Planar lightwave integrated circuits with embedded actives for board and substrate level optical signal distribution

This paper explores design options for planar optical interconnections integrated onto boards, discusses fabrication options for both beam turning and embedded interconnections to optoelectronic devices, describes integration processes for creating embedded planar optical interconnections, and discusses measurement results for a number of integration schemes that have been demonstrated by the authors. In the area of optical interconnections with beams coupled to and from the board, the topics covered include integrated metal-coated polymer mirrors and volume holographic gratings for optical beam turning perpendicular to the board. Optical interconnections that utilize active thin film (approximately 1-5 /spl mu/m thick) optoelectronic components embedded in the board are also discussed, using both Si and high temperature FR-4 substrates. Both direct and evanescent coupling of optical signals into and out of the waveguide are discussed using embedded optical lasers and photodetectors.     

Carbonization of coals into anisotropic cokes: 7. Copreheat-treatment under short contact-time conditions at high temperature

The copreheat-treatment of non-fusible and slightly fusible coals with A240 and hydrogenated A240 under high temperature-short contact-time conditions around 500 °C has been examined in an attempt to produce a formed coke with better anisotropic development. These conditions shortened the copreheat-treatment time and provided better anisotropic development in the resultant coke after carbonization. Effectiveness of short contact-time has been discussed in terms of the extent of depolymerization of coal molecules suitable for anisotropic development, this being related to coal liquefaction under similar conditions.     

Analysis of brushless three-phase synchronous generator without exciter

Recently, a demand for small-capacity generators has been increasing as electric sources in small ships and automobiles or as portable electric sources driven by engines. It is desired that the structure of small-capacity generators be simple and robust, and that the generators be highly reliable, easily maintained and controlled. This paper describes an analysis of the original brushless synchronous generator without exciter. The output voltage can be adjusted in the wide range by controlling the stator dc current. To analyze the characteristics of this generator, the finite element method is applied. It is found that the results of theoretical analysis agree well with the experimental results.     

Longitudinal elastic waves in columns due to earthquake motion

An analysis is presented of longitudinal waves in a thin elastic column. Velocity is specified at one end, and the boundary condition at the other end is expressed in terms of a range of effective impedances of an attached structure. Propagation, reflection and interference of the waves are followed by the method of characteristics. Integration of differential equations along characteristics yields the wave-induced stress, which is then applied to problems of earthquake excitation. Numerical examples are given for recorded updown ground motion of the Kobe Earthquake.     

Effects of Particle Size of Bulk Drug and food on the Bioavailability of U-78875 in Dogs

The effects of particle size and food on the absolute bioavailability of U-78875 in dogs after oral administration of either a suspension or tablet dosage form were investigated. A reduction of particle size caused a significant increase in bioavailability along with an increase in dissolution rate. Additionally, both suspension and tablet dosage forms administered after food caused an increase in bioavailability. Thus, to accelerate drug dissolution, a reduction of U-78875 particle size from the unmilled state is important for the optimization of formulation compositions. To increase the bioavailability of U-78875, postprandial dosing should be considered.     

Simultaneous measurement of the resistivity and permeability of afilm sample with a double coil

A method is proposed for a simultaneous measurement of the resistivity and permeability of a film inserted between two coils facing each other. Connecting in series, the total impedance of the coils was measured in two ways, i.e., 1) the current passes through the coils in the same direction, and 2) the current passes through each coil in opposite directions to each other. The resistivity and permeability of the film were simultaneously obtained from the difference in the impedance for the two cases. It was theoretically found that the optimum frequency for high accuracy in the measurement was proportional to the resistivity and inversely proportional to a thickness of a sample film. The results of the simultaneous measurements of the resistivity and permeability of nickel films of a thickness ranging from 0.01-0.08 mm at a frequency range of 1-100 kHz are shown in this paper. The measured values of the resistivity and permeability with this method agreed with the values obtained by conventional methods, i.e., the dc four-probe method for the resistivity measurement and the toroidal coil method for the permeability measurement     

Current collecting efficiency of micro tubular SOFCs

In this study, current collecting efficiency of the micro tubular solid oxide fuel cell (SOFC) was estimated to determine optimum size of the micro tubular SOFC. Two models for collecting current from single terminal (ST) and double terminal (DT) of anode tube were proposed and used to calculate the current collecting efficiency as functions of anode thickness, tube length and operating temperature. It was shown that design of the cell geometry and current correcting method are significantly important to achieve high performance micro tubular SOFC stacks. The efficiency loss estimated from the DT model was about 2–4-fold lower than those of obtained from the ST model. The DT model was shown to be more effective for higher operating temperature and the tube length.     

Wide gamut LCD using locally dimmable four‐primary‐color LED backlight

This paper proposes a wide gamut LCD using locally dimmable four‐primary‐color (4PC) LED backlight. Although the color gamut of LCDs has been improved in recent years, it is insufficient to reproduce all the colors in the real world. The objective of this paper is to propose a wide gamut LCD that reproduces all the colors in the real world while keeping the cost increases to a minimum. We evaluated the color gamut reproduced by LEDs of multiple primary colors and selected cyan as the optimal color to be added to the three primary colors to reproduce all the colors in the real world. Therefore, we designed an LED backlight consisting of an additional only‐cyan LED with three‐primary‐color LEDs and developed a prototype LCD with 4PC LED backlight. Furthermore, we developed a local dimming algorithm for the 4PC LED backlight. As a result, we confirmed that the prototype LCD with the 4PC LED backlight is able to cover almost all the colors in the real world and also able to display natural images with highly saturated colors by local dimming.     

Adsorption of urea,creatinine, and uric acid from three solution types using spherical activated carbon and its recyclability

In this paper, we propose that the urinary toxins from the wastewater be adsorbed on an adsorbent such as spherical activated carbon and the latter be regenerated by subjecting it to high temperatures to recycle activated carbon and also to recycle the water used in dialysis. We studied the adsorption of artificial waste dialysate, which is a mixed solution of urea, creatinine, and uric acid, and the separate solutions for each of these and found that their extents of adsorption onto the spherical activated carbon material were nearly identical. The amount of adsorption was approximately 1.4 mg·g^-1 for urea, 18 mg·g^-1 for creatinine, and 20 mg·g^-1 for uric acid. The urea, creatinine, and uric acid adsorbed onto the spherical activated carbon decomposed on heat treatment at 500℃, and the adsorption capacity of the spherical activated carbon was regenerated. Our study successfully demonstrated that the spherical activated carbon can be recycled in the waste dialysate treatment process.