/z 136, characteristic of a complex mixture of polyterpenes. IR spectroscopy is a suitable technique to identify the terpene resin type, ie., pinene or limonene. When the method was applied to imported chewing gum sold in Japan, terpene resins were clearly detected.     

Morphology‐dependent electrocatalytic activity of nanostructured Pt/C particles from hybrid aerosol–colloid process

An optimum nanostructure and pore size of catalyst supports is very important in achieving high catalytic performances. In this instance, we evaluated the effects of various carbon nanostructures on the catalytic performances of carbon‐supported platinum (Pt/C) electrocatalysts experimentally and numerically. The Pt/C catalysts were prepared using a hybrid method involving the preparation of dense, hollow, and porous nanostructured carbon particle via aerosol spray pyrolysis followed by microwave‐assisted Pt deposition. Electrochemical characterization of the catalysts showed that the porous Pt/C catalyst gave the best performance; its electrochemical surface area was much higher, more than twice than those of hollow or dense Pt/C. The effects of pore size on electrocatalysis were also studied. The results showed the importance of a balance between mesopores and macropores for effective catalysis with a high charge transfer rate. A fluid flow model showed that good oxygen transport contributed to the catalytic activity. © 2015 American Institute of Chemical Engineers AIChE J, 62: 440–450, 2016     

Physiology and Pathophysiology of Heparan Sulfate in Animal Models: Its Biosynthesis and Degradation

Heparan sulfate (HS) is a type of glycosaminoglycan that plays a key role in a variety of biological functions in neurology, skeletal development, immunology, and tumor metastasis. Biosynthesis of HS is initiated by a link of xylose to Ser residue of HS proteoglycans, followed by the formation of a linker tetrasaccharide. Then, an extension reaction of HS disaccharide occurs through polymerization of many repetitive units consisting of iduronic acid and N-acetylglucosamine. Subsequently, several modification reactions take place to complete the maturation of HS. The sulfation positions of N-, 2-O-, 6-O-, and 3-O- are all mediated by specific enzymes that may have multiple isozymes. C5-epimerization is facilitated by the epimerase enzyme that converts glucuronic acid to iduronic acid. Once these enzymatic reactions have been completed, the desulfation reaction further modifies HS. Apart from HS biosynthesis, the degradation of HS is largely mediated by the lysosome, an intracellular organelle with acidic pH. Mucopolysaccharidosis is a genetic disorder characterized by an accumulation of glycosaminoglycans in the body associated with neuronal, skeletal, and visceral disorders. Genetically modified animal models have significantly contributed to the understanding of the in vivo role of these enzymes. Their role and potential link to diseases are also discussed.