Markedly compressible behaviors of gellan hydrogels in a constrained geometry at ultraslow strain rates

The fracture behaviors of gellan hydrogels under compression remarkably depend on the strain rate as well as the boundary conditions for lateral expansion. In the geometry with no constraint for lateral expansion (conventional uniaxial compression), the gels rupture at relatively small strains independently of the compression rates. In contrast, when the gels are compressed extremely slowly (at a strain rate of ca. 10⁻⁵ s⁻¹) in the geometry prohibiting the lateral expansion at their top and bottom surfaces, they are remarkably compressible down to 2% of the initial height without macroscopic fracture and they are accompanied by a large amount of water release. In such markedly compressed gels, many microscopic cracks are formed around the central layer, where strain concentration occurs due to the nonuniform deformation arising from the constrained geometry. In the highly compressible case, the formation of macroscopic cracks is prevented by the localization of microscopic cracks as well as the enhancement in mechanical toughness by a significant increase in polymer concentration due to water release.     

Synthesis of fine composite particles for hydrogen storage, starting from Mg-YNi2 mixture

We synthesized new composite particles for hydrogen storage on the basis of an idea of “particle designing”. As starting materials, powders of Mg and YNi₂ were selected. Fine composite particles containing mainly Mg₂Ni could be designed by repetitive hydriding and dehydriding cycles at 673 K. In the synthesis process of the composite particles, the following two points were found to be essential for this technique. The first point is that, after being activated by the sequential processes of hydrogenation, amorphization and disproportionation, YNi₂ reacts effectively with Mg. The second point is that evaporated Mg, which occurs during dehydriding, adheres to the surface of the activated YNi₂ and accelerates a diffusion reaction to form Mg₂Ni at the interface. In these composite particles, Mg₂NiH₄ is formed, even at 373 K, under a hydrogen pressure of 5 MPa.     

Surface characterization and catalytic properties of La1−x -Sr x CoO3

The surface chemical states of the perovskite-type compounds, strontium doped lanthanum cobalt oxides (La_1?x Sr _x CoO₃), have been investigated using X-ray photoelectron spectroscopy (XPS). Catalytic oxidations of both methane and CO have also been investigated using flow methods. The chemical composition of the surface of La_1?x Sr _x CoO₃ was very different from that in the bulk, which was measured by X-ray fluorescence spectroscopy (XRFS). The catalytic activity of La_1?x Sr _x CoO₃ increased with an increase in the quantity of cobalt atoms on the surface.     

Development of next generation PWR in Japan

The demand for energy in Japan is expected to increase steadily into the future, and it seems that the importance of nuclear power generation will be heightened more when the situation of our country which is not rich in energy resources is taken into account.

Furthermore, when we consider the present situation that the light water reactors have become common, recent outlook for the supply and demand for uranium resources, trends in the development of the fast breeder reactor technology, etc., the light water reactors are expected to remain dominant in the nuclear power generation of our country until at least the second half of the 21st century.

Based on such a background five PWR utilities in Japan (Hokkaido, Kansai, Shikoku, Kyushu, and the Japan Atomic Power), and Mitsubishi Heavy Industries, Ltd. have jointly started researching the Next Generation PWR which is expected to be the leading nuclear power plant taking place of APWR.     

Adsorption properties of oxygen and methane on Ga-ZSM-5; the origin of the selectivity of NOx reduction using methane

The adsorption properties of oxygen and methane on Ga-ZSM-5 and Cu-ZSM-5 catalysts were examined by a TPD method to clarify the extraordinary selectivity of HC-SCR using methane on Ga-ZSM-5. It was observed that Ga-ZSM-5 did not adsorb oxygen but adsorbed methane dissociatively, while on Cu-ZSM-5 oxygen was dissociatively adsorbed and reacted with adsorbed ethylene.     

Slit flow of molten polyethylene filled with plastic flakes

The processability of polyethylene in sheet-extrusion or calendering may be improved by the addition of plastic flakes. The effects of plastic flake parameters and flow conditions on the viscosity and the die swell of the suspension were determined, and the structure in flow (morphology or dispersion state) and applications were discussed. Flakes of biaxially oriented polystyrene, high-impact polystyrene, polypropylene, polyamide or polypropylene spheres were dry-blended with polyethylene. The viscosity was determined by means of a slit or a capillary rheometer. The quenched extrudate was annealed and its die swell was measured. Flakes of biaxially oriented polystyrene shrunk into rod-like form during heating, but other plastics retained the flake-form. The relative viscosity and the swell ratio of the suspensions depended on the type of plastic and operating conditions. The rheological behavior of suspensions qualitatively suggested that polypropylene flakes deformed or crowded (including stacking), polyamide flakes deformed slightly, and polystyrene flakes were difficult to buckle, but crowded slightly. The thickness of extrudates can be controlled easily by flake addition due to decreased die swell, while the output would be reduced to some extent.     

Properties of networks obtained by internal plasticization of epoxy resin with aromatic and aliphatic glycidyl compounds

In order to improve the fracture properties of p, p′-diaminodiphenylmethane-cured epoxy resin, various kinds of aromatic and aliphatic glycidyl compounds were investigated as a modifier at an amount of 30 wt %. Several compounds promoted the fracture toughness. In any glycidyl compounds, however, heat resistance was decreased by the modification. The dynamic mechanical properties of the modified epoxy resins were measured. The crosslinking density ρ was calculated from the theory of rubber elasticity, and the mechanical properties of the resins were discussed in regard to the crosslinking density. Tensile strength was scarcely affected by the crosslinking density. Elongation at break and Izod impact strength increased remarkably with decrease in crosslinking density. The fracture toughness K_Ic- increased with decrease in crosslinking density except at small ρ.     

Impregnation of silk sericin into polyester fibers using supercritical carbon dioxide

Silk sericin was impregnated into polyester fabric using supercritical carbon dioxide (SCCO₂) to overcome polyester hydrophobicity. The effects of sericin molecular weight, pH of sericin, solution and cosolvent types on sericin impregnation were investigated. Enzyme‐hydrolyzed, acid‐, based‐hydrolyzed sericin in SCCO₂, and a 30 kDa sericin in SCCO₂ modified with cosolvents such as water, methanol, 1‐propanol, and acetone; and a modifier: sodium hydroxide solution were used in this work. Impregnation of sericin in polyester was indicated by Fourier transform infrared spectrophotometry (FTIR) and dyeing with acid dye. Degradation of polyester fibers during SCCO₂ process was indicated by scanning electron microscopy (SEM). Methylene blue dyeing was used to realize carboxyl group in polyester. The results showed no impregnation of sericin into polyester by using SCCO₂ modified with cosolvents. However, sericin was impregnated into modified surface polyester since hydrophilic groups such as carboxyl and hydroxyl groups were regenerated by alkaline hydrolysis. Samples impregnated with hydrolyzed sericin showed high color strength of Supranolechtbordeaux B acid dye. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007