Ammonia production using iron nitride and water as hydrogen source under mild temperature and pressure

Ammonia generation was studied in the reaction between water and nitrogen-containing iron at 323 K and atmospheric pressure. Similar to metallic Fe, the interstitial compound Fe₃N reduced water through Fe oxidation to produce hydrogen gas, while the N combined with atomic hydrogen to produce ammonia as a byproduct. The addition of carbon dioxide to this system accelerated the reaction with concomitant consumption of carbon dioxide. The promoted ammonia production upon addition of carbon dioxide can be attributed to the generation of atomic hydrogen from the redox reaction of carbonic acid and Fe, as well as removal of used Fe from the reaction system through the formation of a soluble carbonato complex. When carbonate was added to the reaction system, the production rates of ammonia and hydrogen increased further. The results here confirmed that ammonia can be synthesized from iron nitride under mild conditions by utilizing carbon dioxide.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Volumetric Change and Surface Properties of Temperature-Sensitive Polyvinylalcohol (PVA) Hydrogel

Polyvinylalcohol (PVA) polymer gel is a temperature sensitive polymeric gel, with a critical transition temperature (with H₂O) of 310 K. At higher than 310 K, this temperature sensitive polymer gel shrinks because of discharging water, whereas at lower temperatures, the gel swelled because of absorbing water. The reversibility of the gel's volume change was confirmed by temperature swing. The adsorption behavior of an organic compound onto the PVA polymer gel in water was tested at various temperatures. The amount of adsorbed organic compound increased remarkably at temperatures higher than about 310 K. Then, it was confirmed that the organic compound in PVA polymer gel could be reversibly adsorbed and desorbed by a temperature change between 293 and 323 K. The mechanism of adsorption of the organic compound onto the PVA polymer gel could be explained by hydration and dehydration of polymer gel.     

Relation between encoder and syndrome former variables and symbol reliability estimation using a syndrome trellis

We derive a linear correspondence between the variables of an encoder and those of a corresponding syndrome former. Using the derived correspondence, we show that the log-likelihood ratio of an information bit conditioned on a received sequence can be equally calculated using the syndrome trellis. It is shown that the proposed method also applies to recursive systematic convolutional codes which are typical constituent codes for turbo codes. Moreover, we show that soft-in syndrome decoding considering a priori probabilities of information bits is possible in the same way as for Viterbi decoding based on the code trellis. Hence, the proposed method can be applied to iterative decoding such as turbo decoding. We also show that the proposed method is effective for high-rate codes by making use of trellis modification.     

1-GHz-spaced 16-channel arrayed-waveguide grating for a wavelength reference standard in DWDM network systems

We fabricated a 1-GHz-spaced 16-channel arrayed-waveguide grating (AWG) by using a new AWG configuration where the path of each arrayed waveguide winds backward and forward across a 4-in diameter wafer without crossing any other waveguides. The ultra-narrow (< 1 GHz) and stable transmission bands of this AWG can be used to construct a wavelength reference standard covering the S, C, and L bands in the dense wavelength-division-multiplexing network systems whose frequency deviation is /spl plusmn/160 MHz.     

Low-loss athermal silica-based lattice-form interleave filter with silicone-filled grooves

We describe a low-loss athermal silica-based interleave filter with a lattice-form structure. We athermalize the filter by using a silicone-filled groove formed in each delay line and we employ a low-loss design to reduce the accumulated groove excess loss in the multiple delay lines. By using these designs, we obtained a very low groove excess loss of 0.4 dB and achieved satisfactory temperature insensitivity and optical characteristics with this filter.     

Extremely low-loss 1.5%-/spl Delta/ 32-channel athermal arrayed-waveguide grating multi/demultiplexer

A silica-based 1.5%-/spl Delta/ 100 GHz-spacing 32-channel athermal arrayed-waveguide grating (AWG) with compact size and extremely low insertion loss is described. By reducing the fibre coupling loss and the excess loss in a silicone-filled groove, an insertion loss of 1.3 dB was achieved with this athermal AWG.